Datasheet

ManualsBrandsMURATA POWER SOLUTIONS ManualsPSU ComponentsDC/DC converter (print) 12 V 30 A 360 W No. of outputs: 1 x

HPH Series

Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters

MDC_HPH_B01 Page 1 of 13

www.murata-ps.com

www.murata-ps.com/support

For full details go to

www.murata-ps.com/rohs

Murata Power Solutions’ fully isolated HPH series of DC/DC converters affords users a practical solu-

tion for their low-voltage/high-current applications. With an input voltage range of 36 to 75 Volts, the HPH

Series delivers up to 70 Amps of output current from a fully regulated 3.3V output.

Using both surface-mount technology and pla-

nar magnetics, these converters are manufactured

on a 2.3" x 2.4", lead-free, open-frame package

with an industry-standard pinout.

HPH converters utilize a full-bridge, ﬁ xed-

frequency topology along with synchronous output

rectiﬁ cation to achieve a high efﬁ ciency. This

efﬁ ciency, coupled with the open-frame package

that allows unrestricted air ﬂ ow, reduces internal

component temperatures thereby allowing operation

at elevated ambient temperatures.

These DC/DC’s provide output trim, sense pins

and primary side on/off control (available with posi-

tive or negative logic). Standard features also include

input undervoltage shutdown circuitry, output

overvoltage protection, output short-circuit and

current limiting protection and thermal shutdown.

All devices are certiﬁ ed to IEC/UL/EN60950-1, 2nd

Edition safety standards and carry the CE mark

(meet LVD requirements).

PRODUCT OVERVIEW

Typical unit

SWITCH

CONTROL

PWM

CONTROLLER

OPTO

ISOLATION

REFERENCE &

ERROR AMP

PULSE

TRANSFORMER

+Vin

(4)

–Vin

(1)

REMOTE

ON /OFF

CONTROL*

(3)

Vout

TRIM

(7)

–SENSE

(8)

–Vout

(9)

+Vout

(5)

+SENSE

(6)

Input undervoltage, input

overvoltage, and output

overvoltage comparators

* Can be ordered with positive (standard) or negative (optional) polarity.

Typical topology is shown. Some models may vary slightly.

FEATURES



RoHS Compliant



3.3V to 12V outputs @ up to 70 Amps



Input range: 36V-75V



Open Frame: 2.3" x 2.4" x 0.40"



Industry-standard package/pinout



Remote sense, Trim, On/Off control



High efﬁ ciency: up to 91%



Fully isolated, 2250Vdc (BASIC)



Input undervoltage shutdown



Output overvoltage protection



Short circuit protection, thermal shutdown



Certiﬁ ed to UL/EN/IEC 60950-1, 2nd Edition,

CAN/CSA-C22.2 No. 60950-1 safety approvals



CE mark



Optional baseplate offers increased thermal

performance

Figure 1. Simpliﬁ ed Schematic

OBSOLETE PRODUCT

Last time buy: August 31, 2014.

Click Here For Obsolescence Notice of February 2014.

Summary of content (13 pages)

PAGE 1
HPH Series www.murata-ps.com Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters Murata Power Solutions’ fully isolated HPH series of DC/DC converters affords users a practical solution for their low-voltage/high-current applications. With an input voltage range of 36 to 75 Volts, the HPH Series delivers up to 70 Amps of output current from a fully regulated 3.3V output. OBSOLETE PRODUCT Last time buy: August PRODUCT 31, 2014.
PAGE 2
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE Output Input Efﬁciency Root Model  VOUT (Volts) IOUT (Amps, Max.) (Watts) Typ. Max. HPH-3.3/70-D48N-C 3.3 70  231 100 125 HPH-5/40-D48N-C 5 40 200 100 125 HPH-12/30-D48N-C 12 30 360 Power R/N (mV pk-pk) Package VIN Nom. (Volts) Range (Volts) IIN, no load (mA) IIN, full load (Amps) Min. Typ. ±0.25% ±0.25% 48 36-75 70 5.35 88% 90% C61 P17 ±0.
PAGE 3
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters FUNCTIONAL SPECIFICATIONS INPUT CHARACTERISTICS Model Family HPH-3.3/70-D48 Start-up UnInput Current 1 threshold dervolt- Reﬂected age (back) Ripple Inrush Output No Low Current ShutTyp. Tran- Short Load Line down12 sient Circuit V V mA pk-pk A2sec mA mA A 35 33.5 20 0.1 50 70 Remote On/Off Control 6 Internal Reverse Polarity Current Standby Input 16 Mode Filter Type Protection (Max.) mA 7.13 1 Pi-type HPH-5/40-D48 35 33.
PAGE 4
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters DYNAMIC CHARACTERISTICS Dynamic Load Response, μSec to ±1% ﬁnal value, (50-75-50%, load step) Start-up Time, VIN to VOUT Remote On/Off to VOUT regulated (Max.) Switching Frequency HPH-3.3/70-D48 HPH-5/40-D48 HPH-3.3/70-D48, HPH-5/40-D48 HPH-3.3/70-D48, HPH-5/40-D48 HPH-3.
PAGE 5
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters TYPICAL PERFORMANCE DATA Transient Response – Model HPH-3.3/70-D48 Transient Response (25% Load Step) Transient Response (50% Load Step) Enable Start-up – Model HPH-3.3/70-D48 Enable Start-up (VIN=48V IOUT=0A) Enable Start-up (VIN=48V IOUT=70A) Ripple and Noise (1uF Ceramic plus 10uF Tantalum) – Model HPH-3.3/70-D48 Ripple Waveform (VIN=48V IOUT=0A) Ripple Waveform (VIN=48V IOUT=70A) www.murata-ps.
PAGE 6
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters TYPICAL PERFORMANCE DATA HPH-3.3/70-D48 Efﬁciency and Power Dissipation Vs. Load Current @ +25ºC HPH-3.
PAGE 7
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters TYPICAL PERFORMANCE DATA 48 95 40 90 32 VIN = 75V VIN = 48V VIN = 36V 85 24 80 16 75 8 Power Dissipation @ Vin = 48V 35 30 Output Current (Amps) 100 HPH-12/30-D48 Maximum Current Temperature Derating at Sea Level (Vin = 48V, Airﬂow is from input to output, baseplate is installed) Loss (Watts) Efﬁciency (%) HPH-12/30-D48 Efﬁciency and Power Dissipation Vs.
PAGE 8
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters MECHANICAL SPECIFICATIONS 2.30 (58.4) A User’s thermal surface and hardware Recommended threaded insert torque is 0.35-0.55 N-M or 3-5 in-lbs. 0.40 (10.2) Do not remove M3 x 0.50 threaded inserts from bottom PCB Baseplate 0.50 (12.7) 0.015 min. clearance between standoffs and highest component 0.18 (4.57) Pin Diameters: Pins 1-4, 6-8 Pins 5, 9 1.900 (48.26) A 0.040 ± 0.001 (1.016 ±0.025) 0.080 ± 0.001 (2.032 ±0.025) 0.
PAGE 9
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters TECHNICAL NOTES Input Fusing Certain applications and/or safety agencies may require fuses at the inputs of power conversion components. Fuses should also be used when there is the possibility of sustained input voltage reversal which is not current-limited. For greatest safety, we recommend a fast blow fuse installed in the ungrounded input supply line. The installer must observe all relevant safety standards and regulations.
PAGE 10
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters +SENSE +OUTPUT 6 COPPER STRIP 5 C1 -OUTPUT -SENSE Note that the temperatures are of the ambient airﬂow, not the converter itself which is obviously running at higher temperature than the outside air. Also note that very low ﬂow rates (below about 25 LFM) are similar to “natural convection”, that is, not using fan-forced airﬂow. C2 SCOPE RLOAD 9 8 COPPER STRIP C1 = 0.
PAGE 11
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters the PWM will restart, causing the output voltage to begin ramping up to its appropriate value. If the short-circuit condition persists, another shutdown cycle will initiate. This on/off cycling is called “hiccup mode”. The hiccup cycling reduces the average output current, thereby preventing excessive internal temperatures. A short circuit can be tolerated indeﬁnitely.
PAGE 12
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters Negative: Optional negative-polarity devices are on (enabled) when the On/Off is grounded or brought to within a low voltage (see Speciﬁcations) with respect to –Vin. The device is off (disabled) when the On/Off is pulled high to +Vin with respect to –Vin. +VOUT +VIN +SENSE ON/OFF CONTROL TRIM LOAD R TRIM DOWN +VIN +VCC –SENSE –VIN ON/OFF CONTROL –VOUT Figure 7.
PAGE 13
HPH Series Isolated, Low VOUT to 70A, Half-Brick DC/DC Converters Vertical Wind Tunnel IR Transparent optical window Murata Power Solutions employs a custom-designed enclosed vertical wind tunnel, infrared video camera system and test instrumentation for accurate airﬂow and heat dissipation analysis of power products. The system includes a precision low ﬂow-rate anemometer, variable speed fan, power supply input and load controls, temperature gauges and adjustable heating element.