Contents Chapter Product intro Chapter 1 Product intro intro Minot __ STEPDADS is a new generation of rugged handheld 12 Precaution before using battery __ 13 Notes Chapter 2 Installation instructions 21 Appearance 22 Install Micro SD and SIM cards 23 Battery charge Chapter 3 Keyboard emulator 3] Function setup and key code microprocessor 33 Additional information 34 Continuous scan setup _ enable scanner Chapter 4 Bar code reader-writer Bluetooth 620PS 63 Volume setup 64 Sensor 65 Keyboard 66 Network analo
» Observe and record the information of a new unused and non fully charged battery. On the basis of operating time of new battery ard compare with a battery that has been used for long time. According to product configuration and application program, the operating time of battery would be different. Check battery charging status at regular intervals. When battery operating time drops below about 80%, charging time will be increased remarkably.
2.2 Install Micro SD and SIM cards The cards sockets are showing as follows: 23 Battery charge By using USB Type-C contact, the original adapter should be used for charging the device. Make sure not to use other adapters to charge the device. Chapter 3 Keyboard emulator Keyboard emulator detailed operation manual download link: https/munbynbiz/083kem 3.1 Function setup and key code In the function list, user can select supported function that can be realized by keyboard emulator.
1044645700058 yy. Sa Rasta or Lee hoard 1 BrgadoasiBacelver Keybinding input Enter ae Gatorade data ac GB23I2 Type 1a s » BEEN oni data on the place that user needs. Process mode means haw the data will be processed after bar code data has been read out. Scan content on cursor : enter read-out data in cursor position.
After select “Broadcast Receiver”, “Broadcast name" and "Key" need to be adjusted, Broadcast name: it is the broadcast name of acquired fame shim bar data in cornerstone software. Key: acquire the corresponding key designation of the broadcast. 3.3 Additional information The additional information means acd extra data at front or rear on scanned bar code data. “Prefix: add data at the front of read-out data. “Suffix: add data at the rear of read-out data.
3.4 Continuous scan setup Select continuous scan, user can adjust the interval and time out. again wa Gio ISIS Bauer aad iil ei a ibis tide ied 0 3.5 Enable scanner After all previous functions have been adjusted, click “Enable scanner” to switch on scanner, now user can use all the functions of keyboard emulator. Chapter & Bar code reader-visitor £3 In App Center, to open 2D bar code scan test. €3 Press "SCAN" button or click scan key to start scanning, the parameter "Auto interval” can be adjusted.
Caution: Please scan codes in the comet way ‘otherwise the scanning will be failed. 2D code: 8 f ERE Comet Chapter 5 REID reader SINFUL Click App Center, open *NFC” to read and write tag information.
Chapter 6 Other functions 6.1 Bluetooth £3 Open “BT Printer” in App Center. £ In the list of detected devices, click the device that. you want to pair. £3 Select printer and click “Print” to start printing Lusitania Asian contents. i HEE 63 Volume setup 3 Click “Volume” in App Enter. £3 Setup volume by requirements. GPS £3 Click "GPS" in App Center to open GPS test. £3 Setup GPS parameters to access GPS information.
6.4 Sensor £3 Click “Sensor” in App Center. £3 Setup the sensor by requirements. Sensor vale! 1.8 Light Sensor value? $0 6.5 Keyboard £} Click “Keyboard” in App Center. £3 Setup and test the main value of the device. _166.6 Network i} Click “Network” in App Center. £3 Test WIFI signal by requirements. ante 6.7 Analog call 4 Click "Analog call” in App Center. 3 Test by requirements.
