User manual
Technische Beschreibung / Technical description mySmartUSB light
Seite: 3/14
www.myAVR.de © Laser & Co. Solutions GmbH - 01/2010 www.myAVR.com
Allgemeine Beschreibung
mySmartUSB light ist ein modernes Programmierwerk-
zeug für Atmel AVR-Mikrocontroller im USB-Stick-Design.
Sie können mit Hilfe dieses Programmers eine Vielzahl von
AVR-Systemen unkompliziert und schnell über die vorhan-
dene USB-Schnittstelle programmieren. Der Programmer
wird als USB-Stick am PC oder Notebook angeschlossen
und mit Spannung versorgt. Das integrierte, intelligente
Spannungsversorgungsmodul erlaubt die Programmierung
von 5 V und 3,3 V Systemen. Die Programmierspannung
lässt sich dynamisch per Software umschalten. Da die Pro-
grammierung ohne Parallel- oder Serial-Port auskommt ist
dieser Programmer die ideale Wahl für alle Notebook-
Besitzer.
Der mySmartUSB light kann wahlweise mit einer
AVR910/AVR911 oder STK500 kompatiblen Firmware ge-
nutzt werden. Die Firmware verfügt über einen automati-
schen Step-Down-Modus für Controller mit langsamen Takt-
quellen.
General Description
mySmartUSB light is a modern programming tool for
Atmel AVR-Microcontroller in USB stick design. With this
board you can program a huge number of AVR systems
or communicate with them easy and fast via the usb inter-
face. You can simply plug in this board to the USB-
interface of your PC, and it will be supplied with power
and be ready to communicate. The integrated intelligent
Power supply modul allowed the supply und programming
of 5 V and 3,3 V systems. The programming-voltage is
dynamic switchable per software. A parallel or COM Port
is not necessary for programming, what is particulary an
advantage for notebook owners. mySmartUSB light can
be used in two different ways. Either you are using an
individual STK500 witch has firmware compatibility or and
AVR910/AVR911 compatible programmer. The firmware
has an special automatic step down mode for controllers,
Überblick
/
Overview
Eigenschaften
• einfacher Anschluss an den PC oder das Notebook
über die USB-Schnittstelle
• stellt einen virtuellen COM-Port zur Verfügung
• mit der ISP-Verbindung (in-system-programming)
können eine Vielzahl von AVR-Systemen program-
miert werden.
• 6 PIN Atmel Standard-ISP-Schnittstelle
• Industriestandard-Controller (CP2102) USB zu seriell
Konverter
• Firmwareprotokolle nach ATMEL AN910/911 oder
STK500v2 Programmierstandard
• Spannungsversorgung über USB-Anschluss
• Spannungsversorgung des Zielsystems
mit 5 V oder 3,3 V
• Power On und Power Off und Programmierspannung
durch Software schaltbar
• Zustandsanzeige (rote/gelbe/blaue LEDs)
• Einfache Handhabung
• Updatefähig über Bootloader
Properties
• Simple communication between microcontroller and
PC resp. Notebook via the USB-interface
• Provides virtual COM-Port
• The ISP-Adapter allows it to program various AVR-
Systems.
• Standard Atmel 6 PIN assignment
• Industrial standard controller (CP2102)
USB to serial converter
• firmware that supports ATMEL AN910 and AN911
programming standard or STK500v2
• Power supply over USB interface
• Switchable programming Power 5V / 3,3V
• Power On and Power Off switchable by user
• Status indication (red/green LEDs)
• Simple handling
• Firmware-Updates over a boot loader
PC
mySmartUSB light
AVR
Zielsystem /
target system
5
V
3,3
V
USB 2.0
virtual COM
ISP 6
FLASH, EEP
FUSE
AVR911 oder
STK500v2
USB 5
V
Firmware
*.hex *.eep
*.elf *.bin
Power-
switch