Table of Contents Introduction Instrument Cluster 4 12 Warning lights and chimes Gauges Message center 12 17 19 Entertainment Systems 29 Auxiliary input jack (Line in) USB port Satellite radio information Navigation system SYNC威 Climate Controls Manual heating and air conditioning Navigation system based climate control Rear window defroster Lights Headlamps Turn signal control Interior lamps Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mi
Table of Contents Seating and Safety Restraints Seating Personal Safety System™ Safety belt system Airbags Child restraints Tires, Wheels and Loading Tire information Tire inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving Starting Brakes AdvanceTrac威 Transmission operation Reverse sensing system Rear-view camera system Roadside Emergencies Getting roadside assistance Hazard flasher control Fuel pump shut-off Fuses and relays Changing tires Tempora
Table of Contents Cleaning 270 Maintenance and Specifications 278 Engine compartment Engine oil Battery Engine coolant Fuel information Air filter(s) Part numbers Maintenance product specifications and capacities Engine data 280 283 287 289 295 309 312 313 316 Accessories 320 Ford Extended Service Plan 323 Scheduled Maintenance 327 Normal scheduled maintenance and log Index 333 345 The information contained in this publication was correct at the time of going to print.
Introduction CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the following website: • In the United States: www.ford.com • In Canada: www.ford.ca • In Australia: www.ford.com.au • In Mexico: www.ford.com.
Introduction Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps toward this aim. Information in this respect is highlighted in this guide with the tree symbol.
Introduction Drive your new vehicle at least 100 miles (160 km) before performing extended wide open throttle maneuvers and at least 1,000 miles (1,600 km) before towing a trailer or before performance/competition conditions. For more detailed information about towing a trailer, refer to Trailer towing in the Tires, Wheels and Loading chapter. Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating.
Introduction your vehicle. For U.S. only (if equipped), if you choose to use the SYNC威 Vehicle Health Report, you consent that certain diagnostic information may also be accessed electronically by Ford Motor Company and Ford authorized service facilities, and that the diagnostic information may be used for any purpose. See your SYNC威 supplement for more information. Event Data Recording This vehicle is equipped with an event data recorder (EDR).
Introduction To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have such special equipment, can read the information if they have access to the vehicle or the EDR.
Introduction CELL PHONE USE The use of mobile communications equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment. Mobile communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Service Engine Soon Engine Air Filter Passenger Compartment Air Filter Jack Check Fuel Cap Low Tire Pressure Warning MAX MIN
Instrument Cluster WARNING LIGHTS AND CHIMES Base V6 engine instrument cluster (standard measure shown, metric similar) OFF Optional V6 and GT instrument cluster (standard measure shown, metric similar) OFF Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work.
Instrument Cluster Service engine soon: The service engine soon indicator light illuminates when the ignition is first turned to the on position to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the service engine soon light will stay on until the engine is cranked, then turn itself off if no malfunctions are present.
Instrument Cluster WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Contact your authorized dealer as soon as possible. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury. Anti-lock brake system (if equipped): If the ABS light stays ABS illuminated or continues to flash, a malfunction has been detected.
Instrument Cluster Engine coolant temperature: Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible, switch off the engine and let cool. Refer to Engine coolant in the Maintenance and Specifications chapter. WARNING: Never remove the coolant reservoir cap while the engine is running or hot. Low tire pressure warning: Illuminates when your tire pressure is low. If the light remains on at start up or while driving, the tire pressure should be checked.
Instrument Cluster Speed control: Illuminates when the speed control is engaged. Turns off when the speed control system is disengaged. Door ajar: Illuminates when the ignition is in the on position and any of the doors or the hood/trunk are not completely closed. Anti-theft system: Flashes when the SecuriLock威 passive anti-theft system has been activated. Electronic throttle control: Illuminates when the engine has defaulted to a “limp-home” operation. Contact your authorized dealer as soon as possible.
Instrument Cluster GAUGES Base V6 engine instrument cluster (standard measure shown, metric similar) 1 2 3 4 17 2012 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)
Instrument Cluster Optional V6 and GT instrument cluster (standard measure shown, metric similar) 1 2 6 3 4 5 Refer to Message center in this chapter to select preset colors or user definable colors (MyColor威) for the nighttime gauge backlighting. 1. Speedometer: Indicates the current vehicle speed. 2. Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the on position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade.
Instrument Cluster 5. Engine oil pressure gauge (optional V6 and GT cluster only): Indicates engine oil pressure. The needle should stay in the normal operating range (between L and H). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. Add oil if needed. If the oil level is correct, have your vehicle checked at your authorized dealer. Battery voltage gauge (optional V6 and GT cluster only): 6.
Instrument Cluster MYKEY MILES (km) For more information, refer to MyKey威 in the Locks and Security chapter. MILES (km) TO E This displays an estimate of approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to correctly detect the added fuel. LOW FUEL LEVEL will display when you have approximately 50 miles (80 km) to empty. Press RESET to clear this warning message.
Instrument Cluster MPG (L/km) This displays instantaneous fuel economy as a bar graph ranging from ↓ poor economy to ↑ excellent economy. Your vehicle must be moving to calculate instantaneous fuel economy. When your vehicle is not moving, this function shows ↓, one or no bars illuminated. Instantaneous fuel economy cannot be reset. TIMER Timer displays the trip elapsed drive time. To operate, do the following: 1. Press and release RESET in order to start the timer. 2.
Instrument Cluster 7. MYKEY DISTANCE (if MyKey威 is programmed) 8. MYKEY(S) PROGRAMMED 9. ADMIN KEYS PROGRAMMED Note: Some systems show a message only if a condition is present. OIL LIFE This displays the remaining oil life. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change perform the following: 1.
Instrument Cluster Press and hold RESET to turn the feature on or off. AMBIENT DIM Use this to adjust the brightness of the ambient lighting. Press RESET to choose the various settings. GAUGE COLOR, AMBIENT COLOR, HALO COLOR GAUGE COLOR: The instrument cluster gauges are backlit with white backlighting when the headlamps are off. When the headlamps are on, you can select one of the preset colors for the nighttime gauge backlighting or create up to three custom colors using the MyColor威 feature.
Instrument Cluster To enter the MyColor威 adjust mode, do the following (vehicle must be stationary): 1. Press and hold RESET for three seconds at the MyColor 1, 2 or 3 menu option to reach the MyColor威 adjust mode. 2. Press SETUP to scroll through the R (red), G (green), B (blue) and Exit options. 3. Press RESET to blend in more of the color being adjusted. 4. To save and exit, hold RESET for three seconds when prompted. Pressing RESET for less than three seconds will cycle back through the colors.
Instrument Cluster CREATE MYKEY / MYKEY SETUP/ CLEAR MYKEY For more information refer to MyKey威 in the Locks and Security chapter. LANGUAGE = ENGLISH / SPANISH / FRENCH Allows you to choose which language the message center will display in. Selectable languages are English, Spanish, or French. Waiting four seconds or pressing the RESET button cycles the message center through each of the language choices. Press and hold RESET for two seconds to set the language choice.
Instrument Cluster CHECK FUEL FILL INLET — Displayed when the fuel fill inlet may not be properly closed. Refer to Easy Fuel威 “no cap” fuel system in the Maintenance and Specifications chapter. CHECK CHARGING SYSTEM — Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible.
Instrument Cluster SERVICE ADVANCETRAC — Displayed when the AdvanceTrac威 system has detected a condition that requires service. ENGINE OIL CHANGE SOON — Displayed when the engine oil life remaining is 10% or less. OIL CHANGE REQUIRED — Displayed when the oil life left reaches 0%. TO STOP ALARM START VEHICLE — Displayed when the perimeter alarm system is armed and the vehicle is entered using the key on the driver’s side door.
Instrument Cluster TOP SPEED MYKEY SETTING — Displayed when a MyKey威 is in use and the MyKey speed limit is on and the vehicle speed is 80 mph (130 km/h). Refer to MyKey威 in the Locks and Security chapter for more information. BUCKLE UP TO UNMUTE AUDIO — Displayed when a MyKey威 is in use and Belt-Minder威 is activated. Refer to MyKey威 in the Locks and Security chapter for more information.
Entertainment Systems AUDIO SYSTEMS AM/FM Single CD/MP3 satellite-compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle.
Entertainment Systems AM/FM radio / VOL (Power/Volume): Press to turn the radio on/off. Turn the knob to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a nominal listening level when the ignition switch is turned back on. AM/FM: Press repeatedly to select AM/FM1/FM2 frequency band. TUNE: Turn the knob to go up/down the frequency band in individual increments.
Entertainment Systems initiate or press OK to immediately initiate the search. If you press another control within those five seconds, the search will not initiate. The 10 strongest stations will be filled and the station stored in preset 1 will begin playing. If there are fewer than 10 strong stations, the system will store the last one in the remaining presets. Note: In order to re-run the autoset features, you must first select AUTO PRESET OFF and press OK. Then, select AUTO PRESET ON and press OK.
Entertainment Systems LOAD: This control is not operational. To load a CD, simply insert the disc, label side up, into the CD slot. / Play/Pause: Press to play/pause a track when playing a CD. EJECT: Press to eject the CD. SEEK to SEEK: Press access the previous/next track. CAT (Category) / FOLD (Folder): In MP3 mode only– Press SEEK to access the previous/next CAT/FOLD and then press folder. SCAN: Press for a brief sampling of all tracks on the current disc or MP3 folder. DIRECT: In CD mode– Press DIRECT.
Entertainment Systems In TEXT MODE: Sometimes the display requires additional text to be displayed. When the < / > indicator is active, press TEXT and then SEEK to view the additional display text. press COMPRESSION: Press MENU repeatedly until COMPRESSION ON/OFF SEEK to switch between ON/OFF. appears in the display. Use When COMPRESSION is ON, the system will bring the soft and loud CD passages together for a more consistent listening level.
Entertainment Systems SEEK: Press SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.), SEEK to seek to the previous/next channel in the selected press SEEK to fast seek through the category. Press and hold previous/next channels. SCAN: Press SCAN for a brief sampling of all available SIRIUS威 satellite channels. If a specific category is selected, (Jazz, Rock, News, etc.
Entertainment Systems SATELLITE RADIO MENU: Press MENU when satellite radio mode is active to access. Press OK to enter SEEK to cycle through the into the satellite radio menu. Press following options: • CATEGORY MENU- Press OK to enter category mode. SEEK to scroll through the list of available SIRIUS威 Press channel Categories (Pop, Rock, News, etc.) Press OK when the desired category appears in the display. After a category is selected, SEEK to search for that specific category of channels press only (i.
Entertainment Systems c. DELETE ALL SONGS?: Press OK to delete all song’s from the system’s memory. The display will read ARE YOU SURE? Press OK to confirm deletion of all saved songs and the display will read ALL DELETED. Note: If there are no songs presently saved, the display will read NO SONGS. d. DISABLE ALERTS/ENABLE ALERTS?: Press OK to enable/disable the satellite alert status which alerts you when your selected songs are playing on a satellite radio channel. (The system default is disabled.
Entertainment Systems d. RESET PIN: Press OK when RESET PIN is displayed. The display will read ARE YOUR SURE. Press OK again to automatically reset the PIN to its initial password setting (1234). PIN RESET TO DEFAULT PIN will be displayed. e. RETURN: Press OK when RETURN is displayed and the system will exit back to the satellite radio menu. Sound adjustments Press SOUND repeatedly to cycle through the following features: • Shaker mode (if equipped): Press mode on/off. • BASS: Press TUNE knob.
Entertainment Systems Extra features AUX: Press repeatedly to cycle through LINE (auxiliary audio mode) and SYNC威 (if equipped). For auxiliary jack location and further information on auxiliary audio mode, refer to Auxiliary input jack later in this chapter. If your vehicle is equipped with SYNC威, please refer to the SYNC威 information included with your vehicle for further information. / Play/Pause: Press this control to play or pause the current CD.
Entertainment Systems Your vehicle is equipped with an auxiliary input jack (AIJ) located in the center console. The auxiliary input jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity. To achieve optimal performance, please observe the following instructions when attaching your portable music device to the audio system.
Entertainment Systems 7. Adjust the sound on your portable music player until it reaches the level of the FM station or CD by switching back and forth between the AUX and FM or CD controls. Troubleshooting: 1. Do not connect the audio input jack to a line level output. Line level outputs are intended for connection to a home stereo and are not compatible with the AIJ. The AIJ will only work correctly with devices that have a headphone output with a volume control. 2.
Entertainment Systems Your vehicle may be equipped with a USB port inside your center console. This feature allows you to plug in media playing devices, memory sticks, and also to charge devices if they support this feature. For further information on this feature, refer to Accessing and using your USB port in the SYNC威 supplement or Navigation System supplement.
Entertainment Systems CD/CD player care Do: • Handle discs by their edges only. (Never touch the playing surface). • Inspect discs before playing. • Clean only with an approved CD cleaner. • Wipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only.
Entertainment Systems CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pens may damage CDs. Please contact your authorized dealer for further information. Audio system warranty and service Refer to the Warranty Guide for audio system warranty information.
Entertainment Systems Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extension will be played. Other files will be ignored by the system. This enables you to use the same MP3 disc for a variety of tasks on your work computer, home computer and your in-vehicle system. 1 .mp3 1 .mp3 2 2 3 .mp3 3 .mp3 4 .
Entertainment Systems • Terrain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your reception. • Station overload: When you pass a ground based broadcast repeating tower, a stronger signal may overtake a weaker one and result in an audio mute. Unlike AM/FM audible static, you will hear an audio mute when there is a satellite radio signal interference.
Entertainment Systems Radio Display ACQUIRING SAT FAULT INVALID CHNL UNSUBSCRIBED NO TEXT NO TEXT NO TEXT Condition Action Required Radio requires more No action required. than two seconds to This message should produce audio for the disappear shortly. selected channel. Internal module or If this message does system failure not clear within a short present. period of time, or with an ignition key cycle, your receiver may have a fault. See your authorized dealer for service.
Entertainment Systems Radio Display NO SIGNAL Condition Loss of signal from the SIRIUS威 satellite or SIRIUS威 tower to the vehicle antenna. UPDATING Update of channel programming in progress. Satellite service has been deactivated by SIRIUS威 satellite radio. CALL SIRIUS威 1–888–539–7474 Action Required You are in a location that is blocking the SIRIUS威 signal (i.e., tunnel, under an overpass, dense foliage, etc). The system is working properly. When you move into an open area, the signal should return.
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear the windshield of fog and thin ice. The system will automatically provide outside air to reduce window fogging. Press this button again to return to the previous air flow selection. 2.
Climate Controls 5. Recirculated air: Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time needed to cool down the interior of the vehicle and may also help reduce undesired odors from reaching the interior of the vehicle. Recirculated air engages automatically when MAX A/C is selected or can be engaged manually in any airflow mode except (defrost).
Climate Controls • To improve the A/C cool down, drive with the windows slightly open for 2-3 minutes after start up or until the vehicle has been “aired out.” • A small amount of air may be felt from the floor vent regardless of the air distribution setting that is selected.
Climate Controls DUAL ZONE AUTOMATIC TEMPERATURE CONTROL (NAVIGATION-BASED) (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. CLIMATE: Press to control the climate control system through the touch display screen. See Touchscreen functions later in this section. 2. R Rear defroster (if equipped): Press to activate/deactivate the rear window defroster.
Climate Controls 5. Passenger heated seat (if equipped): Press to control the passenger heated seat. Refer to Heated seats in the Seating and Safety Restraints chapter for more information. Recirculated air: Press to activate/deactivate air recirculation in 6. the vehicle. Recirculated air may reduce the amount of time needed to cool down the interior of the vehicle when used with A/C and may also help reduce undesired odors from reaching the interior of the vehicle.
Climate Controls TOUCHSCREEN FUNCTIONS Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. Temperature: Press the up and down arrows on the left side of the screen to increase/decrease the airflow temperature for the driver side of the vehicle. This control also adjusts the passenger side temperature when dual zone operation is disengaged.
Climate Controls Operating tips • To reduce fog build-up on the windshield during humid weather, select (defrost). Temperature and/or fan speed can also be increased to improve clearing. • To reduce humidity build-up inside the vehicle: do not drive with the system off or with (recirculated air) engaged. • Do not put objects under the front seats that will interfere with the airflow to the back seats. • Remove any snow, ice or leaves from the air intake area at the base of the windshield.
Climate Controls REAR WINDOW DEFROSTER R Press the control to clear the rear window of thin ice and fog. The LED will illuminate. The rear window defroster turns off automatically after 15 minutes, or when the ignition is turned off. To manually turn off the defroster before 15 minutes have passed, press the control again. The vehicle must be running to use this feature.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the low beam headlamps on. Automatic instrumentation illumination A light sensor in your vehicle monitors the outside lighting conditions and automatically sets the instrument panel illumination to one of the following modes: • If the headlamps and parking lamps are off, the vehicle will be in daytime illumination mode.
Lights The autolamp system also keeps the lights on for a predetermined amount of time after the ignition switch is turned to off. You can change the amount of time the lamps stay on by using the programming procedure that follows: Note: If the vehicle is equipped with autolamps, it will have the headlamps on with windshield wipers feature. If the windshield wipers are turned on, the exterior lamps will turn on with the headlamp control in the autolamp position.
Lights High beams • Push the lever toward the instrument panel to activate. • Pull the lever toward you to deactivate. OFF Flash-to-pass Pull toward you, to the first detent, to activate and release to deactivate. Note: Vehicles equipped with HID headlamps will hear an audible click when activating this feature.
Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parking lamp operation. • Move the control to the full upright position, past detent, to turn on the interior lamps. • Move the control down, past detent, to turn off the interior lights. • Move the control to the full downward position, to dim the interior lights to their minimum. The instrument panel/switch lighting will remain lit.
Lights Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well).
Lights 4. Locate the vertical adjuster on each headlamp. • Halogen headlamp (1) • HID headlamp (2) 5. Then use a 7 mm Allen wrench or a Phillips screwdriver to adjust the headlamp up or down. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE. 6. Close the hood and turn off the lamps. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal.
Lights INTERIOR LAMPS Dome/Map lamps The dome lamp lights when:. • any door is opened. • any of the remote entry controls are pressed and the ignition is off. • the instrument panel dimmer switch is rotated up, past the detent, until the courtesy lamps come on. The map lamps are activated by pressing the controls on either side of the lamp. BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design.
Lights BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Lights Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in the off position, then open the hood. 2. Disconnect the electrical connector from the bulb by depressing the retainer clip and pulling rearward. 3. Remove the bulb by rotating it counterclockwise and pulling it straight out. WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Lights Replacing front parking lamp/turn signal bulbs 1. Make sure the headlamp control is in the off position and open the hood. Halogen headlamp HID headlamp 2. Remove the hex head screws attaching the underbody forward aeroshield and remove to gain access to the front parking lamp/turn signal assembly. 3. Rotate the socket counterclockwise and remove from the lamp assembly. 4. Carefully pull the bulb straight out of socket. Install the new bulb in reverse order.
Lights Replacing front sidemarker bulb 1. Make sure the headlamp control is in the off position. 2. Remove the hex head screws attaching the underbody forward aeroshield and remove to gain access to the front sidemarker assembly. 3. Rotate the socket counterclockwise and remove from the lamp assembly. 4. Carefully pull the bulb straight out of socket. Replacing tail lamp/brake/rear turn signal lamps See your authorized dealer for replacement LED assembly.
Lights 3. Unbolt the three tail lamp attachment nuts and remove the lamp assembly. 4. Rotate the LED assembly counterclockwise and remove it from the lamp assembly. 5. Disconnect the LED assembly from the electrical connector and replace the LED assembly. 6. Install new LED assembly in reverse order. Replacing backup bulbs The backup lamps are located in the tail lamp assembly. Follow the same steps to replace either bulb. 1. Make sure the headlamp switch is in the off position, then open the trunk. 2.
Lights Replacing rear sidemarker lamp bulbs 1. Make sure the headlamp switch is in the off position and locate the sidemarker on the rear bumper fascia. 2. Insert a flathead screwdriver between the rear of the sidemarker lens and the bumper fascia. 3. Push the screwdriver to the front of the vehicle and then slide it towards you to pop out the lamp assembly. 4. Carefully pull the bulb straight out of socket. Install the new bulb in reverse order. Replacing fog lamp bulbs (GT) (if equipped) 1.
Lights Replacing fog lamp bulbs (GT-CS) (if equipped) 1. Make sure the headlamp control is in the off position and open the hood. 2. Remove the underbody air deflector panel screws and panel. 3. Disconnect the electrical connector from the bulb by pulling it straight off. 4. Rotate the bulb counterclockwise and remove from the lamp assembly. Install the new bulb in reverse order. Replacing fog lamp bulbs (V6) (if equipped) 1. Make sure the headlamp control is in the off position and open the hood. 2.
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick press and hold: the wipers will swipe three times with washer fluid. • a long press and hold: the wipers and washer fluid will be activated for up to ten seconds.
Driver Controls TILT STEERING WHEEL To adjust the steering wheel: 1. Hold the steering wheel with one hand. With the other hand, push the lever down to unlock the steering column. 2. Tilt the steering column to its desired position. 3. While holding the steering wheel, pull the lever up to its original position to lock the steering column. WARNING: Never adjust the steering wheel when the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp.
Driver Controls Flexible visor storage system (if equipped) Visors equipped with the flexible visor storage system can accommodate various storage accessories. A sunglass clip and multi-function clip are provided. To attach one of the accessories, do the following: 1. Insert the provided removal tool (on the accessory holder) or a coin into the slot on the plug and turn 1/4-turn in either direction to remove. It may be necessary to rotate the visor until the plug drops away from the opening.
Driver Controls Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Turn ignition to the on position. 3 2 15 1 4 14 13 5 12 6 7 8 9 1011 3. Press and hold the 7 and 9 radio preset buttons together for approximately five seconds until ZONE XX appears in the CID. 4. Press and release the 7 and 9 radio preset buttons together, repeatedly until ZONE XX changes to the correct zone (1–15) in the CID. 5.
Driver Controls 2. To calibrate, press and hold the 7 and 9 radio preset buttons together for approximately 10 seconds until CAL appears. Release the buttons. 3. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CAL display changes to the direction value (N, S, E, W, etc.). It may take up to five circles to complete calibration. 4. The compass is now calibrated. CENTER CONSOLE Your vehicle is equipped with a variety of console features.
Driver Controls AUXILIARY POWER POINT (12V DC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.
Driver Controls WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and pull the switches to open and close windows. • Press down (to the first detent) and hold the switch to open. • Pull up (to the first detent) and hold the switch to close.
Driver Controls Bounce-back override (front windows only) To override bounce-back, within two seconds after reaching bounce-back position, if the switch is moved from the neutral to the one-touch up position the window will travel up with no bounce-back protection. If the switch is released before the window reaches fully closed position, the window will stop. For example: bounce-back override can be used to overcome the resistance of ice on the window or seals.
Driver Controls Rear power windows manual override (convertible only) The rear quarter window switch will not operate under the following conditions: • Convertible top is moving • Convertible top is not completely up or down In the event that the rear quarter window switch does not operate when the convertible top is completely up or down, the rear quarter windows can be manually raised up. The following procedure must be performed within two minutes: 1.
Driver Controls Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance. Note: A rear center passenger and/or raised rear center headrest (if equipped) may also block the light from reaching the sensor. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.
Driver Controls Using speed controls The speed controls are located on the steering wheel. The following buttons work with speed control: Base controls OFF ON SET RES Optional controls SET RESUME SET OFF ON ON/OFF: Press to turn the system on or off. SET (+): Press to set a speed or to increase a set speed. SET (–): Press to decrease a set speed. RES / RESUME: Press to resume a set speed. Setting speed control The set speed control: 1. Press and release ON. 2. Accelerate to the desired speed. 3.
Driver Controls Disengaging speed control To disengage the speed control, tap the brake pedal or clutch pedal (if equipped). Disengaging the speed control will not erase previous set speed. Resuming a set speed Press and release RES / RESUME. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control To increase the set speed: • Press and hold SET (+) until you get to the desired speed, then release.
Driver Controls STEERING WHEEL CONTROLS (IF EQUIPPED) With navigation system (if equipped) to use the voice • Press command features. For further information on using voice commands with the navigation system, refer to the Navigation System supplement. to select the entertainment playing media (radio, CD, line in, • Press etc.). • Press – VOL + to adjust the volume in any mode. • Press to activate phone mode. Refer to the Navigation System supplement for more information on using phone features.
Driver Controls • Press OK to confirm selections various audio and SYNC威 selections. For further information on the SYNC威 system, refer to the SYNC威 supplement. • Press to change radio stations/CD tracks. UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED) Your vehicle may be equipped with a universal garage door opener which can be used to replace the common hand-held transmitter.
Driver Controls Additional Car2U威 system information can be found on-line at www.learcar2U.com or by calling the toll-free Car2U威 system help line at 1-866-572-2728. Types of garage door openers (rolling code and fixed code) The Car2U威 Home Automation System may be programmed to operate rolling code and fixed code garage door openers. • Rolling code garage door openers were produced after 1996 and are code protected.
Driver Controls Note: Do not program the Car2U威 system with the vehicle in the garage. Make sure that your key is on and engine off while programming the transmitter. 1. Firmly press the two outer Car2U威 system buttons for 1–2 seconds, then release. 2. Go to the garage to locate the garage door opener motor and its “learn” button. You may need a ladder to reach the unit and you may need to remove the unit’s cover or light lens to locate the “learn” button.
Driver Controls After successful programming, you will be able to operate your Car2U威 system by pressing the button you programmed to activate the opener. The indicator light above the selected button will turn on to confirm that the Car2U威 system is responding to the button command.
Driver Controls Switch position 1 2 3 4 Up, on L L L L or + Middle, neutral M M M M or 0 Down, R R R R off or – L=left; M=middle; R=right 5 6 7 8 9 10 11 12 L L L L L L L L M M M M M M M M R R R R R R R R 3. To input these positions into the Car2U威 system, simultaneously press all three Car2U威 system buttons for a few seconds and then release to put the device into programming mode. The indicator lights will blink slowly. Within 2.
Driver Controls After successful programming, you will be able to operate your Car2U威 system by pressing the button you programmed to activate the opener. The indicator light above the selected button will turn on to confirm that the Car2U威 system is responding to the button command. Erasing the Car2U姞 Home Automation System buttons Note: The system allows for three devices to be programmed.
Driver Controls POSITIVE RETENTION FLOOR MAT WARNING: Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured to retention posts so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. • Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
Driver Controls WARNING (Continued) • Failure to properly follow floor mat installation or attachment instructions can potentially cause interference with pedal operation causing loss of control of vehicle. • To install floor mats, position the floor mat so that the eyelet is over the retention post and press down to lock in. • To remove the floor mat, reverse the installation procedure. CONVERTIBLE (IF EQUIPPED) Do not store articles behind rear seat.
Driver Controls Note: The latch handles must be pulled downward fully to allow the latch to fully rotate into the open position. 3. Unclamp the top from the windshield header by pulling each latch handle down and then rotating the latch to the rear until it clears the header. Note: If the top has not been lowered for some time and sticks to the windshield header, push the front of the top up slightly with your hand to loosen it. 4.
Driver Controls Installation of the boot (if equipped) Be sure the boot is secure on the vehicle before driving. 1 5 2 4 3 1. Install the boot on the vehicle by hooking the boot retaining clips on the back panel. 2. Install the boot on the right side tucking in the front part of the boot in the quarter panel and hooking the retaining clip on the side. 3. Install the boot on the left side tucking in the front part of the boot in the quarter panel and hooking the retaining clip on the side. 4.
Driver Controls Storing the boot 1. Position the boot right-side up and fold each side of the boot inward. 2. Turn the boot upside down and fold the left side of the boot inward. 3. Fold the right side inward and secure the boot with the strap. Stow the boot in the trunk. Raising the convertible top The convertible top will not operate unless the vehicle is traveling under 3 mph (5 km/h).
Driver Controls To raise the convertible top: 1. Bring the vehicle to a complete stop. Key must be in the on position. It is recommended that the vehicle’s engine is running when raising the top to prevent draining the battery. 2. Press the convertible top switch, holding it until the windows lower completely and the top unfolds and moves forward toward the windshield header. 3. You can release the convertible top switch to open both latch handles before the top meets the windshield header.
Driver Controls ROLLER BLIND SUN SHADE (IF EQUIPPED) If your vehicle is equipped with a glass roof, the roller blind sun shade will cover the glass roof inside your vehicle. Use the center-mounted cup handle to slide the shade open or closed. INTERIOR TRUNK CONTROL The remote trunk release button is located on the instrument panel. Press the button to unlatch the trunk.
Locks and Security KEYS Your vehicle may be equipped with two integrated keyhead transmitters (IKTs). The key blade functions as a programmed key which starts the vehicle and unlocks/locks all the doors. The transmitter portion functions as the remote entry transmitter. Your IKTs are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied IKTs, replacement IKTs are available through your authorized dealer.
Locks and Security MYKEY姞 The MyKey威 feature allows you to program a restricted driving mode to promote good driving habits. All but one of the keys programmed to the vehicle can be activated as a MyKey威. The key will remain restricted until MyKey威 is cleared. Any remaining keys are referred to as an “administrator key” or admin key. The admin key can be used to create a MyKey威, program optional MyKey威 settings, and clear the MyKey威 feature.
Locks and Security Create a MyKey威 To program MyKey威 on one of the keys programmed to the vehicle, insert the key that you want to make a MyKey威 into the ignition. For vehicles equipped with push button start, put the intelligent access key in the backup slot; see the Driving chapter for the location of the backup slot. Turn the ignition on. Use the message center buttons to do the following: 1. Press SETUP until PRESS RESET TO CREATE MYKEY is displayed. 2. Press and release the RESET button.
Locks and Security 5. Press SETUP to enter your choice. The next optional setting will be displayed. 6. Repeat Steps 4 and 5 until you are done changing the optional settings. Clear MyKey威 To reset all MyKeys威 as admin keys, do the following: 1. Turn the vehicle on using the admin key. 2. Press SETUP until PRESS RESET TO CLEAR MYKEY is displayed. 3. Press and release the RESET button. HOLD RESET TO CONFIRM CLEAR is displayed. 4.
Locks and Security Vehicles equipped with traditional keys: When using a Ford-approved remote start system, the default settings will recognize the remote start system as an additional admin key with its associated privileges. Owners of vehicles equipped with traditional keys should program the remote start system as a MyKey威 in addition to the key that they have already programmed as a MyKey威. To program the remote start system as MyKey威, do the following: 1. Enter the vehicle and close all doors. 2.
Locks and Security Troubleshooting Condition Can’t create a MyKey威 Cannot program the MyKey威 optional settings Cannot clear MyKey威 Potential Causes • Key in the ignition is already a MyKey威. • Key in the ignition is the last remaining admin key (there always has to be at least one admin key). • Intelligent access key (if equipped) not in the backup slot — for vehicles with push button start. •SecuriLock威 Passive Anti-Theft System is disabled or in unlimited mode.
Locks and Security Condition Lost the only admin key Lost any key I accidentally programmed all keys as MyKeys威 No MyKey威 function with intelligent access key (push button start) (if equipped) MyKey威 programmed total includes one additional key Admin keys programmed total includes one additional key MyKey威 miles do not accumulate Potential Causes • Purchase a new key from your authorized dealer. • For programming spare keys, refer to the Programming spare keys section in this chapter.
Locks and Security Press the doors. control to unlock all Press the doors. control to lock all Locking and unlocking with keys Your vehicle’s keys are designed to lock and unlock the driver’s door, as well as open the trunk. • The driver’s door is unlocked when the key is inserted in the driver door key cylinder and turned to the unlock position. The driver’s door is locked when the key is inserted in the driver door key cylinder and turned to the lock position.
Locks and Security The autolock feature repeats when: • any door is opened then closed while the ignition is in the on position and the vehicle speed is 9 mph (15 km/h) or lower, and • the vehicle attains a speed greater than 12 mph (20 km/h). Deactivating/activating autolock Your vehicle comes with the autolock feature enabled.
Locks and Security 8. Turn the ignition to the off position. The horn will chirp once to confirm the procedure is complete.
Locks and Security 6. To enable/disable the autounlock feature, press the lock control, then press the unlock control. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated. 7. Turn the ignition to the off position. The horn will chirp once to confirm the procedure is complete.
Locks and Security WARNING: Do not leave children, unreliable adults, or animals unattended in the vehicle. On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people or animals to these high temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.
Locks and Security The IKT allows you to: • remotely unlock the vehicle doors. • remotely lock all the vehicle doors. • remotely open the trunk. • activate the personal alarm. • arm and disarm the active anti-theft system. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition position except while the key is held in the start position. The panic feature operates with the key in the off position.
Locks and Security Two-stage unlocking may be disabled or re-enabled by simultaneously and controls on the IKT for four seconds (disabling pressing the two stage unlock allows all vehicle doors to unlock simultaneously). The turn lamps will flash twice to indicate that two-stage unlock was enabled or disabled. Locking the doors 1. Press and release to lock all the doors. The turn signal lamps will illuminate.
Locks and Security Opening the trunk twice to open the trunk. Press • Ensure that the trunk is closed and latched before driving your vehicle. Failure to properly latch the trunk may cause objects to fall out or block the driver’s rear view. The remote entry system allows you to open the trunk while the ignition is in any position. However, if the ignition is in the on position and the vehicle is in motion, the trunk will not open if the vehicle is moving 3 mph (5 km/h) or faster.
Locks and Security 5. Snap the battery cover back onto the key. Note: Replacement of the battery will not cause the IKT or IA key to become de-programmed from your vehicle. They should operate normally after battery replacement.
Locks and Security Battery saver The battery saver will shut off the interior lamps 10 minutes after the ignition has been turned to the off position and a door is left open, and in 30 minutes if the dome lamp control is left on and the ignition has been turned to the off position. The battery saver will also shut off the trunk lamps in 30 minutes if the trunk is left open. SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEM SecuriLock威 passive anti-theft system is an engine immobilization system.
Locks and Security Anti-theft indicator The anti-theft indicator is located in the instrument cluster. • When the ignition is in the off position, the indicator will flash once every two seconds to indicate the SecuriLock威 system is functioning as a theft deterrent. • When the ignition is in the on position, the indicator will glow for three seconds, then turn off to indicate normal system functionality.
Locks and Security Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys. Programming spare keys You can program your own integrated keyhead transmitters or standard SecuriLock威 coded keys to your vehicle.
Locks and Security 6. Turn the ignition to the 1 (off) position and remove the second previously programmed coded key from the ignition. 7. After three seconds but within 20 seconds of turning the ignition to the 1 (off) position and removing the previously programmed coded key, insert the new unprogrammed key (new key/valet key) into the ignition. 8. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep the ignition in the 3 (on) position for at least six seconds. 9.
Locks and Security The interior motion detection and vehicle incline sensing systems will operate only when the vehicle is locked using the remote keyless entry transmitter or when using the power door lock control with the accompanying door open and all doors then become closed. For convertible vehicles, the convertible top must be in the fully closed and latched position for the interior motion sensing system to arm.
Locks and Security Each door, the hood or the trunk is armed individually, and if any are open, they must be closed for the system to enter the 20 second countdown. The turn signal lamps will flash once when all doors, the hood and the trunk are closed indicating the vehicle is locked and entering the 20 second countdown. If any closure is not properly closed the turn signal lamps will not flash and that closure will not be armed.
Seating and Safety Restraints FRONT SEATS WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
Seating and Safety Restraints The non-adjustable head restraints consist of a trimmed foam covering over the upper structure of the seatback. Properly adjust the seatback to an upright driving/riding position, so that the head restraint is positioned as close as possible to the back of your head. Adjustable head restraints (if equipped) Your vehicle may be equipped with front row outboard head restraints that are vertically adjustable.
Seating and Safety Restraints To adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint. Properly adjust the head restraint so that the top of the head restraint is even with the top of your head and positioned as close as possible to the back of your head.
Seating and Safety Restraints To remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint. To reinstall the adjustable head restraint, do the following: 1. Insert the two stems into the guide sleeve collars. 2. Push the head restraint down until it locks.
Seating and Safety Restraints WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Titling head restraints (if equipped) The front head restraints may have a tilting feature for extra comfort. To tilt the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Pivot the head restraint forward toward your head to the desired position.
Seating and Safety Restraints Pull lever up to adjust the angle of the seatback. Four-way seat adjust (driver side only) Pump the handle upwards to raise the cushion and pump downward to lower the cushion to the desired location. Adjusting the power seats (if equipped) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Seating and Safety Restraints WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.
Seating and Safety Restraints Move the switch in the direction of the arrows to raise or lower the rear portion of the seat cushion. Press the switch in the direction of the arrows to move the seat forward, backward, up or down. Using the power lumbar support (if equipped) The power lumbar control is located on the top of the driver’s seat side shield. Press one side of the control to increase lower back firmness. Press the other side of the control to decrease lower back firmness.
Seating and Safety Restraints Heated seats (if equipped) WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time.
Seating and Safety Restraints Use the recliner handle to return the seatback to the desired position. REAR SEATS (IF EQUIPPED) Non-adjustable head restraints Your vehicle is equipped with second row outboard non-adjustable head restraints. The head restraints can be rotated forward to improve rear vision when there are no rear occupants.
Seating and Safety Restraints Press the button to rotate the head restraint forward in order to improve rear vision when there are no rear seat occupants. 2nd row seat/split-folding rear seat (if equipped) One or both rear seatbacks (coupe only) can be folded down to provide additional cargo space. To lower the seatback(s) from inside the vehicle, be sure the head restraint is in the upright position, pull the strap to release the seatback and then fold the seatback down.
Seating and Safety Restraints Rear seat delete (if equipped) WARNING: In a collision, passengers who are unbelted are significantly more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. This is not a seating position. Persons or child seats cannot be placed in the rear of vehicles with the rear seat delete option.
Seating and Safety Restraints How does the Personal Safety System™ work? The Personal Safety System can adapt the deployment strategy of your vehicle’s safety devices according to crash severity and conditions. A collection of crash sensors provides information to the Restraints Control Module (RCM). During a crash, the RCM may activate the safety belt pretensioners and/or either none, one, or both stages of the dual-stage airbag supplemental restraints based on crash severity and conditions.
Seating and Safety Restraints very close to the airbag. For other occupants, this occurs when the occupant is not properly restrained by safety belts or child safety seats and they move forward during pre-crash braking. The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained. Accident statistics suggest that children are much safer when properly restrained in the rear seating positions than in the front.
Seating and Safety Restraints effectiveness of the safety belts. In frontal collisions, the safety belt pretensioners can be activated alone or, if the collision is of sufficient severity, together with the front airbags. Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’s forward momentum.
Seating and Safety Restraints WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Seating and Safety Restraints Combination lap and shoulder belts The presenter arm (available on the coupe only) is intended to improve access to the safety belt and to allow access to the rear seat. Rotate the presenter arm toward the front of the vehicle until it locks into place. This allows easier access to the front safety belt for the front seat occupant. To access the second row seats, rotate the arm back to its original position against the trim panel. 1.
Seating and Safety Restraints 2. To unfasten, press the release button and remove the tongue from the buckle. WARNING: The center of the rear seat is NOT designed as a seating position and is not equipped with safety belts. The LATCH anchors were not designed to be used with a child seat in the center position and there is no tether anchor available at the center. Attempted use of the center as a seating position will increase the risk of injury or death in the event of a collision.
Seating and Safety Restraints Safety belt locking modes All safety restraints in the vehicle are combination lap and shoulder belts. The driver safety belt has the first locking mode and the front outboard passenger and rear seat safety belts have both types of locking modes described as follows: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and Safety Restraints How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. WARNING: After any vehicle collision, the safety belt system at all passenger seating positions must be checked by an authorized dealer to verify that the “automatic locking retractor” feature for child seats is still functioning properly.
Seating and Safety Restraints Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. WARNING: Do not use extensions to change the fit of the shoulder belt across the torso.
Seating and Safety Restraints Both the driver’s and passenger’s safety belt usages are monitored and either may activate the Belt-Minder威 feature. The warnings are the same for the driver and the front passenger. If the Belt-Minder威 warnings have expired (warnings for approximately five minutes) for one occupant (driver or front passenger), the other occupant can still activate the Belt-Minder威 feature. If...
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... “Crashes are rare events” “I’m not going far” “Belts are uncomfortable” “I was in a hurry” “Safety belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” 140 2012 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus) Consider... 36700 crashes occur every day.
Seating and Safety Restraints Reasons given... “I have an airbag” “I’d rather be thrown clear” Consider... Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”.
Seating and Safety Restraints WARNING: While the design allows you to deactivate your Belt-Minder威, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave the Belt-Minder威 system activated for yourself and others who may use the vehicle. To reduce the risk of injury, do not deactivate/activate the Belt-Minder威 feature while driving the vehicle. 1. Turn the ignition switch to the on position. DO NOT START THE ENGINE. 2.
Seating and Safety Restraints AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag. WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided.
Seating and Safety Restraints WARNING: Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably. • Recline the seat slightly one or two degrees from the upright position. WARNING: Do not put anything on or over the airbag module.
Seating and Safety Restraints Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision. WARNING: Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag.
Seating and Safety Restraints The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic.
Seating and Safety Restraints • a readiness light and tone • and the electrical wiring which connects the components • Side curtain airbag system. Refer to Side curtain airbag system later in this chapter. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system later in this chapter.
Seating and Safety Restraints The front passenger sensing system uses a ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. The indicator lamp is located on the front edge of the map lamps. Note: The indicator lamp will illuminate for a short period of time when the ignition is turned to the on position to confirm it is functional.
Seating and Safety Restraints • If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat. Occupant Pass Airbag Off Indicator Lamp Unlit Lit Empty seat Small child in child safety seat or booster Small child with safety Lit belt buckled or unbuckled Adult Unlit Passenger Airbag Disabled Disabled Disabled Enabled WARNING: Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a rear seating position.
Seating and Safety Restraints Objects Pass Airbag Off Indicator Lamp Unlit Passenger Airbag Small (i.e. three-ring Disabled binder, small purse, bottled water) Medium (i.e.
Seating and Safety Restraints In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat.
Seating and Safety Restraints WARNING: Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident. WARNING: Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback. WARNING: Do not attempt to service, repair, or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. Contact your authorized dealer as soon as possible.
Seating and Safety Restraints Side airbags, in combination with safety belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side airbags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the airbag on the side affected by the collision will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided to occupants in side impact collisions.
Seating and Safety Restraints Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit.
Seating and Safety Restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be purchased separately from the vehicle.
Seating and Safety Restraints Recommendations for Safety Restraints for Children Child size, height, weight, or Recommended age restraint type Infants or Children weighing 40 lb (18 kg) or Use a child safety seat toddlers less (generally age four or younger) (sometimes called an infant carrier, convertible seat, or toddler seat). Small Children who have outgrown or no Use a belt-positioning children longer properly fit in a child safety booster seat.
Seating and Safety Restraints Recommendations for attaching child safety restraints for children Restraint Type Rear facing child seat Forward facing child seat Forward facing child seat Use any attachment method as indicated below by “X” LATCH LATCH Safety Safety Safety (lower (lower belt belt and belt Child anchors anchors and LATCH only Weight and only) top (lower top tether anchors tether anchor and top anchor) tether anchor) Up to 48 lb X X (21 kg) Up to 48 lb X X X (21 kg) Over 48 lb X X (21 kg) W
Seating and Safety Restraints WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. WARNING: Always restrain an unoccupied child seat or booster seat.
Seating and Safety Restraints Follow all the safety restraint and airbag precautions that apply to adult passengers in your vehicle. If the child is the proper height, age, and weight (as specified by your child safety seat or booster manufacturer), fits the restraint and can be restrained properly, then restrain the child in the child safety seat or with the belt-positioning booster.
Seating and Safety Restraints Installing child safety seats with combination lap and shoulder belts Check to make sure the child seat is properly secured before each use. Children 12 and under should be properly restrained in a rear seating position whenever possible. If all children cannot be seated and restrained properly in a rear seating position, properly restrain the largest child in the front seat.
Seating and Safety Restraints 1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted.
Seating and Safety Restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. 6. Allow the belt to retract to remove slack.
Seating and Safety Restraints towards the buckle will additionally help to remove remaining slack from the belt. 9. Attach the tether strap (if the child seat is equipped). Refer to Attaching child safety seats with tether straps later in this chapter. 10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back.
Seating and Safety Restraints Your vehicle may have LATCH lower anchors for child seat installation at the seating positions marked with the child seat symbol. The LATCH anchors (if equipped) are located at the rear section of the rear seat between the cushion and seat back, below the locator symbols on the seat back. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. Follow the instructions on attaching child safety seats with tether straps.
Seating and Safety Restraints Combining safety belt and LATCH lower anchors for attaching child safety seats When used in combination, either the safety belt or the LATCH lower anchors may be attached first, provided a proper installation is achieved. Attach the tether strap afterward, if included with the child seat. Refer to Recommendations for attaching child safety restraints for children in this chapter.
Seating and Safety Restraints Vehicles without rear seats Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. Once the child safety seat has been installed, using either the safety belt, the lower anchors of the LATCH system, or both, you can attach the top tether strap.
Seating and Safety Restraints 2. Locate the correct anchor for the selected seating position. 3. Open the tether anchor cover.
Seating and Safety Restraints 4. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5. Tighten the child safety seat tether strap according to the manufacturer’s instructions. If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases. For convertible: 1. Route the child safety seat tether strap over the top of the head restraint.
Seating and Safety Restraints Note: The attachments for the convertible boot located on the back of the head restraints are not tether anchors. 2. Access tether anchors located behind the seatback under the vinyl tag marked with the child tether anchor symbol.
Seating and Safety Restraints 3. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 4. Tighten the child safety seat tether strap according to the manufacturer’s instructions. If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases.
Seating and Safety Restraints Booster seats position a child so that vehicle lap/shoulder safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably at the edge of the cushion, while minimizing slouching. Booster seats may also make the shoulder belt fit better and more comfortably. Try to keep the belt near the middle of the shoulder and across the center of the chest.
Seating and Safety Restraints Types of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child’s head (as measured at the tops of the ears) above the top of the seat.
Seating and Safety Restraints Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder.
Seating and Safety Restraints The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is generally best to use a booster seat with lap/shoulder belts in the back seat. Move a child to a different seating location if the shoulder belt does not stay positioned on the shoulder during use.
Tires, Wheels and Loading INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic passenger car tires.
Tires, Wheels and Loading Temperature A B C WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Tires, Wheels and Loading • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 km). • Recommended inflation pressure: The cold inflation pressure found on the Safety Compliance Certification Label or Tire Label located on the B-Pillar or the edge of the driver’s door.
Tires, Wheels and Loading WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents.
Tires, Wheels and Loading Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure. 3. Add enough air to reach the recommended air pressure.
Tires, Wheels and Loading Improper or inadequate vehicle maintenance can cause tires to wear abnormally. Inspect all your tires, including the spare, frequently, and replace them if one or more of the following conditions exist: Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning.
Tires, Wheels and Loading U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters “DOT” and indicates that the tire meets all federal standards.
Tires, Wheels and Loading WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi (1.
Tires, Wheels and Loading Safety Practices WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Driving habits have a great deal to do with your tire mileage and safety.
Tires, Wheels and Loading The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear. Tire Rotation Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance chapter) will help your tires wear more evenly, providing better tire performance and longer tire life. • Rear-wheel drive (RWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks.
Tires, Wheels and Loading 7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for the difference in conditions. The ratings range from 81 mph (130 km/h) to 186 mph (299 km/h).
Tires, Wheels and Loading 9. M+S or M/S: Mud and Snow, or AT: All Terrain, or AS: All Season. 10. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others. 11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. Tire Quality Grades do not apply to this type of tire. 1.
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
Tires, Wheels and Loading following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge, see Inflating your tires in this chapter.
Tires, Wheels and Loading To restore the full functionality of the tire pressure monitoring system, have the damaged road wheel/tire repaired and remounted on your vehicle. For additional information, refer to Changing tires with a TPMS in this section. When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended.
Tires, Wheels and Loading Low tire pressure warning light Flashing warning light Possible cause Customer action required Spare tire in use Repair the damaged road wheel/tire and reinstall it on the vehicle to restore system functionality. For a description on how the system functions, refer to When your temporary spare tire is installed in this section.
Tires, Wheels and Loading SNOW TIRES AND CHAINS WARNING: Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford.
Tires, Wheels and Loading SUMMER TIRES Your Ford vehicle may be equipped with summer tires to provide superior performance on wet and dry roads. Summer tires do not have the Mud and Snow (M+S or M/S) tire traction rating on the tire side wall.
Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label). Look for “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for maximum payload.
Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight.
Tires, Wheels and Loading GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR.
Tires, Wheels and Loading • Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury.
Tires, Wheels and Loading GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing vehicle’s braking system is rated for operation at GVWR, not at GCWR.
Tires, Wheels and Loading Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity.
Tires, Wheels and Loading calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 540 = -103 kg. You will need to reduce the load weight by at least 240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, then the load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb. Now you have the load capacity to transport the cement and your friend home. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (9 x 45 kg) = 635 - 198 - 405 = 32 kg.
Tires, Wheels and Loading WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury. Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle.
Tires, Wheels and Loading Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all running lights, brake lights, turn signals and hazard lights are working. Do not splice into the vehicle lamp wiring for trailer lamps. Your vehicle uses an advanced electronic module to control and monitor your vehicle lamps. Splicing into the wiring or attaching wiring to the vehicle bulb. may DISABLE the rear vehicle lamps or cause them not to function properly.
Tires, Wheels and Loading RECREATIONAL TOWING Follow these guidelines if you have a need for recreational (RV) towing. An example of recreational towing would be towing your vehicle behind a motorhome. These guidelines are designed to ensure that your transmission is not damaged. Do not tow your vehicle with any wheels on the ground, as vehicle or transmission damage may occur. It is recommended to tow your vehicle with all four (4) wheels off the ground such as when using a car-hauling trailer.
Driving STARTING Positions of the ignition 1. Off — locks the automatic transmission gearshift lever and allows key removal. Note: In order to switch off the engine while the vehicle is in motion, shift to neutral and use the brakes to bring the vehicle to a safe stop. After the vehicle has stopped, turn the engine off and shift into park. Then, turn the key to the accessory or off position.
Driving WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions.
Driving If starting a vehicle with an automatic transmission: • Make sure the gearshift is in P (Park). • Make sure the parking brake is set. If starting a vehicle with a manual transmission: • Make sure the parking brake is set.
Driving 3. Turn the key to 3 (on) without turning the key to 4 (start). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to 3 (on) without turning the key to 4 (start). If there is difficulty in turning the key, rotate the steering wheel until the key turns freely. 2. Turn the key to 4 (start), then release the key as soon as the engine begins cranking.
Driving Guarding Against Exhaust Fumes WARNING: If you smell exhaust fumes inside your vehicle, have this checked immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. Important Ventilating Information If you stop your vehicle and leave the engine idling for long periods of time, we recommend that you do one of the following: • Open the windows at least 1 inch (2.5 cm).
Driving • Do not use multiple extension cords. Instead, use one extension cord which is long enough to reach from the engine block heater cord to the outlet without stretching. • Make certain that the extension cord is in excellent condition (not patched or spliced). Store your extension cord indoors at temperatures above 32°F (0°C). Outdoor conditions can deteriorate extension cords over a period of time.
Driving BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and should be inspected by an authorized dealer. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by an authorized dealer. Refer to Warning lights and ! P chimes in the Instrument Cluster chapter for information on the brake BRAKE system warning light.
Driving Parking brake To set the parking brake (1), pull the parking brake handle up as far as possible. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. ! P BRAKE To release, press and hold the button (2), pull the handle up slightly, then push the handle down. WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission).
Driving WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and/or wheel/tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the AdvanceTrac威 system. In addition, installing any stereo loudspeakers may interfere with and adversely affect the AdvanceTrac威 system.
Driving The AdvanceTrac威 system includes a stability control button located on the center console, a stability control light and a stability control off light in the instrument cluster. Both the stability control light and the stability control off light in the instrument cluster will illuminate temporarily during start-up as part of a normal system self-check. The stability control light may illuminate (flash) during certain driving situations which cause the AdvanceTrac威 system to operate.
Driving If the TCS is activated excessively in a short period of time, the braking portion of the system may become temporarily disabled to allow the brakes to cool down. In this situation, the TCS will use only engine power reduction or transfer to help control the wheels from over-spinning. When the brakes have cooled down, the system will regain all features. Anti-lock braking, and ESC are not affected by this condition and will continue to function during the cool-down period.
Driving The stability control button can be used to enable unique AdvanceTrac威 modes. Full features of the AdvanceTrac威 system can be restored by pressing the stability control button again or by turning off and restarting the engine. When features of the AdvanceTrac威 system are off, the stability control off light will illuminate steadily. Pressing the stability control button OFF again will turn off the stability control off light.
Driving AdvanceTrac威 Sport Mode (if equipped) The AdvanceTrac威 system provides an available sport mode on some models. This can be selected utilizing the stability off button as shown in the table above. Sport mode is not intended for use on public roadways as this mode provides less AdvanceTrac威 system intervention than when the default ESC and traction control systems are on. Sport mode will allow more spirited driving while the AdvanceTrac威 system is still enabled.
Driving After selecting the desired setting, you may feel a soft feedback bump in the steering wheel when the changeover occurs. Note: If the battery is disconnected or removed, the steering setting will default to standard. Refer to Message center in the Instrument Cluster chapter. AXLE INFORMATION Traction-Lok™ axle (if equipped) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface.
Driving If you cannot move the gearshift lever out of P (Park) with ignition in the on position and the brake pedal pressed: 1. Apply the parking brake. 2. Using a flat head screwdriver or similar tool, remove the cap. 3. Locate the access hole at the front of the area under the cover. 4. Insert the screwdriver or similar tool into the hole and press and hold the lever forward while pulling the gearshift lever out of the P (Park) position and into the N (Neutral) position. 5. Reinstall the cap. 6.
Driving AUTOMATIC TRANSMISSION (IF EQUIPPED) Driving with a 6-speed automatic transmission Your vehicle has been designed to improve fuel economy by reducing fuel usage while coasting or decelerating. When you take your foot off the accelerator pedal and the vehicle begins to slow down the torque converter clutch locks up and aggressively shuts off fuel flow to the engine while decelerating.
Driving N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Drive) standard mode The normal driving position for the best fuel economy. Transmission operates in gears one through six. D (Drive) with grade assist Press the transmission control switch on the side of the shift handle to activate grade assist. • This position allows for gears 1–5 and provides increased engine braking.
Driving • To return to D (Drive) standard mode or 3 (Third), move the transmission shift lever into the D (Drive) or 3 (Third) position. • Selecting 2 (Second) at higher speeds will cause the transmission to downshift to second gear at the appropriate vehicle speed. 1 (First) This position allows for first gear only. • Provides maximum engine braking.
Driving To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the gearshift lever in the neutral position. R 1 3 5 3. Start the engine. 2 4 6 4. Press the brake pedal and move the gearshift lever to the desired gear; 1 (First) or R (Reverse). 5. Release the parking brake, then slowly release the clutch pedal while slowly pressing on the accelerator. During each shift, the clutch pedal must be fully pressed to the floor.
Driving For the 3.7L V6 with 3.31 axle ratio, shift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1-2 13 mph (21 km/h) 2-3 26 mph (42 km/h) 3-4 37 mph (59 km/h) 4-5 43 mph (69 km/h) 5-6 59 mph (95 km/h) For the 5.
Driving 2. Press the clutch pedal to the floor to disengage clutch. 3. Shift into R (Reverse) by pushing the gearshift knob down, then moving the lever fully to the left, then forward. If R (Reverse) is not fully engaged, press the clutch pedal down and return the gearshift to the neutral position. Release the clutch pedal for a moment, then press it down and shift to R (Reverse) again. Parking your vehicle 1. Apply the brake and shift into the neutral position. 2.
Driving WARNING: To help avoid personal injury, always use caution when in R (Reverse) and when using the RSS. WARNING: This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.
Driving Keep the RSS sensors (located on the rear bumper/fascia) free from snow, ice and large accumulations of dirt (do not clean the sensors with sharp objects). If the sensors are covered, it will affect the accuracy of the RSS. If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms.
Driving Image delay if displayed through the navigation screen: After shifting out of R (Reverse) and into any gear other than P (Park), the image in the navigation screen will remain until the vehicle speed reaches 5 mph (8 km/h), only if the rear camera delay feature is on, or until any navigation radio button is pressed. Note: The default setting for the rear camera delay is off. Press the “Settings” button found on the navigation screen to set the rear camera delay feature to on or off.
Driving Servicing • If the image comes on while the vehicle is not in R (Reverse), have the system inspected by your authorized dealer. • If the image is not clear, then check if there is anything covering the lens such as dirt, mud, ice, snow, etc. If the image is still not clear after cleaning, have your system inspected by your authorized dealer. BLIND SPOT MIRRORS (IF EQUIPPED) Blind spot mirrors have a convex spotter mirror built into the upper outboard corner of the outside mirrors.
Driving DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water, traction or brake capability may be limited. Also, water may enter your engine’s air intake and severely damage your engine or your vehicle may stall.
Roadside Emergencies ROADSIDE ASSISTANCE Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24-hours, seven days a week • for the coverage period listed on the Roadside Assistance Card included in your Owner Guide portfolio.
Roadside Emergencies Vehicles sold in the U.S. : Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. This card is found in the Owner’s Guide portfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest dealership within 35 miles (56 km).
Roadside Emergencies FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision due to this feature, you may restart your vehicle by doing the following: 1. Turn the ignition switch to the off position. 2. Turn the ignition switch to the on position.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.
Roadside Emergencies Passenger compartment fuse panel The fuse panel is located in the lower passenger side area behind the kick panel. Open the trim panel door and remove the fuse cover to access the fuses. To remove a fuse, use the fuse puller tool provided to the left of the fuses and relays.
Roadside Emergencies Fuse/Relay Location 6 7 8 9 10 11 12 13 14 Fuse Amp Rating 20A 10A 10A 15A 15A 10A 7.
Roadside Emergencies Fuse/Relay Location 35 Fuse Amp Rating 10A 36 37 38 39 40 41 5A 10A 20A 20A 20A 15A 42 43 44 45 10A 10A 10A 5A 46 7.
Roadside Emergencies WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter. The high-current fuses are coded as follows.
Roadside Emergencies Fuse/Relay Location 9 10 11 12 13 14 15 Fuse Amp Rating 30A* 30A* — — 20A** 25A** — 10A** 16 17 18 19 20 21 22 23 20A** 10A** 20A* 30A* 30A* 30A* 20A* 10A** 24 25 26 10A** 10A** 20A** 27 20A** 28 29 30 31 32 33 34 35 — 30A* — 30A* 30A* 30A* 30A* 40A* 240 2012 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus) Protected Circuits Wipers ABS valve Not used Not used Fuel pump relay (non-Shelby) Fuel pump relay (Shelby only) Not used Intercooler pump relay (Shelby only) Heate
Roadside Emergencies Fuse/Relay Location 36 37 38 39 40 41 42 Fuse Amp Rating Diode — 15A** 5A** 15A** G8VA relay G8VA relay 43 44 45 46 G8VA relay — 5A** 5A** 47 48 49 15A** 15A** 15A** 50 51 52 53 54 55 56 Full ISO relay Full ISO relay Full ISO relay Full ISO relay Full ISO relay Full ISO relay High current relay 57 Full ISO relay 58 High current relay * Cartridge Fuses ** Mini Fuses Protected Circuits Fuel diode Not used Fuel injectors (Shelby only) Rear defroster coil (run/start) PCM vehicle pow
Roadside Emergencies Auxiliary relay with heated seats (if equipped) On heated seat equipped vehicles, there is a relay box located under the driver seat containing two relays for the driver and passenger heated seats. CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road.
Roadside Emergencies A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only” molded in the sidewall 2.
Roadside Emergencies The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehi
Roadside Emergencies WARNING: If the vehicle slips off the jack, you or someone else could be seriously injured. WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Block both the front and rear of the wheel diagonally opposite the flat tire.
Roadside Emergencies 3. Remove the center ornament (if equipped) from the wheel. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 4. Put the jack in the jack notch next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground. Never use the rear differential as a jacking point.
Roadside Emergencies 6. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. If you are using the temporary tire, the lug nut washers will not appear to be flush with the rim. This is normal only when using the temporary spare tire. 7. Lower the wheel by turning the jack handle counterclockwise. 8.
Roadside Emergencies 1. Air compressor (inside) 2. Diverter knob 3. On/Off button 4. Air pressure gauge 5. Sealant bottle/canister 6. Sealant filling clear tube 7. Sealant tube — tire valve connector 8. Yellow cap tool 9. Air compressor hose 10. Air hose — tire valve connector 11. Accessory power plug 12. Casing/housing 2 1 3 4 12 5 6 11 10 9 8 7 General information WARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.
Roadside Emergencies • Drive carefully and avoid abrupt steering maneuvers. • Periodically monitor tire inflation pressure in the affected tire; if the tire is losing pressure, have the vehicle towed. • Read the information in the Tips for use of the temporary mobility kit section to ensure safe operation of the temporary mobility kit and your vehicle.
Roadside Emergencies • When inflating a tire or other objects, use the black air hose only. Do not use the transparent hose which is designed for sealant application only. • Operating the temporary mobility kit could cause an electrical disturbance in radio, CD, and DVD player operation (if equipped). .
Roadside Emergencies 4. Plug the power cable into the 12V power point in the vehicle. 5. Remove the warning sticker found on the canister and place it on the top of the instrument panel or the center of the dash. 6. Start the engine (only if the vehicle is outdoors or in a well-ventilated area). 7. Turn dial (1) counterclockwise to the sealant position. Turn on the kit by pressing the on/off button (2). (2) (1) 8.
Roadside Emergencies Note: When the sealing compound is first added into the tire, the air pressure gauge reading on the compressor unit may indicate a higher value; this is normal and should be no reason for concern. The pressure will drop after about 30 seconds of operation. The tire pressure has to be checked with the compressor in the OFF position to get the correct tire pressure reading. WARNING: Do not stand directly over the temporary mobility kit while inflating the tire.
Roadside Emergencies 3. Turn the dial clockwise to the air position. Turn on the kit by pressing the on/off button. 4. Adjust the tire to the recommended inflation pressure from the tire label located on the driver’s door or door jamb area. Note: The tire pressure has to be checked with the compressor in the OFF position to get the correct tire pressure reading. 5. Turn the compressor off by pressing the on/off button. 6.
Roadside Emergencies Removal of the sealant canister from the temporary mobility kit 1. Unwrap the clear tube from the compressor housing. 2. Press the button located on the temporary mobility kit compressor housing below the canister while pulling up on the sealant canister. Installation of the sealant canister to the temporary mobility kit 1. Align the sealant canister with the temporary mobility kit housing.
Roadside Emergencies 2. Once aligned, seat the sealant canister by lightly pushing down until you hear an audible click. 3. Wrap the clear tube around the compressor housing. Note: If you experience any difficulties with the removal or installation of the sealant canister, consult your Ford Motor Company authorized dealer for assistance. Be sure to check the sealant compound’s “use by” date regularly.
Roadside Emergencies WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km) after any wheel disturbance (rotation, flat tire, wheel removal, etc.). Lug nut socket Wheel lug nut torque* size/Bolt size ft-lb N•m 1⁄2 x 20 100 135 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners.
Roadside Emergencies WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel威 system. This could damage the fuel system and its seal, and may cause fuel to run onto the ground instead of filling the tank, all of which could result in serious personal injury. JUMP STARTING WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage.
Roadside Emergencies – – Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. 1 2. Connect the other end of the 4 positive (+) cable to the positive (+) terminal of the assisting battery. + 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4.
Roadside Emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Roadside Emergencies If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
Customer Assistance GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs.
Customer Assistance In Canada: Mailing address Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer. 2.
Customer Assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.
Customer Assistance THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step procedure outlined earlier in this chapter in the Getting the services you need section, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration.
Customer Assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer Assistance If your vehicle must be serviced while you are traveling or living in Asia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, Central America, the Caribbean, and Israel, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY FORD EXPORT OPERATIONS & GLOBAL INITIATIVES 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A.
Customer Assistance If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: Ford Middle East Customer Relationship Center P.O. Box 21470 Dubai, United Arab Emirates Telephone: +971 4 3326084 Toll-Free Number for the Kingdom of Saudi Arabia: 800 8971409 Local Telephone Number for Kuwait: 24810575 FAX: +971 4 3327299 Email: menacac@ford.com www.me.ford.
Customer Assistance Obtaining a French Owner’s Guide French Owner’s Guides can be obtained from your authorized dealer or by contacting Helm, Incorporated using the contact information listed previously in this section. REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Using high pressure water or wand-type car washes may cause damage to tape stripes if the nozzle is positioned closer than 12 inches (30 cm) from the stripe.
Cleaning WAXING • Wash the vehicle first. • Use a quality wax that does not contain abrasives. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your authorized dealer has touch-up paint to match your vehicle’s color.
Cleaning ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft威 Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean.
Cleaning 5.0L V8 ENGINE PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft威 Bug and Tar Remover (ZC-42). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly.
Cleaning D, or F)] in Canada, available from your authorized dealer. This washer fluid contains special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities. Be sure to replace wiper blades when they appear worn or do not function properly. • Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts.
Cleaning • Do not allow air fresheners and hand sanitizers to spill on interior surfaces. If a spill occurs, wipe off immediately. Damage may not be covered by your warranty. WARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the airbag system. If a staining liquid like coffee/juice has been spilled on the instrument panel or on interior trim surfaces, clean as follows: 1.
Cleaning WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and affect performance of the side airbag in a collision. LEATHER SEATS (IF EQUIPPED) • Remove dust and loose dirt with a vacuum cleaner. • Clean spills and stains as quickly as possible.
Cleaning FORD AND LINCOLN CAR CARE PRODUCTS Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications.
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located on the driver’s side kick panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood and secure it with the prop rod.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.7L V6 engine 1 8 2 7 6 1. Battery 2. Engine oil dipstick 3. Engine oil filler cap 4. Brake fluid reservoir 5. Air filter assembly 6. Engine coolant reservoir 7. Windshield washer fluid reservoir 8.
Maintenance and Specifications 5.0L V8 engine 1 8 2 7 3 6 4 5 1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Engine coolant reservoir 7. Windshield washer fluid reservoir 8.
Maintenance and Specifications Engine shield Some vehicles may be equipped with an aero-shield under the engine. Remove the front fasteners of the shield to gain access for service. This includes oil and filter changes. WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
Maintenance and Specifications CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and the windshield. Refer to Windows and wiper blades in the Cleaning chapter.
Maintenance and Specifications 5. Locate and carefully remove the engine oil level dipstick. • 3.7L V6 engine • 5.0L V8 engine - Locate the engine oil dipstick by reaching between the strut tower brace (if equipped) and the hood hinge area.
Maintenance and Specifications 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the lower hole, add enough oil to raise the level within the lower and upper holes. • Oil levels above the upper hole may cause engine damage. Some oil must be removed from the engine by an authorized dealer. 7. Put the dipstick back in and ensure it is fully seated.
Maintenance and Specifications Use SAE 5W-20 engine oil Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers.
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft威 maintenance-free battery which normally does not require additional water during its life of service. Note: If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.
Maintenance and Specifications WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.
Maintenance and Specifications R TU LE AD RE If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. COLD FILL RANGE • The engine coolant should be at the FULL COLD level, or within the COLD FILL or MIN / MAX range as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty.
Maintenance and Specifications • DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants may harm your engine’s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty. Refer to Maintenance product specifications and capacities in this chapter.
Maintenance and Specifications 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, to within the COLD FILL RANGE or the FULL COLD level on the reservoir. If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full. 6. Replace the cap.
Maintenance and Specifications Severe climates If you drive in extremely cold climates: • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • A coolant concentration of 60% will provide improved freeze point protection. Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Maintenance and Specifications If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase.
Maintenance and Specifications FUEL FILTER Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed. For Shelby fuel filter requirements, see the Shelby GT500 Supplement. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure.
Maintenance and Specifications • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water.
Maintenance and Specifications Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the cargo area). • Keep the fuel pump nozzle in contact with the fuel container while filling. • DO NOT use a device that would hold the fuel pump handle in the fill position.
Maintenance and Specifications At the next opportunity, safely pull off the road, turn off the engine, open the fuel filler door and remove any visible debris from the fuel fill opening. Insert either the fuel fill nozzle or the fuel fill funnel (see Refilling with a portable fuel container for funnel location) provided with the vehicle several times to dislodge any debris and/or allow the inlet to close properly.
Maintenance and Specifications Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage. Octane recommendations (5.0L V8 engine) ⬙Regular⬙ unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some stations offer fuels posted as ⬙Regular⬙ with an octane rating below 87, particularly in high altitude areas.
Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. • Normally, adding 1 gallon (3.8L) of fuel is enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than 1 gallon (3.8L) may be required. • The service engine soon indicator may come on.
Maintenance and Specifications 3. Fill the vehicle with fuel from the portable fuel container. 4. When done, clean the funnel or properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel. Do not use aftermarket funnels; they will not work with the Easy Fuel威 system and can damage it. The included funnel has been specially designed to work safely with your vehicle.
Maintenance and Specifications • Use a known quality gasoline, preferably a national brand. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (in gallons or liters). 3.
Maintenance and Specifications • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between the top gears occurs. Unnecessary shifting of this type could result in reduced fuel economy.
Maintenance and Specifications • Close windows for high speed driving. EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately.
Maintenance and Specifications Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal also lists engine displacement.
Maintenance and Specifications Readiness for Inspection/Maintenance (I/M) testing Some state/provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.
Maintenance and Specifications BRAKE/CLUTCH FLUID Brake and clutch (if equipped) systems are supplied from the same reservoir. The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid.
Maintenance and Specifications Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. It is located on the passenger side of the transmission. 2. Remove the filler plug and inspect the fluid level. 3. Note: For vehicles equipped with a V6 engine, the correct manual transmission fill level is at the lower edge of the filler hole. For vehicles equipped with a V8 engine, the correct manual transmission fill level is 1/2 inch (1.3 cm) below the edge of the filler hole.
Maintenance and Specifications Use only fluid that meets Ford specifications. Refer to Maintenance product specifications and capacities in this chapter. AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter element listed. Refer to Motorcraft威 part numbers in this chapter.
Maintenance and Specifications 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 5. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing. Note: Failure to use the correct air filter element may result in severe engine damage.
Maintenance and Specifications Engine • The engine oil and filter should be changed prior to storage, as used engine oil contain contaminates that may cause engine damage. • Start the engine every 15 days. Run at fast idle until it reaches normal operating temperature. • With your foot on the brake, shift through all the gears while the engine is running. Fuel system • Fill the fuel tank with high-quality fuel until the first automatic shutoff of the fuel pump nozzle.
Maintenance and Specifications • Move vehicles at least 25 feet (8 m) every 15 days to lubricate working parts and prevent corrosion. Removing vehicle from storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up on window surfaces. • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collected during storage (mice/squirrel nests).
Capacity Door latch, hood latch, auxiliary hood latch, striker plates, seat tracks and fuel filler door hinge Engine coolant (3.7L engine) Engine coolant (5.0L engine) Door weatherstrips Multi-Purpose Grease (Lithium grease) Motorcraft威 Specialty Orange Engine Coolant 12.4 quarts (11.7L) 13.0 quarts (12.
2012 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus) Motorcraft威 Full Synthetic Manual Transmission Fluid Ford part name or equivalent •Motorcraft威 SAE 5W-20 Premium Synthetic 6.0 quarts (5.7L) Blend Motor Oil (US) •Motorcraft威 SAE 5W-20 Full Synthetic Motor Oil (US) •Motorcraft威 SAE 5W-20 Super Premium Motor Oil (Canada) 8.0 quarts (7.6L) •Motorcraft威 SAE 5W-20 Synthetic Motor Oil (Canada)6 Motorcraft威 Penetrating — and Lock Lubricant Motorcraft威 SAE 5.0 pints (2.
Fill as required 16.0 gallons (60.6L) Windshield washer fluid Fuel tank — Ford part name or equivalent Motorcraft威 Premium Windshield Washer Concentrate (US) Premium Quality Windshield Washer Fluid (Canada) — ZC-32-A (US) CXC-37-(A, B, D and F) (Canada) / WSB-M8B16-A2/- - Ford part number / Ford Specification Add 4 oz. (118 ml) of Additive Friction Modifier XL-3 or equivalent meeting Ford specification EST-M2C118-A for complete refill of Traction-Lok axles.
Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio 3.7L V6 Engine 227 Minimum 87 octane 1-4-2-5-3-6 Coil on plug 0.049–0.053 inch (1.25-1.35 mm) 10.5:1 5.0L V8 Engine 302 Minimum 87 octane 1-5-4-8-6-3-7-2 Coil on plug 0.049–0.053 inch (1.25–1.35 mm) 11.0:1 For Shelby GT500 octane requirements, see the Shelby GT500 Supplement. Engine drivebelt routing 1. Short drivebelt is on first pulley groove closest to engine. 2.
Maintenance and Specifications 1 2 • 5.0L V8 engine IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure (B-Pillar) by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number. XXXXXXXXXXXXXXXXX The Vehicle Identification Number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake system / Gross Vehicle Weight Rating (GVWR) / Restraint Devices and their location 3. Make, vehicle line, series, body type 4.
Maintenance and Specifications TRANSMISSION CODE DESIGNATIONS You can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents.
Accessories FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for your vehicle through your local Ford or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigorous engineering and safety specifications.
Accessories Interior style •Floor mats •Illuminated gear shift knob* •Sport pedals •Illuminated door sill plates •Flexible visor storage system (tissue dispenser, organizer, CD holder) •Auto dimming rearview mirror with compass and temperature Lifestyle •Ash cup / smoker’s package •Cargo net •Soft cargo organizers •Portable navigation system by Garmin* Peace of mind •Full vehicle covers •GPS tracking and recovery* •Remote start •Wiper de-icer and debris cleaner* •Vehicle security systems •Keyless entry keyp
Accessories • The Federal Communications Commission (FCC) and Canadian Radio Telecommunications Commission (CRTC) regulate the use of mobile communications systems — such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician.
Ford Extended Service Plan FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered the powerful protection of Ford ESP. It is the only extended service plan backed by Ford Motor Company, and provides “peace of mind” protection beyond the New Vehicle Limited Warranty coverage. Up to 500+ Covered Vehicle Components There are four, new-vehicle Extended Service Plans with different levels of coverage. Ask your dealer for details.
Ford Extended Service Plan Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. With Ford ESP, you minimize your risk for unexpected repair bills and rising repair costs. Avoid the rising cost of properly maintaining your vehicle! Ford ESP also offers a Premium Maintenance Plan that covers items that routinely wear out. The coverage is prepaid, so you never have to worry about affording your vehicle maintenance.
Ford Extended Service Plan 325 2012 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)
Ford Extended Service Plan FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a Ford Extended Service Plan (ESP). Ford ESP is the only service contract backed by Ford Motor Company of Canada, Limited.
Scheduled Maintenance GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it. It is your responsibility to see that all scheduled maintenance is performed and that the materials used meet Ford engineering specifications as identified in the Maintenance and Specifications chapter.
Scheduled Maintenance Your vehicle is very sophisticated and built with multiple complex performance systems. Every manufacturer develops these systems using different specifications and performance features. That’s why it’s important to rely upon your dealership to properly diagnose and repair your vehicle. Ford Motor Company has recommended maintenance intervals for various parts and component systems based upon engineering testing.
Scheduled Maintenance Genuine Ford parts and service When planning your maintenance services, consider your dealership for all your vehicle’s needs. There are a lot of reasons why visiting your dealership for all your service needs is a great way to help keep your vehicle running great. Convenience Many dealerships have extended evening and Saturday hours to make your service visit more convenient.
Scheduled Maintenance Any adverse condition should be brought to the attention of your dealer or qualified service technician as soon as possible for the proper service advice. The owner maintenance service checks are generally not covered by warranties so you may be charged for labor, parts or fluids used. Engine oil/coolant change intervals – 3.7L and 5.
Scheduled Maintenance Multi-point inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly. This can help identify potential issues and prevent major problems. Ford Motor Company recommends the following multi-point inspection be performed at every scheduled maintenance interval to help ensure your vehicle keeps running great.
Scheduled Maintenance 332 2012 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)
Scheduled Maintenance NORMAL SCHEDULED MAINTENANCE AND LOG Intelligent Oil Life Monitor™ – 3.7L and 5.0L Engines Your vehicle is equipped with an Intelligent Oil Life Monitor™ that determines when the engine oil should be changed based on how your vehicles is used. By using several important factors in its calculations, the monitor helps reduce the cost of owning your vehicle and reduce environmental waste at the same time.
Scheduled Maintenance Normal Scheduled Maintenance At every oil change Change engine oil and filter interval as indicated by Rotate tires, inspect tire wear and measure the message center tread depth Perform multi-point inspection (recommended) Inspect automatic transmission fluid level (if equipped with dipstick); consult dealer for requirements Inspect brake pads, shoes, rotors, drums, brake linings, hoses and parking brake Inspect cabin air filter (if equipped) Inspect engine cooling system strength and
Additional maintenance items1 Miles (x 1,000) 20 30 40 60 80 90 100 120 140 150 Kilometers (x 1,000) 32 48 64 96 128 144 160 192 225 240 Replace cabin air filter (if equipped) • • • • • • • Replace climate-controlled seat filter (if equipped) • • • • • Replace engine air filter • • • • • 2 Change engine coolant • Replace spark plugs • Inspect accessory drive belt(s) • • Change automatic transmission fluid and filter • Change manual transmission fluid • Replace accessory drive belt(s) if not replaced within
Scheduled Maintenance Maintenance schedule log DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A COD
Scheduled Maintenance DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER
Scheduled Maintenance DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER
Scheduled Maintenance SPECIAL OPERATING CONDITIONS – 3.7L AND 5.0L ENGINES If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the additional maintenance. For specific recommendations, see your dealership service advisor or technician.
Scheduled Maintenance Example #1: The OIL CHANGE REQUIRED message comes on at 28,751 miles (46,270 km); perform the 30,000 mile (48,000 km) automatic transmission fluid replacement. Example #2: The OIL CHANGE REQUIRED message has not come on but the odometer reads 30,000 miles (48,000 km); perform the engine air filter replacement. (i.e., Intelligent Oil Life Monitor™ was reset at 25,000 miles [40,000 km].
Scheduled Maintenance Special operating condition log DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE:
Scheduled Maintenance DEALER VALIDATION: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER VALIDATION: RO#: DATE: P&A CODE: HOURS: MILEAGE: DEALER
Scheduled Maintenance EXCEPTIONS There are several exceptions to the Normal Schedule. They are listed below: Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped with Ford-design axles are lubricated for life; do not check or change fluid unless a leak is suspected, service is required or the assembly has been submerged in water.
Scheduled Maintenance Edge/MKX AWD only – vehicles operating off-road in sand during high ambient temperatures must replace the AWD PTU (All-wheel drive Power Transfer Unit) lube every 20,000 miles (32,000 km). Engine air filter & cabin air filter replacement: Engine air filter and cabin air filter life is dependent on exposure to dusty and dirty conditions. Vehicles operated in these conditions will require frequent inspection and replacement of the engine air filter and cabin air filter.
Index A Accessory delay ..........................78 AdvanceTrac ..............................213 AdvanceTrac Sport Mode .........218 Airbag supplemental restraint system ................................143, 151 and child safety seats ............145 description ......................143, 151 disposal ....................................154 driver airbag ....................145, 152 indicator light .........................154 operation .........................145, 152 passenger airbag .............
Index attaching with tether straps ..165 in front seat ............................160 in rear seat ..............................160 LATCH .....................................163 recommendations ...................157 Child safety seats - booster seats ...........................................171 Cleaning your vehicle engine compartment ..............272 instrument panel ....................274 interior .....................................275 plastic parts ............................273 washing ......
Index cleaning ...................................272 coolant .....................................289 fail-safe cooling .......................293 idle speed control ...................287 lubrication specifications .......313 refill capacities ........................313 service points ..................280–281 Engine block heater .................210 Engine oil ..................................283 checking and adding ..............283 dipstick ....................................
Index Inspection/maintenance (I/M) testing ........................................306 Instrument panel cleaning ...................................274 cluster ........................................12 lighting up panel and interior .......................................59 J Jack ............................................242 positioning ...............................242 storage .....................................242 Jump-starting your vehicle ......257 K Keyless entry system autolock ................
Index Parking brake ............................213 Parts (see Motorcraft威 parts) ...........312 Passenger Occupant Classification Sensor .................130 Power distribution box (see Fuses) ...............................238 Power mirrors .............................79 Powerpoint ..................................75 Power steering ..........................218 Power Windows ...........................75 R Radio ............................................29 6-CD in dash .............................
Index Steering wheel controls ......................................82 tilting .........................................71 Stereo 6-CD in dash .............................29 CD-MP3 .....................................29 SYNC威 ..........................................47 T Temporary mobility kit .............247 Transmission automatic operation ...............221 brake-shift interlock (BSI) ....219 fluid, checking and adding (automatic) .............................
