Datasheet
Technische Beschreibung mySmartUSB Version 2.10 Seite: 3/14
www.myAVR.de © Laser & Co. Solutions GmbH - 07/2007 www.myAVR.com
Allgemeine Beschreibung
mySmartUSB ist ein kompakter USB-Programmer und Kom-
munikationsinterface für Atmel AVR-Mikrocontroller. Sie
können mit Hilfe dieses Boards eine Vielzahl von AVR-
Systemen ganz einfach über die vorhandene USB-
Schnittstelle programmieren oder mit den Systemen über
eine UART-USB-Bridge kommunizieren. Es ist ein an-
schlussfertiges Modul in SMD-Bauweise. Er verfügt über
spezielle Anschlussoptionen für das myAVR Board 2 USB
und Standard-ISP. Die Kommunikation mit dem PC läuft
völlig transparent über einen virtuellen COM-Port. Das Board
wird per USB-Schnittstelle mit dem PC verbunden und mit
Spannung versorgt. Es ist kein Parallel- oder COM-Port
nötig, was gerade für Notebookbesitzer von Vorteil ist.
General Description
mySmartUSB is a compact USB programmer and commu-
nication interface for Atmel AVR-microcontrollers. With this
board you can program a huge number of AVR systems or
communicate with them via an UART-USB-bridge. The USB
programmer mySmartUSB is produced in SMD technology
and fully equipped. It provides specific options to connect it
to our myAVR USB boards or to Standard-ISP. For commu-
nication with the PC it uses a virtual COM-Port. This means,
that you can simply plug in this board to the USB-interface of
your PC, and it will be supplied with power and ready to
communicate. A Parallel- or COM-Port is not necessary,
what is particularly an advantage for notebook owners.
Überblick
/
Overview
Eigenschaften
• einfache Kommunikation mit dem PC oder Notebook
über die USB-Schnittstelle
• Über den ISP-Adapter (in-system-programming) kön-
nen eine Vielzahl von AVR-Systemen programmiert
werden.
• 10 PIN Atmel Standardbelegung
• Interface für das myAVR Board 2 USB
• Industriestandard-Controller (CP2102) USB zu seriell
Konverter
• ATmega8 mit Firmware nach ATMEL AN910 und
AN911 Programmierstandard
• Schnelle Programmierung über USB 2.0 durch Block-
mode (AVR911)
• umschaltbar zwischen Programmier-, Kommunikati-
ons- und Ruhemodus
• Power On und Power Off durch Anwender schaltbar
• stellt einen virtuellen COM-Port zur Verfügung
• Zustandsanzeige (rote/grüne LEDs)
• Spannungsversorgung über USB-Anschluss
• Einfache Handhabung
• Updatefähig über Bootloader
• DIP Schalter für Betriebsart, Power, RESET und Boot-
loader
Properties
• Simple communication between microcontroller and
PC resp. Notebook via the USB-interface
• The ISP-Adapter allows it to program various AVR-
Systems.
• Standard Atmel 10 PIN assignment
• Interface for the myAVR Board 2 USB
• Industrial standard controller (CP2102)
USB to serial converter
• ATmega8 with firmware that supports ATMEL AN910
and AN911 programming standard
• Fast programming via USB 2.0 per block mode
• Switchable between programming, communication,
and neutral mode
• Power On and Power Off switchable by user
• Provides virtual COM-Port
• Status indication (red/green LEDs)
• Power supply over USB interface
• Simple handling
• Firmware-Updates over a boot loader
• DIP-switch for operating mode, power, programming
and data mode, RESET and boot loader
Spannungsversorgung
AVR Programmierung
UART Kommunikation
Standard ISP-
Programmierung
USB to UART Bridge
mit Hardware Handshake (RTS/CTS)
USB to TWI Bridge
USB to SPI Bridge
PC
mySmartUSB
Zielsystem /
target system
AVR910/ 911
Power
USB 2.0
UART
virtual COM
SPI
TWI
ISP