User manual

IN button
Press and release.
(upward movement)
memory 1
Press and hold for 5 seconds.
(The buzzer will sound twice.
The memory is saved as location 1)
memory 2
Press and hold for 5 seconds.
(The buzzer will sound twice.
The memory is saved as location 2)
OUT button
Press and release.
(downward movement)
location 1
Press and release, than press OK.
(The TV wall mount will automatically swivel
to the location 1 after buzzer sounds once)
location 2
Press and release, than press OK.
(The TV wall mount will automatically swivel to the
location 2 after buzzer sounds once)
learn mode
: Stop Button
OK
+
SET
OK
: Learning Button
Remote control operation instructions NOTE: No-load running prohibited.
1. When powered on, the buzzer sounds once beep. TV ceiling mount will be in standby state. The TV ceiling mount is
 installadonaatsurfacebydefault,andhasao°~75°continuousadjustabletilt.(PleaseresetthetiltanglelfyouinstalltheTV
ceiling mount on a pitched surface. Press and hold LOCATION 1 for 5 seconds and repeat four times. The system will automatically
 ndthepositionwithouthumanintervention.Oncethisisdone,thesystemwillautomaticallystopatthemaximumposition.
(Please ignore this step if this mount is not intended for installation on a pitched surface.)
2. Press and release OKtoreturntheTVceilingmountatagainsttheceilingsurfaceandhearonebeepfromthe
buzzer, the system will then enter a working condition.
Manual mode
• ln any positlon (but the minimum position against the ceiling): when manually push up the TV ceiling mount over a distance,
the TV ceiling mount will automatically return back to the minimum position against the ceiling.
• In the minimum position: when manually push up the TV ceiling mount over a little distance, the TV ceiling mount will automatically
 unfoldatthemaximumposition.
LEARN MODE operation instructions
The loss of matched remote control would result in TV ceiling mount being unusable. The learn mode is used to learn how to use
TVremote(OnlysuitablefortheTVremoteofpopularbrands.)tocontrolTVwallmount.
NOTE:
• TVremotecan`treplacetheallfunctionsofmatchedremotecontrol.Onlylearningthethreebuttonsfunctions.
OK, In button and Out button.
• The user must follow the rules below when using the TV remote to control TV ceiling mount.
• Select the alternate buttons from the TV remote, and the button that can`t direct control the TV.
• If you need to erase all the button functions LEARNED, press and hold LOCATION 1 for 4 seconds and repeat 5 times.
lf you don‘t erase them, the new button functions LEARNED every time will overwrite the last button functions LEARNED.
LEARN MODE instructions as shown below
1. Press and hold SET for 5 seconds until LED light on the matched remote control stays on, than press OK. The buzzer will sound
once, the red LED light on the IR receiver will stay on, then the learn mode will be entered.
2. If learn OUT BUTTON, please press OUT BUTTON on the matched remote control until the buzzer sounds twice. The red LED
 lightontheIRreceiverwillchangefrombeingsteadytoaslowash.
3. Aim the TV remote at the IR receiver, and press the button on the TV remote that you need to set as the function of
OUT BUTTONuntilthebuzzersoundsthreetimes.TheredLEDlightontheIRreceiverwillchangefromslowashtoafastash
4. Press OKonthematchedremotecontroluntilthebuzzersoundsfourtimes.TheredLEDlightontheIRreceiverwillturno. 
OUT BUTTON will be learned successfully. If the buzzer only sounds once, then a learn failure. (The TV remote won`t
support the learning function). (Please follow step 1 through step 4 in turn if the user need to LEARN more buttons)
Learn „Power“ button on the TV remote:
Press and hold SET for 5 seconds until LED light on the matched remote control stays on, and then press OK. The buzzer will
sound once, the red LED light on the IR receiver will stay on, then press and hold LOCATION 1 button on the matched remote
control until the buzzer sounds twice, then release the LOCATION 1 button. The red LED light on the IR receiver will change from
beingsteadytoaslowash.AimtheTVremoteattheIRreceiver,andpressPower button. The buzzer will sound three times. The
redLEDlightontheIRreceiverwillchangefromslowashtoafastash.PressOK Button on the matched remote control until
thebuzzersoundsfourtimes.TheredLEDlightontheIRreceiverwillturno.Power button will be Learned successfully. If press
power button, the TV wall mount will automatically reset.
NOTE:Whenthereisnoactivityforover20secondsinanystep,TVremotewillautomaticallyexitfromthelearnmode.
Before power connection, be sure that bracket and the TV installed correctly.
Keep the children away from power.
!