User`s guide

Preferences
Toggle Yes and No
SET
SET
Toggle °F and °C
SET
SET
Toggle 12-hour clock and 24-hour clock
SET
SET
Press Light
To show rst item in Preferences menu
(F/C)
for 12-24
Press Light for REMINDERS
Press Light
Only if Cleanup
Cycle is enabled.
RF Dolphin only.
Press Light for CLEAN UP
While the Temperature is
still ashing, press Light
repeatedly until PREF
appears in the LCD.
SET
RANGE
Main Screen
READY
RANGE
FLTR1
To next item in
Main Menu
(UTIL)
To next item in
Main Menu
(UTIL)
To view current setting and to toggle number of hours (0-4).
SET
SET
SET
To veiw current setting and to toggle address numbers for Dolphin II or Dolphin III (0-7)
SET
SET
SET
to show Address Menu for Dolphin II or Dolphin III
To Set
To Set
To Set
To Set
To Set
Wait to
Revert
*****
Wait to
Revert
*****
Wait to
Revert
*****
Wait to
Revert
*****
Wait to Revert
*****
Several Seconds
OR
Wait Several Seconds to
Return to Main Screen
OR
Indicates Flashing or Changing Segment
Key
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel conguration
Indicates Alternating or Progressive Message - every 1/2 second
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original setting and
ignores any change to that menu item.
*****
Indicates a Menu Item that
Depends on a Manufacturer
Conguration and
may or may not appear.
Preferences
Toggle Yes and No
SET
SET
Toggle °F and °C
SET
SET
Toggle 12-hour clock and 24-hour clock
SET
SET
Press Light
To show rst item in Preferences menu
(F/C)
for 12-24
Press Light for REMINDERS Press Light
Only if Cleanup Cycle is enabled. RF Dolphin only.
Press Light for CLEAN UP
While the Temperature is
still ashing, press Light repeatedly until PREF appears in the LCD.
SET
RANGE
Main Screen
READY
RANGE
FLTR1
To next item in
Main Menu
(UTIL)
To next item in
Main Menu
(UTIL)
To view current setting and to toggle number of hours (0-4).
SET
SET
SET
To veiw current setting and to toggle address numbers for Dolphin II or Dolphin III (0-7)
SET
SET
SET
to show Address Menu for Dolphin II or Dolphin III
To Set To Set
To Set
To Set To Set
Wait to Revert
*****
Wait to Revert
*****
Wait to Revert
***** Wait to Revert
*****
Wait to Revert
*****
Several Seconds OR
Wait Several Seconds to Return to Main Screen OR
Indicates Flashing or Changing Segment
Key
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel conguration
Indicates Alternating or Progressive Message - every 1/2 second
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original setting and
ignores any change to that menu item.
*****
Indicates a Menu Item that Depends on a Manufacturer Conguration and may or may not appear.
Adjusting the Set Temperature
When using a panel with Up and Down buttons (Temperature buttons), pressing Up or Down will cause the temperature to
flash. Pressing a temperature button again will adjust the set temperature in the direction indicated on the button. When
the LCD stops flashing, the spa will heat to the new set temperature when required.
If the panel has a single temperature button, pressing the button will cause the temperature to flash. Pressing the button
again will cause the temperature to change in one direction (e.g. UP). After allowing the display to stop flashing, pressing
the Temperature Button will cause the temperature to flash and the next press will change the temperature in the opposite
direction (e.g. DOWN).
Press-and-Hold
If a Temperature button is pressed and held when the temperature is flashing, the temperature will continue to change
until the button is released. If only one temperature button is available and the limit of the Temperature Range is reached
when the button is being held, the progression will reverse direction.
Dual Temperature Ranges
This system incorporates two temperature range settings with independent set temperatures. The High Range designated in
the display by an “up” arrow, and the Low Range designated in the display by a “down” arrow.
These ranges can be used for various reasons, with a common use being a “ready to use” setting vs. a “vacation” setting.
The Ranges ar
e chosen using the menu structure below. Each range maintains its own set temperature as programmed by
the user. This way, when a range is chosen, the spa will heat to the set temperature associated with that range.
For example:
High Range might be set between 80°F and 104°F.
Low Range might be set between 50°F and 99°F.
More specific Temp Ranges may be determined by
the Manufacturer.
Freeze Protection is active in either range.
See Ready and Rest on Page 6
for additional heating control information.
Temperature and Temp Range
High-Range vs.
Low-Range Temp Choice
Press a Temp Button repeatedly to change the temperature.
Pressing and holding a Temp Button will also change the temperature.
Pressing and holding a Temp Button will also change the temperature.
Toggle the Range arrows in the LCD.
SET
RANGE
SET
RANGE
Set Temp will Show & Flash
Set Temp will Show & Flash
SET
RANGE
FLTR
1
SET
RANGE
FLTR
1
SET
RANGE
FLTR1
SET
RANGE
SET
RANGE
Waiting
Several Seconds
Reverts to Original Setting
To Set
*****
SET
RANGE
While
temperature
is ashing...
To next item in Main Menu
Main Screen
READY
RANGE
FLTR1
Main Screen
READY
RANGE
FLTR1
Several Seconds
OR
Main Screen
READY
RANGE
FLTR1
Press a Temp Button repeatedly to change the temperature.
Several Seconds
OR
Main Screen
READY
RANGE
FLTR1
Main Screen
READY
RANGE
FLTR
1
Indicates Flashing or Changing Segment
Key
A temperature button, used for “Action”
Light or dedicated “Choose” button, depending on control panel
conguration
Indicates Alternating or Progressive Message - every 1/2 second
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original
setting and
ignores any change to that menu item.
*****