User Manual

S5： Print a self-test page to check if the IP address is set correctly.
Note: The serial port needs to set the correct baud rate.
Figure 2
5 Print margins
GS L
[Name] Set the left margin
[Format] ASCII code GS L nL nH
Hexadecimal code 1D 4C nL nH
Decimal code 29 76 nL nH
[Range] 0 ≤ nL ≤ 255
0 ≤ nH ≤ 255
[Description] • Set the left margin with nL and nH；
• The left margin is set to [( nL + nH × 256) × Horizontal moving unit]].
①Test case:
1B 40
1D 4C 00 00
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 4141 41 41 41 41 41 41 41 41 41 41 41
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41
41 41 41 0a
1D 4C 20 00
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 4141 41 41 41 41 41 41 41 41 41 41 41
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41
41 41 41 0a
②Print result description:
The left margin of the first three lines is 0 ( the left and right fixed margins are not counted),
and the left margin of the last three lines is 4 mm.
③Instruction setting calculation instructions:
Set the left margin 4mm= ( nL + nH × 256)* 0. 125mm
nL=32, nH= 0,
Convert to hexadecimal data nL=20, nH= 00
GS W
[Name] Set the print area width
[Format] ASCII code GS W nL nH
Hexadecimal code 1D 57 nL nH
Decimal code 29 87 nL nH
[Range] 0 ≤ nL ≤ 255
0 ≤ nH ≤ 255
[Description] Set the printa rea width with nL and nH.
Set the print area width to [ (nL+nH ×256)×Horizontal moving unit]] .
①Test case:
1B 40
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 0a
1D 57 D0 01
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41
41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 41 0a
②Print result description:
The A print width of the first two lines is the default of 72 mm, and the A print width
of the last two lines is 58 mm.
③Instruction setting calculation instructions:
Set the print width 58mm= ( nL + nH × 256)* 0.125mm
nL=208, nH= 1,
Convert to hexadecimal data nL=D0, nH= 01
 Non-single network port model setting method
S1 Open the V3.1C tool
S2 The communication port selects the remaining interfaces,which can be USB/serial/parallel
S3 Modify the IP address at the“New IP”and click Set New IP (see Figure 2).
S4 The buzzer sounds and the printer restarts to indicate that the setting is successful