M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-8188LCM 8x8 VGA-Audio Matrix Switcher Multi Video Matrix Switcher VGA-Audio Matrix Switcher Series Thank you for purchasing the SB-8188LCM VGA-AUDIO Matrix Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ...............................................................1 Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: FEATURES & SPECIFICATIONS ....................................2 FRONT PANEL .................................................................3 REAR PANEL ......................
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • • Supports 8x inputs VGA+Stereo Audio to 8x VGA+Stereo Audio outputs Matrix Switcher 8x Input signals support via VGA (RGBHV), Stereo Audio(AR/AL) 8x Output Signals support via VGA (RGBHV), Stereo Audio(AR/AL) to VGA Monitor displays Higher Video Bandwidth 450MB each path R,G,B signals.
FRONT PANEL FRONT PANEL 1. POWER SWITCH The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. INPUT STATUS DISPLAY Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input. 3.
FRONT PANEL FRONT PANEL 8. FUNCTION KEY - ALL Disables (mute) video on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected. Option 2 - Press ALL followed by Source 1 thru 8. The display will show the Source selected. - Press ENTER The pre-set source selection will be assigned all destinations. 9. FUNCTION KEY - OFF Disables (mute) video to selected channels.
FRONT PANEL FRONT PANEL 12. FUNCTION KEY - MEMORY The system will show stored presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location. - Configure desired matrices.. - Press MEMORY button. - Press 1 thru 8 on either Source or Destination row. - Press ENTER to ready memory location. - or press MEMORY again to cancel operation. Operation completes.
REAR PANEL REAR PANEL 1. DC POWER INLET The switcher is fitted with a DC power plug-park input connector. Please ensure that the plug-park used is of an approved type and is of sufficient current carrying capacity with the correct voltage and connector polarity. 12Volt DC power supply 2A Max. Power Jack: DC Jack - Inner OD ᴓ 2.1mm (+ ) Outside OD ᴓ 5.5mm (GND) Power input - 12VDC, 2A Switcher power suppler use universal Part number : TA 007 2. IR EXTERNAL IN (EXT.
REMOTE CONTROL Before making any connections to the switcher. Observe the following: Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%) Ensure that the power switch is OFF Ensure that all system grounds (earth) are connected to a common point.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES : CUSTOM CODE : 35CA POWER ON: POWER OFF: ALL: OFF: LOCK: RECALL: ENTER: MEMORY: 35CA 35CA 35CA 35CA 35CA 35CA 35CA 35CA A15E A25D B04F B14E B54A B24D B34C B44B PRESS DESTINATION - # then PRESS SOURCE - # DESTINATION #1 : 35CA 10EF DESTINATION #2 : 35CA 20DF DESTINATION #3 : 35CA 30CF DESTINATION #4 : 35CA 40BF DESTINATION #5 : 35CA 50AF DESTINATION #6 : 35CA 609F DESTINATION #7 : 35CA 708F DESTINATION #8 : 35CA
IR EXTENDER IR RECEIVER: 1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100) R oHS /95/E C IR E XT. in RS - 232 IR EXT . INP UT DC 12V 4 3 UT 4 -2 3 -4 UT IR 2 R IX IN P I MAT SW 1 HDM 1 S WIT UT 2 IN P 1 SB-100 C HE -3 R 3 UT ER 2 IN P P OW 2 ON 1 IN P IR Rx OFF -1 3 4 4 R S -232 SB-100 IR Receiver Set 2.
IR EXTENDER IR EMITTER: 1. SB-101 IR 300M Transmitter DC 12V Device Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set 2.
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0 For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual. Pin RS-232 Definition 1 ------ Not used 2 TX Transmitter 3 RX Receiver 4 ------ Not used 5 GND Ground 6 ------ Not used 7 ------ Not used 8 ------ Not used 9 ------ Not used RS-232 PROTOCOL COMMANDS ( RS-232 CONTROL DRIVER V2.0.
TYPICAL APPLICATION INSTALLING DIAGRAM 8X8 VGA-AUDIO MATRIX SWITCHER Sample connection using 8x8 VGA-AUDIO Matrix Switcher Switch signals to VGA-Audio Monitor Displays via VGA & Audio cable with SB-8188LCM and Audio Amplifier to speakers and signals from Satellite Receiver. NOTE: 1. Switch the Satellite Receiver signal Over VGA and Audio cable connect to monitors. 2. STB VGA/Audio signals switch Via SB-8188LCM VGA-Audio matrix switcher to VGA monitors. 3. SB-8188LCM matrix control via RS-232 by a pc.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM ED IA AUDIO A ND V IS UA L 122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.
