M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-3866 8x2 MultiVideo Switcher 8x2 HDMI & Analog Multi Video Format Scaler Routing Switcher MultiVideo to VGA Switcher Series Thank you for purchasing the SB-3866 MultiVideo To VGA Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this 8x2 Multivideo to VGA Switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: INTRODUCTION ...............................................................1 FEATURES & SPECIFICATIONS ....................................2 FRONT PANEL .................................................................
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • • Supports 8 A/V inputs to 2 VGA outputs Routing Switcher Support with Automatic format detection Input Signals NTSC (M.4.43), PAL(B,D,G,H,l,M,N,N-Com), PAL(60) and SECAM Video System Supports Composite Video, S-Video(Y/C) & Component 480i/p to SXGA Supports VGA output resolution VGA, SVGA, XGA and SXGA Signals switch including: 1. Composite Video/Stereo Audio 2. S-Video (Y/C)/Stereo Audio 3. Component Video (YPbPr, YCbCr, RGB)/Audio 4.
FRONT PANEL FRONT PANEL 1. POWER ON SWITCH The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power 2. INPUT SOURCES DISPLAY Input sources 1 to 8 LED illuminates green to indicate that a video source is present on that input. 3. SOURCE SELECT BUTTONS A separate output 1 and 2 source select buttons are provided for each destination.
BACK PANEL BACK PANEL 1. 2x VGA + AUDIO OUTPUTS: Two (2) VGA + Two (2) Audio outputs via RCA connector for audio and VGA output via DB-15p. # Output 1 - VGA-RGBHV / Stereo Audio # Output 2 - VGA-RGBHV / Stereo Audio 2. 2x 3.5mm AUDIO OUTPUTS: Provided same Stereo Audio outputs. 3. INPUT 7& 8 VGA-AUDIO INPUTS: Support VGA(RGBHV) & Stereo Audio Inputs.
REMOTE CONTROL Before making any connections to the SB-3866. Observe the following: Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%) Ensure that the power switch is OFF Ensure that all system grounds (earth) are connected to a common point.
IR EXTENDER REAR PANEL IR EXTENDER PORTS IR EXTENDER PACKAGE : HOW TO SETUP THE IR EXTENDER COMPONENTS 6
RS-232 SERIAL INTERFACE RS-232 The Shinybow switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system. Pin RS-232 Definition 1 ------ Not used 2 TX Transmitter The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1. When the unit recognizes a complete command it will perform the requested action - there is no delimiter character required.
OSD PICTURE ADJUSTMENT CONTENT Tint Brightness Allows adjustment to increase or decrease Tint. Adjusts back ground BRIGHTNESS black level of the screen image,low enough that a black area of the picture emits no light, but high enough that setting the control any higher would cause the area to become a dark gray. Contrast Sharpness Adjusts the foreground white level of the screen image. Allows adjustment to increase or decrease the Sharpness of the image. This function does not change Resolution.
OSD SETUP VGA OUTPUT RESOLUTIONS & VIDEO SOURCES SELECTIONS CONTENT Resolution Adjustment Changes the output resolution to one of the pre-set values. Note that after you make this change,your display device might need to re-clock to the signal. You can do this by changing your source input and then back again to the SB-3866 input. For example: If you have the SB-3866 connected to the VGA input on your projector.
OSD FUNCTION SETTING CONTENT Language Sleep Option to choose languages English or Chinese. The Sleep Timer will automatically shutdown the SB-3866 at a pre-determined amount of time. The preset values start at 10 minutes and goes to 120 minutes,in increments of 10 minutes ea. Reset Visibility Selecting Reset will restore the unit to factory default conditions. The input will default to CVBS-1 at its lowest resolution.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM EDIA AUDIO A ND V IS UA L 1399 Wildfire Lane | Frisco, TX 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.
