User Manual

Magnification table
H o r iz ont a l
m a g n ifica t ion
Ve rt ic a l
m a g n ifica t ion
1 2 3 4 5 6 7 8
H e x D EC He x D EC H e x D EC H ex DEC H ex D EC H ex D EC H e x D EC H e x D EC
1 0 0 0 1 0 1 6 2 0 3 2 3 0 4 8 4 0 6 4 5 0 8 0 6 0 9 6 7 0 1 1 2
2 0 1 1 1 1 1 7 2 1 3 3 3 1 4 9 4 1 6 5 5 1 8 1 6 1 9 7 7 1 1 1 3
3 0 2 2 1 2 1 8 2 2 3 4 3 2 5 0 4 2 6 6 5 2 8 2 6 2 9 8 7 2 1 1 4
4 0 3 3 1 3 1 9 2 3 3 5 3 3 5 1 4 3 6 7 5 3 8 3 6 3 9 9 7 3 1 1 5
5 0 4 4 1 4 2 0 2 4 3 6 3 4 5 2 4 4 6 8 5 4 8 4 6 4 1 0 0 7 4 1 1 6
6 0 5 5 1 5 2 1 2 5 3 7 3 5 5 3 4 5 6 9 5 5 8 5 6 5 1 0 1 7 5 1 1 7
7 0 6 6 1 6 2 2 2 6 3 8 3 6 5 4 4 6 7 0 5 6 8 6 6 6 1 0 2 7 6 1 1 8
8 0 7 7 1 7 2 3 2 7 3 9 3 7 5 5 4 7 7 1 5 7 8 7 6 7 1 0 3 7 7 1 1 9
①Test case:
1B 40
1D 21 11
B1 B6 B8 DF B1 B6 BF ED B5 C4 41 0A
1D 21 33
34 B1 B6 B8 DF BF ED 0A
②Print result description:
The “double height-width A” of the first line is the result of twice the horizontal and vertical
magnification; the “four times the height and width” of the second line is the result of quadrupling
both horizontal and vertical;(Chinese characters and alphanumeric characters can be amplification)
③Instruction setting calculation instructions:
According to the need to horizontally zoom in multiples to look up the table,such as 2 times the
width and height to choose 1D 21 11
2 Density setting
1F 1B 1F 13 14 n
[Name] Set the density level
Decimal code 31 27 31 19 20 n
[Description] Set the density level
[Range] 1<=n< = 8
[Format] Hexadecimal code 1F 1B 1F 13 14 n
3 Sound and light alarm on/off
 Cutter with alarm on/off：1F 1B 1F E0 13 14 m 04 02 03
m=1： Cutter with alarm :on
[Comment] Data filtering beyond the parameter range, the higher the concentration level,
the higher the concentration.
[Default] n=5
1F 1B 1F 13 14 07 set density level 7
m=0： Cutter with alarm :off
 Cutter idle alarm on/off：1F 1B 1F A0 mode 00 0A 00 FF
Test case:
mode=1：Cutter idle alarm on
mode=0：Cutter idle alarm off
4 IP address setting method
 Single network port model setting method：
S1： Open the V3.1C tool
S2： Communication port selection network port
S3: Click“Auto Set Ip” ->click“Search”-> select the IP address of the printer you want to set ->
Modify IP address and gateway parameters -> click“Save”(see Figure 1)
S4： The buzzer sounds and the printer restarts to indicate that the setting is successful.
S5： Print a self-test page to check if the IP address is set correctly.
Figure 1