CEP FRIDGE·FREEZER Operation Manual for AC/DC Fridge ·Freezer Model CEP 47 www.mycoolman.com.
CEP FRIDGE·FREEZER Contents Important Safety Warnings Important Product Information Product Features LED Control Panel & Operation Instructions Handle Fitting Instructions Two Way Opening and Removable Lid Emergency Override Cleaning & Maintenance Troubleshooting Status Indicator Notes Product Specifications Warranty Terms & Conditions page page page page page page page page page page page page page 2 3 3 4-5 6 7 8 8 9 10 11 12 12 Important Safety Warnings • DO NOT use if any of the electrical cables
CEP FRIDGE·FREEZER Important Product Information • Best performance is achieved in ambient temperatures between +10 °C and + 43 °C. • Temperatures above +32 °C may see a slight performance drop, and power consumption increase. • The lower the ambient temperature, the lower the power usage. In order to maximize efficiency, keep the unit in a cool location out of direct sunlight.
CEP FRIDGE·FREEZER LED Control Panel & Operation Instructions Control Panel CEP 47 Power/Status Indicator Light Power Switch Turbo Switch LED-Display Turbo Indicator Light Temperature Settings NOTE: Temperature can be set from –18 ºC to +10 ºC Turning the unit on and off: Step 1: Plug in the AC or DC power cable (ensure power is on at source). Step 2: Press the button once to turn on - To switch off press and hold the for 3 seconds.
CEP FRIDGE·FREEZER LED Control Panel & Operation Instructions Engaging Turbo mode: What is the purpose of Turbo Mode? It enables the compressor to run at a higher speed, therefore achieving faster cooling to your nominated temperature. Step 1: Press the button once to turn on. The light will illuminate green to indicate that Turbo Mode is engaged. Step 2: To turn off, press the button again. The green light will now go out to indicate that Turbo mode is no longer engaged.
CEP FRIDGE·FREEZER Handle Fitting Instructions In your myCOOLMAN CEP 47 you will receive handle kit. Contents: 1. 2 x handle assemblies (complete) 2. 8 x Hex Head SS set screws 3. 1 x 5 mm Hex tool (Allen key) Assembly process: Step 1: Place screw in handle and secure in location 1 Step 2: Use Hex tool to screw into the captive nut in body of CEP47 Step 3: Tighten about halfway Step 4: Repeat process at locations 2-3-4 Step 5: Tighten all screws fully without over-tightening.
CEP FRIDGE·FREEZER Two Way Opening and Rwemovable Lid Purpose for removing the lid: CEP 47 This lid can be removed to aid with cleaning and to change the opening direction. You can change the direction of the lid by following the below instructions. How to remove the lid: Open the lid fully, then overextend, pushing lid past the “fully open point” to remove. Keep fingers clear of base. How to attach the lid: Line the hinges up with the metal posts and press down firmly.
CEP FRIDGE·FREEZER Emergency Override Fuse 6.3A The Emergency Override Switch is located just below the main control panel next to the power inlets For normal operation the switch is in the “NORMAL USE” position. If the electronics in the display board fail or controls become non-functional, slide the switch to EMERGENCY OVERRIDE position. NOTE: • In EMERGENCY OVERRIDE, the cooler runs with full cooling capacity (i.e.
CEP FRIDGE·FREEZER Troubleshooting How to get the most out of your unit: • Best performance is achieved at ambient temperatures between +10 °C and +32 °C. • Product is rated as a ‘T Climate’ class (Tropical), which means that the units meet the requirements of ISO-15502 at 43 °C. • Higher ambient temperatures mean that the compressor will run faster and longer. • If the unit is in direct sun, this also increases the ambient temperature and may result in the compressor running faster and longer.
CEP FRIDGE·FREEZER Status Indicator E0 flash every 4 seconds temperature sensor issue: • Contact Leisure-Tec on 1300 07 2018 E1 flash every 4 seconds - low voltage & Battery Protection: • An E1 will occur when the battery protection level has been reached. i.e input voltage to low for protection setting, check power source voltage. • Try on different power source (vehicle or 240V AC power). If changing power source fixed issue, then possible issue with original power source.
CEP FRIDGE·FREEZER Notes: page 11
CEP FRIDGE·FREEZER Product Specifications Model Product descriptoin Dimensions / mm CEP47 Single Zone Fridge / Freezer Length 672 / Width 600 / Height 480 17.5 Weight / kg Connection voltage DC 12/24v / AC 100–240v 50–60Hz Rated current 12v 4.65 A / 24v 2.8 A / 240v 0.