Munbyn, More choice for your growing business IMC01 Banknote Counter User Manual 1.
Contents 1.0 Machine Overview 01 2.0 Packing Open and Installation 5.0. Menu Setting 21 5.1. Service Menu 22 5.1.1 Read Sensor Values 23 03 5.1.2 CIS Calibration 23 2.1 Packing List 03 5.1.3 MG/MT Waveforms 24 2.2 Installation and Use Location 04 5.1.4 Password Setting 24 2.3 Installation Instructions 05 5.1.5 Auto Diagnostic 25 2.3.1 Installation Warnings 05 5.1.6 PCS Counted and Reset 26 2.3.2 Power Supply Connection 05 5.1.7 Acquire CIS image 26 2.3.
1.0 Machine Overview Handle Banknote Guider TFT LCD Display Touch Panel Hopper Adjustable Screw Banknote Processing Wheel Impeller Stacker Figure 1 - 3 IMC01 Top Diagram Figure 1 - 1 IMC01 Front Diagram External Display Port USB Port Handle of Back Cover Speaker RS232 Printer Port Switch On/Off Power Cord Jack Figure 1 - 2 IMC01 Back Diagram IMC01 Banknote Counter User Manual Version 1.09 Page 01 Figure 1 - 4 IMC01 Side Diagram IMC01 Banknote Counter User Manual Version 1.
2.0 Packing Open and Installation 2.2 Installation and Use Location 2.1 Packing List As shown in figure 2-1, please stay away from the surrounding walls and reserve sufficient operation space for placement of banknotes, opening or closing of the cover plate, as well as for maintenance. When you receive the package, open and check the packing list in the package.
2.3 Installation Instructions 3.0 Display and Operation Interface 2.3.1 Installation Warnings 3.1 Display Appearance (1) This machine is specially designed for indoor use. Please do not install or use it outdoors. (2) Please do not install it in place that cannot bear the weight of this product or in places that are inclined or uneven. (3) Do not use or please combustible materials, inflammables and volatile items such as thinners around/inside this product.
4.0 Operating Instructions Detail key, to check the detail counted information. 4.1 Start-up Currency key, to select the one of currency, auto recognition or multi-currency mode for counting. Turn on the switch after connecting the machine to power supply. First, the machine enters the self-checking interface, as shown in Figure 4-1. Mode key, to select CNT mode, SDC mode or MDC mode for counting. CFD level key, to select the Counterfeit Detection Sensitivity level.
4.2 Selection of Counting Mode 4.2.1 Single Currency Counting Mode After the machine is turned on, the flag & currency graphic appears in the upper left corner, indicating that the machine is in the current currency counting mode. The default mode is MDC mode. By pressing the key of the control panel, three counting modes can be cyclically switched, and the 3 counting modes will be cyclically switched according to MDC-CNT-SDC sequence. Figure 4-5 Initial Interface of SDC Mode 4.2.1.
4.2.2 Automatic Recognition Mode In the process of counting banknotes, the IMC01 uses the first banknote passing through the sensor as the judgment rule to recognize the banknotes of all denominations of the same currency. When banknotes of other currencies are recognized, the machine will alarm and stop. At this time, banknotes from other currencies need to be taken out, and the machine will continue counting.
Example: Put a handful of banknotes (including USD, EUR, CAD, MXN) into the IMC01 hopper to count. The interface of the IMC01 displays as Figure 4-15 at the end of counting. Figure 4-16 Auto Banknote Detecting Off 4.3.2 SN Reading Figure 4-15 Multi-currency MDC Counting Result 4.2.4 Non-Volatile Memory for Currency Mode The currency mode setting is non-volatile.
The batch number will be increased by 10 by pressing the key , or decreased by 10 by pressing the key until it becomes 0. And it will be increased by 1 by pressing the key , or decreased by pressing the key . 4.3.4 Accumulation Press to enable the accumulation function. In any counting mode, the accumulation function of the number of the banknotes can be enabled by pressing the key . 4.3.
4.4 Counting Speed Setting 4.5.1 Check the Serial Number There are four counting speed options: 1500, 1200, 1000 and 800 (Note: 1500 and 1200 are the only optional in CNT mode). The default speed is 1000 in three modes. If setting is required, different counting speed can be switched by pressing the key in any counting mode. As shown in Figure 4-22, if the SN reading is on, press the key again, the banknote’s serial number will be shown in the following figure.
4.7 CFD Level 4.6.2 Data transfer to PC The data is transmitted to the computer for display through the DB9 serial cable. (1)Use the DB9 serial cable to connect the IMC01 to the computer, then turn on the computer. (2)Open the serial port tool (such as RS232 Hex Com Tool), select the serial port corresponding to the IMC01, and set the baud rate to 9600, as shown in the figure below. There are 3 adjustable CFD levels. By pressing the appearing in the upper right corner will change.
5.1 Service Menu 4.9 ORI Function To turn on the Face Function by long pressing the as shown in the following figure. key until a beep sound, Press the key to enter service menu, you will be requested to input a password with the following interface. The default password is 9999. Figure 4-29 ORI Function Note: After turning on the "ORI" function, the banknote counter will automatically stop and alarm when it detects that the side of the banknote is different from the previous banknote.
5.1.3 MG/MT Waveforms 5.1.1 Read Sensor Values Figure 5-4 Sensor Values Figure 5-6 MG/MT Waveforms As shown in Figure 5-4, the sensors values are only for engineer to check whether any sensor has a malfunction. If you meet any problem about use, please take a photo of this page and contact us. 5.1.4 Function Setting To enter the Function Setting interface by press the key, as shown in the following figure.
5.1.6 PCS Counted and Reset 5.1.4.2 WARNING BEEP Move the cursor to the WARNING BEEP option, press the MENU button to turn on or off the warnning beep. 5.1.4.3 BATCH NO CLEAR After turning on this setting, the data of the previous batch will not be clear, and will be accumulated to the next batch. 5.1.4.4 PC TERMINAL This feature is still in internal testing. 5.1.4.5 RJ OLD VER.
5.1.8 Detection Level 5.1.10 Unknown banknote This is for production and professional servicing purpose. 5.1.11 Back to Default setting As shown in Figure 5-13, press the menu key to reset all of the settings you changed before. Figure 5-11 CF Level As shown in Figure 5-11, you can use the left and right direction key to select, and up and down direction key to change the sensitivity levels. The currency code in the right part is indicating for which currency you are operating.
6.0 Software Upgrade 5.3 Time Setting USB Flash Drive upgrade method is adopted for the software upgrade of this product. Please upgrade the software according to the following steps. (1) The upgrade file needs to be moved to the root directory of the USB Flash Drive. (please do not change the file name or format of the upgrade file, and there cannot be two or more upgrade files in the root directory of the USB Flash Drive) (2) Insert the USB Flash Drive into the USB interface at the rear of the machine.
7.0 Maintenance (4) And program the file to the IMC01. After starting the machine, it will go on self-check automatically. If the preset window shows the error code or tell you to clean the sensors, generally speaking, it is because of dust on the surface or sensor blocked by notes. So please clear the dust on the surface with brush or soft cloth, or take the notes away. Then restart the machine. For more troubleshooting methods, please refer to the IMC01 maintenance manual.
8.0 Technical Parameters Table 8-1 Technical Parameters Counterfeit Detection Image (2 CIS Sensors), Magnetic, Infrared, Ultraviolet Double note detection, half note detection, Error Detection chain note detection US/CA version: USD, EUR, CAD, MXN, GBP Available currencies EU/UK version: EUR, USD, GBP, CHF, PLN, SEK, NOK, DKK Options Thermal printer connection Interfaces RS-232, 2 × USB, RJ12 LCD Display 3.
