Datasheet

No. Item Specifications Testing Method
15
Humidity (Under
Steady State)
Appearance
Capacitance
Change
D.F.
I.R.
No marked defect
Char. B: Within ±10%
Char. E: Within ±20%
Char. F: Within ±30%
Char. B, E: 5.0% max.
Char. F: 7.5% max.
1000MΩ min.
Set the capacitor for 500 +24/-0 hrs. at 40±2°C in 90 to 95%
relative humidity.
Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,
then placed at *room condition for 24±2 hrs.
before initial measurements.
Post-treatment: Capacitor should be stored for 1 to 2 hrs. at
*room condition.
16
Humidity
Loading
Appearance
No marked defect
Capacitance
Change
Char. B: Within ±10%
Char. E: Within ±20%
Char. F: Within ±30%
D.F.
Char. B, E: 5.0% max.
Char. F: 7.5% max.
I.R.
500MΩ min.
Apply the rated voltage for 500 +24/-0 hrs. at 40±2°C in 90 to
95% relative humidity. (Charge/Discharge currentV50mA)
Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,
then placed at *room condition for 24±2 hrs.
before initial measurements.
Post-treatment: Capacitor should be stored at 85±2°C for 1 hr.,
then placed at *room condition for 24±2 hrs.
17 Life
Appearance
No marked defect
Capacitance
Change
Char. B: Within ±10%
Char. E: Within ±20%
Char. F: Within ±30%
D.F.
Char. B, E: 4.0% max.
Char. F: 7.5% max.
I.R.
2000MΩ min.
Apply a DC voltage of 150% of the rated voltage for
1000 +48/-0 hrs. at 85±2°C with a relative humidity of 50%
max. (Charge/Discharge currentV50mA)
Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,
then placed at *room condition for 24±2 hrs.
before initial measurements.
Post-treatment: Capacitor should be stored at 85±2°C for 1 hr.,
then placed at *room condition for 24±2 hrs.
14
Temperature
and Immersion
Cycle
Appearance
No marked defect
Capacitance
Change
Char. B: Within ±10%
Char. E: Within ±20%
Char. F: Within ±30%
D.F.
Char. B, E: 4.0% max.
Char. F: 7.5% max.
I.R.
2000MΩ min.
Dielectric Strength
(Between Lead
Wires)
Per item 4.
The capacitor should be subjected to 5 temperature cycles,
then consecutively to 2 immersion cycles.
<Temperature cycle>
Cycle time: 5 cycle
<Immersion cycle>
Cycle time : 2 cycle
Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,
then placed at *room condition for 24±2 hrs.
before initial measurements.
Post-treatment: Capacitor should be stored for 4 to 24 hrs. at
*room condition.
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued from the preceding page.
1
Time (min)
-25±3 30
2 Room Temp. 3
3 85±3 30
4 Room Temp. 3
Step Temperature (°C)
Time (min)
1 65 +5/-0 Clean water15
2 0 ±3 Salt water15
Step Temperature (°C) Immersion water
13
Soldering Effect
(On-Preheat)
Appearance
Capacitance
Change
Dielectric Strength
(Between Lead
Wires)
No marked defect
Char. B: Within ± 5%
Char. E: Within ± 15%
Char. F: Within ± 20%
Per item 4.
First the capacitor should be
stored at 120+0/-5°C for
60+0/-5 sec.
Then, as in figure, the lead wires
should be immersed solder of
260+0/-5°C up to 1.5 to 2.0mm
from the root of terminal for
7.5+0/-1 sec.
Pre-treatment: Capacitor should be stored at 85±2°C for 1 hr.,
then placed at *room condition for 24±2 hrs.
before initial measurements.
Post-treatment: Capacitor should be stored for 4 to 24 hrs. at
*room condition.
,,,,,,,,,,
,,,,,,,,,,
,
,
,
,,,
,,,,
,,,,,,
,
,
,
,
,
,
Thermal
Screen
Capacitor
1.5
to 2.0mm
Molten
Solder
DEB Series Specifications and Test Methods
48
9
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note
C85E.pdf
06.6.1