Owner's Manual

Bu tt on
It em
1
2
12 V/ 24 V
12 .1 V/ 24 .2 V
12 .2 V/ 24 .4 V
2
8
3
8
4
12
5
24
6
36
7
Cut Off Time(Hrs)
Cut Off Voltage
NOTE: There is a risk of electric shock, be sure to use aninsulated
environment and insulated tools.
(9
HHH(Alwayson)
Time Setting Button I
OFF TIME SEfflNG
0
11.6V/23.2V
11.7V/23.4V
11.8V/23.6V
11.9V/23.8V
Voltage setting button
Thepow e rsupplyisstoppedwhentheset time has elapsed sinceACC was turned off(atthe startofparki.ngi
(DPressandholdtheotftimesettingbuttonfor3secoudsandthenumberontheLCDwillflash.
@When the numberllashes,pres.o; the off time setting button each timetoadjwtthe time.
@When the time you want di5play on the LCD (wait 8 seconds without pressing button) th en your setting will
becomplete.
:$iHHH is a setting that does not use as a timer. & a result, power is already flowing. If the battery voltage
dropsevenwithintheDfftime5'tting.thecutoffvoltagesettinghaspriorityandwillstop.
*The setting voltage and time may have an e rror of a bout ±3¾ depending on the usage e nvironment
Voltage Setting Button B
VOLTAGE CIIT OFF SETI1NG
Whenthebatterydisdwgeandvoltagedrop.o;be\owtherutoffsetting.thepowersupplywillbestopped
(DPress and hold the voltage setting button for 3 seconds and number of the LCD will flash.
@When the numb er flashes,pressth e voltag e settingbuttontoadjustthetime
@When the voltage you want is displayed on the LCD [wait 8 seconds without pressing button] then
y oursettingwillbecomplete.
Not ed choosethesuitablesettingforyourvehicle.
Smart Hardwire Kit SHWC User's Guide
Thankyouforpurchsingourproducts. Forsafeandcorrectuseofthisproduct,pleasereadthis
manual carefully.
*Mounting Method:
Before wiring into the car, make sure this product and dash cam works properly
before installing, After installation, be sure to check that all in-vehicle products,
electronic components, vehicle operating conditions are working properly.
If you feel abnormal or uncomfortable, immediately stop using this product and install it at
yourdealerhelporoursupportcenter.
Directly wiring to the car:
Fuse Box BAT+ (*1)- Red
ACC (*1)-Yellow
GND (*1) - Black
-If you correctly wiring BAT+ and GND, the product light wiM flash red, auto run programme
successful, followed wiring ACC, blue light display the current voltage.
-Long press voltage setting key, II Voltage display in order, first comes current
voltage,thenfollowedwithacut-offsettingvoltage.
:IDvhenACC is OFF, if the current volt.age continues to drop lower than the voltage setting
within the 6 minutes the power will cut-off. This is to prevent the use of electric lifting
windows, tailgates and the electric sliding door when the car is not in drive, the battery
voltage is pulled down and the low voltage enters into protection mode in advance to
protect the battery from draining.
Wiri~ Guide
RED (BAT+)
To car camera
.-
YELLOW(ACC) -- i= = :t= ci ;(ii]: iJ=,=O -
. \.._________) .
BLACK(GND)
Input Ouput
TTTTTiTTTTT
Support Center:
www.mygekogear.com [e-mail]