Datasheet

ManualsBrandsMURATA POWER SOLUTIONS ManualsPSU ComponentsDC/DC converter (print) 12 V 17 A 204 W No. of outputs: 1 x

The UWQ series offers high output current (up to

17 Amps) in an industry standard “quarter brick”

package requiring no heat sink for most applica-

tions. The UWQ series delivers ﬁ xed DC output

voltages up to 204 Watts (12V @17A) for printed

circuit board mounting. Wide range inputs of 18

to 75 Volts DC (48 Volts nominal) are ideal for

datacom and telecom systems.

Advanced automated surface mount assembly

and planar magnetics deliver galvanic isolation

rated at 2250 Vdc for basic insulation. To power

digital systems, the outputs offer fast settling to

current steps and tolerance of higher capacitive

loads. Excellent ripple and noise speciﬁ cations as-

sure compatibility to CPU’s, ASIC’s, programmable

logic and FPGA’s. No minimum load is required.

For systems needing controlled startup/shutdown,

an external remote On/Off control may use either

positive or negative logic.

A wealth of self-protection features include

input undervoltage lockout and overtemperature

shutdown using an on-board temperature sensor;

overcurrent protection using the “hiccup” auto-

restart technique, provides indeﬁ nite short-circuit

protection, along with output OVP. The synchronous

rectiﬁ er topology offers high efﬁ ciency for minimal

heat generation and “no heat sink” operation. The

UWQ series is certiﬁ ed to safety standards UL/

EN/IEC/CSA 60950-1, 2nd edition. It meets RFI/

EMI conducted/radiated emission compliance to

EN55022, CISPR22 with an external ﬁ lter.

PRODUCT OVERVIEW

APPLICATIONS



Embedded systems, datacom and telecom

installations, wireless base stations



Disk farms, data centers and cellular repeater sites



Remote sensor systems, dedicated controllers



Instrumentation systems, R&D platforms, auto-

mated test ﬁ xtures



Data concentrators, voice forwarding and

speech processing systems

FEATURES



Fixed DC outputs, 12V @17A



Industry standard quarter brick 2.3” x 1.45” x

0.46” open frame package



Wide range 18 to 75 Vdc input voltages with

2250 Volt Basic isolation



Remote ON/Off enable control



DOSA-compatible pinouts and form factor



High efﬁ ciency synchronous rectiﬁ er topology



Stable no-load operation



Monotonic startup into pre-bias output condition



Certiﬁ ed to UL/EN 60950-1, CSA-C22.2 No.

60950-1, 2nd edition safety approvals



Extensive self-protection, OVP, input undervolt-

age, current limiting and thermal shutdown

External

Power

Source

Reference and

Error Ampliﬁer

-Vout (4)

+Vout (8)

On/Off

Control

(2)

-Vin (3)

Open = On

+Vin (1)

logic)

Controller

and Power

Barrier

Figure 1. Connection Diagram

Typical topology is shown. Murata Power Solutions recommends an external fuse.

UWQ-12/17-Q48 Series

Wide Input, Isolated DOSA Quarter Brick DC/DC Converters

MDC_UWQ-12/17-Q48 Series.A06 Page 1 of 17

www.murata-ps.com

www.murata-ps.com/support

For full details go to

www.murata-ps.com/rohs

Typical unit

Summary of content (17 pages)

PAGE 1
UWQ-12/17-Q48 Series www.murata-ps.com Wide Input, Isolated DOSA Quarter Brick DC/DC Converters PRODUCT OVERVIEW Typical unit FEATURES  Fixed DC outputs, 12V @17A  Industry standard quarter brick 2.3” x 1.45” x 0.46” open frame package  Wide range 18 to 75 Vdc input voltages with 2250 Volt Basic isolation  Remote ON/Off enable control The UWQ series offers high output current (up to 17 Amps) in an industry standard “quarter brick” package requiring no heat sink for most applications.
PAGE 2
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE ➀ Output Root Model ➀ UWQ-12/17-Q48 ➂ Input R/N (mV IOUT IIN full pk-pk) Regulation (Max.) ➁ VOUT (Amps, Power VIN Nom. Range IIN no load (Volts) max.) (Watts) Typ. Max. Line Load (Volts) (Volts) load (mA) (Amps) 12 17 204 100 120 ±1% ±1.5% 48 18-75 ➀ Please refer to the part number structure for additional ordering information and options.
PAGE 3
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters FUNCTIONAL SPECIFICATIONS Conditions ➀ ABSOLUTE MAXIMUM RATINGS Input Voltage, Continuous Full power operation Operating or non-operating, 100 mS max.
PAGE 4
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters FUNCTIONAL SPECIFICATIONS, (CONT.
PAGE 5
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters PERFORMANCE DATA, UWQ-12/17-Q48NB-C 94 92 90 88 86 84 82 80 78 76 74 72 70 68 66 64 62 60 Maximum Current Temperature Derating at sea level (Vin = 24V, air ﬂow from Pin 1 to Pin 4 on PCB, with baseplate) 18 17 16 VIN = 18V VIN = 24V VIN = 36V VIN = 48V VIN = 60V VIN = 75V Output Current (Amps) Efﬁciency (%) Efﬁciency vs. Line Voltage and Load Current @ +25°C 15 14 0.33 m/s (65 LFM) 0.5 m/s (100 LFM) 1.0 m/s (200 LFM) 1.
PAGE 6
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters PERFORMANCE DATA, UWQ-12/17-Q48NB-C Maximum Current Temperature Derating at sea level Vin = 36V (air ﬂow from Pin 1 to Pin 4 on PCB), no baseplate 18 18 17 17 16 16 15 15 Output Current (Amps) Output Current (Amps) Maximum Current Temperature Derating at sea level Vin = 24V (air ﬂow from Pin 1 to Pin 4 on PCB), no baseplate 14 13 0.33 m/s (65 LFM) 0.5 m/s (100 LFM) 1.0 m/s (200 LFM) 1.5 m/s (300 LFM) 2.
PAGE 7
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters PERFORMANCE DATA, UWQ-12/17-Q48NB-C Start-up Delay (Vin=48V, Iout=0A, Cload=0, Ta=+25°C) Ch1= Vin, Ch2= Vout Start-up Delay (Vin=48V, Iout=17A, Cload=0, Ta=+25°C) Ch1= Vin, Ch2= Vout Start-up Delay (Vin=48V, Iout=17A, Cload=5000μF, Ta=+25°C) Ch1= Vin, Ch2= Vout On/Off Enable Delay (Vin=48V, Vout=nom, Iout=0A, Ta=+25°C) Ch1= Enable, Ch2= Vout. On/Off Enable Delay (Vin=48V, Vout=nom, Iout=17A, Ta=+25°C) Ch1= Enable, Ch2= Vout.
PAGE 8
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters PERFORMANCE DATA, UWQ-12/17-Q48NB-C Output ripple and Noise (Vin=48V, Iout=0A, Cload= 1μF || 10μF, Ta=+25°C, BW=20Mhz) Output ripple and Noise (Vin=48V, Iout=17A, Cload= 1μF || 10μF, Ta=+25°C, BW=20Mhz) Thermal image with hot spot at 9.56A with 25°C ambient temperature. Natural convention is used with no forced airﬂow. Identiﬁable and recommended maximum value to be veriﬁed in application.
PAGE 9
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters MECHANICAL SPECIFICATIONS (OPEN FRAME) TOP VIEW END VIEW END VIEW 58.4 2.30 4.78 0.188* [11.68] 0.46 36.8 1.45 1° MAX (ALL PINS) 0.26 0.010 MIN BOTTOM CLEARANCE Mtg Plane SIDE VIEW *Alternate pin lengths available (Contact Murata Power Solutions for information). Pin location dimensions apply at circuit board level. .062 SHOULDER (AT 40 MIL PINS) MATERIAL: .040 PINS: COPPER ALLOY .060 PINS: COPPER ALLOY .
PAGE 10
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters MECHANICAL SPECIFICATIONS (BASEPLATE) 4x M3x0.5 THREADED HOLE (.10 MAX SCREW PENETRATION) TOP VIEW 58.4 2.30 END VIEW END VIEW 12.7 0.50 47.24 1.860 4.78 0.188* 36.8 1.45 1° MAX (ALL PINS) 26.16 1.030 0.26 0.010 MIN BOTTOM CLEARANCE Mtg Plane SIDE VIEW OPTIONAL BASEPLATE 'B' OPTION *Alternate pin lengths available (Contact Murata Power Solutions for information). Pin location dimensions apply at circuit board level. .
PAGE 11
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters RECOMMENDED FOOTPRINT Recommended Footprint (view through converter) REF: DOSA Standard Speciﬁcation for Quarter-Brick DC/DC Converters FINISHED HOLE SIZES @ PINS 1-3 TOP VIEW (PER IPC-D-275, LEVEL C) 0.048-0.062 CL (PRI) (SEC) 1 37.3 1.47 CL 8 7.62 0.300 2 7.62 0.300 4 3 CL FINISHED HOLE SIZES @ PINS 4 & 8 0.100 MIN @ 1-4, 8 FOR PIN SHOULDERS (PER IPC-D-275, LEVEL C) 25.4 1.00 0.070-0.084 50.80 2.000 58.9 2.
PAGE 12
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters STANDARD PACKAGING 9.92 (251.97) REF 9.92 (251.97) REF Each static dissipative polyethylene foam tray accommodates 15 converters in a 3 x 5 array. 0.88 (22.35) REF 2.75 (69.85) ±.25 closed height 11.00 (279.4) ±.25 10.50 (266.7) ±.25 Carton accommodates two (2) trays yielding 30 converters per carton Dimensions are in inches (mm) shown for ref. only. Third Angle Projection Tolerances (unless otherwise speciﬁed): .XX ± 0.
PAGE 13
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters TECHNICAL NOTES Input Fusing Certain applications and/or safety agencies may require fuses at the inputs of power conversion components. Fuses should also be used when there is the possibility of sustained input voltage reversal which is not current-limited. For greatest safety, we recommend a fast blow fuse installed in the ungrounded input supply line. The installer must observe all relevant safety standards and regulations.
PAGE 14
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters CAUTION: If you exceed these Derating guidelines, the converter may have an unplanned Over Temperature shut down. Also, these graphs are all collected near Sea Level altitude. Be sure to reduce the derating for higher altitude. +VOUT C1 C2 SCOPE RLOAD −VOUT C1 = 1μF C2 = 10μF LOAD 2-3 INCHES (51-76mm) FROM MODULE Figure 3.
PAGE 15
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters Remote On/Off Control On the input side, a remote On/Off Control can be speciﬁed with either positive or negative logic as follows: Positive: Models equipped with positive logic are enabled when the On/Off pin is left open or is pulled high to +13.5VDC with respect to –VIN. An internal bias current causes the open pin to rise to +VIN.
PAGE 16
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters Emissions Performance Murata Power Solutions measures its products for radio frequency emissions against the EN 55022 and CISPR 22 standards. Passive resistance loads are employed and the output is set to the maximum voltage. If you set up your own emissions testing, make sure the output load is rated at continuous power while doing the tests.
PAGE 17
UWQ-12/17-Q48 Series Wide Input, Isolated DOSA Quarter Brick DC/DC Converters Vertical Wind Tunnel IR Transparent optical window Variable speed fan Unit under test (UUT) Murata Power Solutions employs a computer controlled custom-designed closed loop vertical wind tunnel, infrared video camera system, and test instrumentation for accurate airﬂow and heat dissipation analysis of power products.