Datasheet

ManualsBrandsMURATA POWER SOLUTIONS ManualsPSU ComponentsDC/DC converter (print) 12 V 17 A 204 W No. of outputs: 1 x

UWQ-12/17-Q48T-C Series

Wide Input, Isolated DOSA Quarter Brick

DC-DC Converters with Trim and Sense

MDC_UWQ-12-17-Q48T-C.A01 Page 4 of 17

www.murata-ps.com/support

OUTPUT

Conditions/Comments

➀

Minimum Typical/Nominal Maximum Units

Total Output Power 0.0 204 210 W

Voltage

Setting Accuracy, ﬁ xed output At 50% load, not user adjustable 11.64 12 12.36 Vdc

Output Voltage Range User-adjustable -10 +10 % of Vnom.

Overvoltage Protection Via magnetic feedback 15 Vdc

Current

Output Current Range 0.0 17 17 A

Minimum Load No minimum load

Current Limit Inception 97% of Vnom., cold condition 17.5 19.5 21.5 A

Short Circuit

Short Circuit Current

Hiccup technique, autorecovery within 1.25%

of Vout

56A

Short Circuit Duration

(remove short for recovery)

Output shorted to -Vout, no damage.

Continuous operation

Short circuit protection method Hiccup technique-auto recovery

Regulation ➄

Line Regulation Vin=min. to max., Vout=nom., full load ±0.25 % of Vout

Load Regulation Iout=min. to max., Vin=nom. ±0.3 % of Vout

Ripple and Noise ➅

5 Hz- 20 MHz BW, Cout=1µF MLCC paralleled

with 10µF tantalum

100 120 mV pk-pk

Temperature Coefﬁ cient At all outputs 0.02 % of Vout./°C

Maximum Capacitive Loading Low ESR caps 0 5000 F

Remote Sense Compliance Sense connected at load 10 % of Vout

MECHANICAL (Through Hole Models)

Outline Dimensions (open frame) 2.3x1.45x0.46 Inches

58.4x36.8x11.7 mm

Outline Dimensions (with baseplate) 2.3x1.45x0.5 Inches

58.4x36.8x12.7 mm

Weight With baseplate 2.12 Ounces

With baseplate 60.19 Grams

Without baseplate 1.6 Ounces

Without baseplate 45.36 Grams

Through Hole Pin Diameter 0.04 & 0.06 Inches

1.016 & 1.52 mm

Through Hole Pin Material Copper alloy

TH Pin Plating Metal and Thickness Nickel subplate 50 µ-inches

Gold overplate 5 µ-inches

Baseplate Material Aluminum

ENVIRONMENTAL

Operating Ambient Temperature Range See derating curves -40 85 °C

Operating Case Temperature With baseplate, no derating -40 110 °C

Storage Temperature Vin = Zero (no power) -55 125 °C

Thermal Protection/Shutdown Measured in center 115 125 130 °C

Electromagnetic Interference External ﬁ lter is required

Conducted, EN55022/CISPR22 Class B with external ﬁ lter

RoHS rating RoHS-6

FUNCTIONAL SPECIFICATIONS, (CONT.)

Notes

➀ Unless otherwise noted, all speciﬁ cations apply at Vin = nominal, nominal output voltage and full

output load. General conditions are near sea level altitude, no base plate installed and natural

convection airﬂ ow unless otherwise speciﬁ ed. All models are tested and speciﬁ ed with external

parallel 1 F and 10 F multi-layer output capacitors and a 22µf external input capacitor (see

Technical Notes). All capacitors are low-ESR types wired close to the converter. These capacitors

are necessary for our test equipment and may not be needed in the user’s application.

➁ Input (back) ripple current is tested and speciﬁ ed over 5 Hz to 20 MHz bandwidth. Input ﬁ ltering is

Cin = 33 µF/100V, Cbus = 220µF/100V and Lbus = 12 µH.

➂ All models are stable and regulate to speciﬁ cation under no load.

➃ The Remote On/Off Control is referred to -Vin.

➄ Regulation speciﬁ cations describe the output voltage changes as the line voltage or load current

is varied from its nominal or midpoint value to either extreme. The load step is ±25% of full load

current.

➅ Output Ripple and Noise is measured with Cout = 1µF paralleled with 10µF, 20 MHz oscilloscope

bandwidth and full resistive load.