Datasheet

ManualsBrandsMURATA POWER SOLUTIONS ManualsPSU ComponentsDC/DC converter (print) 12 V 17 A 204 W No. of outputs: 1 x

UWQ-12/17-Q48 Series

Wide Input, Isolated DOSA Quarter Brick DC/DC Converters

MDC_UWQ-12/17-Q48 Series.A06 Page 4 of 17

www.murata-ps.com/support

OUTPUT

Conditions

➀

Minimum Typical/Nominal Maximum Units

Total Output Power 0.0 204 210 W

Voltage

Setting Accuracy, ﬁ xed output At 50% load, not user adjustable 11.64 12 12.36 Vdc

Overvoltage Protection Via magnetic feedback 15 Vdc

Current

Output Current Range 0.0 17 17 A

Minimum Load No minimum load

Current Limit Inception 97% of Vnom., cold condition 19 21 23 A

Short Circuit

Short Circuit Current

Hiccup technique, autorecovery within 1.25%

of Vout

56A

Short Circuit Duration

(remove short for recovery)

Output shorted to ground, no damage Continuous

Short circuit protection method Hiccup current limiting Non-latching

Regulation ➄

Line Regulation Vin=min. to max., Vout=nom., full load ±0.65 % of Vout

Load Regulation Iout=min. to max., Vin=nom. ±1.5 % of Vout

Ripple and Noise ➅

5 Hz- 20 MHz BW, Cout=1µF MLCC paralleled

with 10µF tantalum

100 120 mV pk-pk

Temperature Coefﬁ cient At all outputs 0.02 % of Vout./°C

Maximum Capacitive Loading Full resistive load, low ESR 0 5000 F

MECHANICAL (Through Hole Models)

Outline Dimensions (no baseplate) 2.3x1.45x0.46 max. Inches

(Please refer to outline drawing) LxWxH 58.4x36.8x11.68 mm

Outline Dimensions (with baseplate) 2.3x1.45x0.5 Inches

58.4x36.8x12.7 mm

Weight No baseplate 1.6 Ounces

No baseplate 45 Grams

With baseplate 2.24 Ounces

With baseplate 63.5 Grams

Through Hole Pin Diameter 0.04 & 0.06 Inches

1.016 & 1.52 mm

Through Hole Pin Material Copper alloy

TH Pin Plating Metal and Thickness Nickel subplate 50 µ-inches

Gold overplate 5 µ-inches

Baseplate Material Aluminum

ENVIRONMENTAL

Operating Ambient Temperature Range See derating curves -40 85 °C

Operating Case Temperature With baseplate, no derating -40 110 °C

Storage Temperature Vin = Zero (no power) -55 125 °C

Thermal Protection/Shutdown Measured in center 115 125 130 °C

Electromagnetic Interference External ﬁ lter is required

Conducted, EN55022/CISPR22 B Class

Radiated, EN55022/CISPR22 B Class

RoHS rating RoHS-6

FUNCTIONAL SPECIFICATIONS, (CONT.)

Notes

➀ Unless otherwise noted, all speciﬁ cations apply at Vin = nominal, nominal output voltage and full

output load. General conditions are near sea level altitude, no base plate installed and natural

convection airﬂ ow unless otherwise speciﬁ ed. All models are tested and speciﬁ ed with external

parallel 1 F and 10 F multi-layer ceramic output capacitors and a 22µF external input capacitor

(see Technical Notes). All capacitors are low-ESR types wired close to the converter. These capaci-

tors are necessary for our test equipment and may not be needed in the user’s application.

➁ Input (back) ripple current is tested and speciﬁ ed over 5 Hz to 20 MHz bandwidth. Input ﬁ ltering is

Cin = 33 µF/100V, Cbus = 220µF/100V and Lbus = 12 µH.

➂ All models are stable and regulate to speciﬁ cation under no load.

➃ The Remote On/Off Control is referred to -Vin.

➄ Regulation speciﬁ cations describe the output voltage changes as the line voltage or load current

is varied from its nominal or midpoint value to either extreme. The load step is ±25% of full load

current.

➅ Output Ripple and Noise is measured with Cout = 1 µF || 10 µF, 20 MHz oscilloscope bandwidth

and full resistive load.