Data Sheet

ManualsBrandsMurata ManualsElectronicsBluetooth Low Energy Module

MBN52832 Data Sheet, v1.4a, 02/06/2020 Page 29 of 34 www.murata.com

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver.

 Is connected.

 Consult the dealer or an experienced radio/TV technician for help.

11.2 FCC Labeling Requirements

When integrating the MBN52832 into a product the FCC labeling requirements must be met. This includes a clearly visible

label on the outside of the finished product specifying the MBN52832 FCC identifier (FCC ID: HSW2832) as well as the

notice above. The exterior label can use wording such as “Contains Transmitter Module FCC ID: HSW2832” or “Contains

FCC ID: HSW2832” although any similar wording that expresses the same meaning may be used.

11.3 IC Notice (Canada)

The term “IC” before the certification/registration number only signifies that the Industry Canada technical specifications

were met.

Le terme “IC” devant le numéro de certification /d’enregistrement signifie seulement que les spécifications techniques

Industrie Canada ont été respectées.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to

The following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

Cet appareil est conforme avec Industrie Canada RSS standard exempts de licence (s). Son utilisation est soumise à Les

deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2) cet appareil doit accepter Toute

interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.

This device complies with Health Canada’s Safety Code 6 / IC RSS-210. The installer of this device should ensure that RF

radiation is not emitted in excess of the Health Canada’s requirement. Information can be obtained at: http://www.hc-

sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php

Cet appareil est conforme avec Santé Canada Code de sécurité 6 / IC RSS-210. Le programme d'installation de cet appareil

doit s'assurer que les rayonnements RF n'est pas émis au-delà de l'exigence de Santé Canada. Les informations peuvent

être obtenues: http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php

This radio transmitter MBN52832 has been approved by Industry Canada to operate with the antenna types listed below

with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum

gain indicated for that type, are strictly prohibited for use with this device.

Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du

matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-

dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non

inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation

de l'émetteur.

Table 11.3 External Antenna to comply with IC

Part Number

Vendor

Gain (dBi)

Type

Connector

Remarks

S2406PL

Cushcraft

6.0

Patch

U.FL

Necessary for FCC/IC

compliance only.