Datasheet

www.murata-ps.com/support
PART NUMBER STRUCTURE
➀ Special quantity order is required; samples available with standard pin length only.
➁ SMT (M) versions not available in sample quantities.
➂ Some model number combinations may not be available. See website or contact your local Murata sales representative.
UEE 150W Series
Isolated, High-Density, Eighth-Brick
DOSA Low Profi le DC-DC Converters
MDC_UEE 150W_Series.A02 Page 2 of 35
Maximum Rated Output
Current in Amps
Eighth-Brick Package
Output Confi guration:
U = Unipolar/Single
Nominal Output Voltage
U EE -
/
D48-3.3
45
Input Voltage Range:
D48 = 36-75V,
48V nominal
PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE
Model Family
Output Input
Effi ciency Dimensions
VOUT
(V)
IOUT
(A)
Power
(W)
Ripple & Noise
(mVp-p) Regulation (max.)
VIN Nom.
(V)
Range
(V)
IIN, no
load
(mA)
IIN, full
load
(A)Typ. Max. Line Load Min. Typ. Inches Millimeters
UEE-3.3/45-D48 3.3 45.5 150 45 80 ±0.1% ±0.25% 48 36-75 80 3.4 91% 92% 2.3 x 0.9 x 0.42 58.42 x 22.9 x 10.7
UEE-5/30-D48 5 30 150 50 80 ±0.1% ±0.1% 48 36-75 100 3.4 91% 92% 2.3 x 0.9 x 0.42 58.42 x 22.9 x 10.7
UEE-12/12.5-D48 12 12.5 150 100 150 ±0.1% ±0.25% 48 36-75 120 3.36 92% 93% 2.3 x 0.9 x 0.42 58.42 x 22.9 x 10.7
➀ Please refer to the model number structure for additional ordering part numbers and options.
➁ All specifi cations are typical unless noted. General conditions for Specifi cations are +25 deg.C,
Vin=nominal, Vout=nominal (no trim installed), full rated load. Adequate airfl ow must be supplied
for extended testing under power.
All models are tested and specifi ed with external 1µF and 10 µF paralleled output capacitors and
no external input capacitor. All capacitors are low ESR types. Caps are layout dependent. These
capacitors are necessary to accommodate our test equipment and may not be required in your
applications. All models are stable and regulate within spec under no-load conditions.
H
Conformal coating (optional)
Blank = no coating, standard
H = Coating added, optional, special quantity order
(not available on SMT models)
C
-
RoHS Hazardous Materials compliance
C = RoHS6 (does not claim EU RoHS exemption 7b–lead in solder), standard
N
On/Off Control Logic
N = Negative logic, standard
P = Positive logic, optional
B
Baseplate (optional, not available on SMT models)
Blank = No baseplate, standard
B = Baseplate installed, optional, special quantity order
Lx
Pin Length Option (Through-hole packages only)
Blank = Standard pin length 0.180 inches (4.6mm)
L1 = Pin length 0.110 inches (2.79mm)
➀
L2 = Pin length 0.145 inches (3.68mm) ➀
M
Surface Mount (SMT models cannot accept the baseplate)
Blank = Thru-hole pin mount, no SMT
M = Surface mount (MSL Rating 2a)
➁