LongReach II Active CCTV Receiver Balun 500124 Installation Guide P/N: 94-000698-A SE-000698-A
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide Copyright Notice: Copyright © 2011 MuxLab Inc. All rights reserved. Printed in Canada. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without prior written permission of the author. Trademarks: MuxLab is a registered trademark of MuxLab Inc.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide Table of Contents 1. Overview ........................................................................4 1.1. Description........................................................4 1.2. Features.............................................................5 2. Technical Specifications ...............................................6 3. Installation Procedure ................................................10 3.1. Pre-Installation Checklist .
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide 1. Overview 1.1. Description The LongReach II Active CCTV Receiver Balun (500124) allows one (1) analog CCTV video signal to be transmitted up to 1 mile (1.6 km) via a Category 5e/6 twisted pair cable when used in conjunction with MuxLab’s passive CCTV baluns (i.e. 500000, 500009, 500024) at the camera end. The 500124 features Automatic Gain Control (AGC) and Ground Loop Isolation (GLI) for reliable and stable image quality.
© MuxLab. 1.2.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide 2. Technical Specifications Specifications Environment CCTV composite baseband video; NTSC, PAL, SECAM Devices CCTV cameras, monitors, DVR, switchers, IP encoders, and other CCTV equip. Transmission Transparent to the user Video Bandwidth 20 Hz to 8 MHz. Input 1.5 Vp-p max, 100Ω, balanced (RJ45) Output 1.1 Vp-p, ± 1 dB, 75Ω, unbalanced (BNC) Insertion Loss -14 dB minimum for luma, -60 dB minimum for chroma.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide Remote Power (i.e.; 24 VAC, 28 VAC) Wiring Remote low voltage power supported via two (2) twisted pairs. A Class II power supply is recommended. Max. Current 2.5 A rms or DC Max. Distance @ 24VAC via three twisted pairs. *Longer distances may be achieved @ 28 VAC. 2 VA: 1,500 ft (457m)* 4 VA:745ft (227m)* 10 VA: 300 ft (91m)* (46m)* 20 VA: 150 ft *Based on 10% voltage drop at camera. Please consult your CCTV vendor for more info.
© MuxLab.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide Specifications (Cont’d) Enclosure ABS fire retardant plastic Dimensions 2.40” x 2.25” x 1.0” (6.1 x 5.7 x 2.54 cm) Weight 3.0 oz (85 gms) Regulatory FCC and CE.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide 3. Installation Procedure 3.1. Pre-Installation Checklist The LongReach II Active CCTV Receiver Balun (500124) is used to provide extended distance via a copper twisted pair. Before installing the product, please verify the following checklist to ensure that installation takes place smoothly. 1. The 500124 is always connected to the receiver side of a CCTV installation.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide 4. The 500124 must be powered by a 5V DC, 6 W floating (non-grounded Ring of the PSU DC plug) power supply (supplied with the product). 5. The 500124 is calibrated to work with CCTV sources that conform to RS-343 (RS-170).
© MuxLab. 3.2. LongReach II Active CCTV Receiver Balun Installation Guide Installation Procedure 1. Connect the passive CCTV Balun (500000 or 500009) to the CCTV camera video output port. 2. Connect one twisted pair to the passive CCTV Balun. If the balun is the 500009, use a small flathead screwdriver. If the balun is the 500000, crimp RJ45 modular plug to the end of the cable, ensuring that Pins 7 & 8 of the RJ45 are connected to a twisted pair. 3.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide 4. If remote power, video and PTZ control is to be transmitted, use 500022 balun. Refer to the specification table regarding maximum distances and set the slide switch on the 500124 to “500022”. Using camera specific PSU connect respective terminals on either side. 5. Ensure that the power is off on the DVR and then connect the 500124 to the appropriate video input port. 6. Connect the plug from the 5 VDC power supply.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide 8. Power on the CCTV system. When a video signal is detected, the AGC Lock LED on the 500124 will change from OFF to ON. 9. Due to the Automatic Gain Control of the Active Balun, the camera image may take a few seconds to stabilize. This is normal. The 500124 automatically restores the video camera signal to its original quality, compensating for effects due to the presence of a UTP cable and electrical noise.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide 12. The following configuration. diagram illustrates a typical 13. The 500124 is equipped with resettable fuses to protect the circuitry. In the event of a power surge, the fuse(s) will trip and the green LED will dim. In order for the fuse(s) to reset, the power to the 500124 must be turned OFF for 2-3 minutes. The fuse(s) will then reset and the power can be turned on again.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide 4. Troubleshooting The following table describes some of problem symptoms, probable causes, and possible solutions. If the information below does not solve the problem, the technical support contact information can be found at the end of this section.
© MuxLab. 4.1. LongReach II Active CCTV Receiver Balun Installation Guide Technical Support Information When contacting your nearest MuxLab dealer or MuxLab Technical Support, please have the following information ready: • Unit model number • Cabling layout.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide 5. Product Warranty Policy Items Under Warranty - Company Policy MuxLab guarantees its products to be free of defects in manufacturing and workmanship for the warranty period from the date of purchase. If this product fails to give satisfactory performance during this warranty period, MuxLab will either repair or replace this product at no additional charge, except as set forth below.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide Warranty Periods Any product found to be defective within three (3) months of invoice, including one (1) month shelf life, may be returned for replacement by a new unit or a satisfactory repair within one (1) month of receiving any returned product. The customer must provide MuxLab with the serial number and proof of purchase of the defective unit being returned. All R.M.A.
© MuxLab. LongReach II Active CCTV Receiver Balun Installation Guide MuxLab Inc. 8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5 Tel: (514) 905-0588 Fax: (514) 905-0589 Toll Free (North America): (877) 689-5228 E-mail: videoease@muxlab.com URL: www.muxlab.
