User guide

Part 1 – Commands for All Universal IP Devices Overview – Lists of Commands Grouped by Product
Universal IP AT Commands Reference Guide (Document S000457H) 16
Commands for MultiModem iCell (MTCMR-G/C/H/E)
#ACCEPT – Answer Incoming Call
#ANSWERMODE – Set Answering Mode
#APNPW – Access Point Name Password
#APNSERV – Access Point Name
#APNUN – Access Point User Name
#ATCMD – Set Default Dial Time AT Commands
#AUTHENT – Authentication Type
#AUTOCONNECT – Automatically Connect PPP Link
#AUTORESET – Reset Main Processor at a Given Time
#BODYi – Set Pre-Defined Email Combinations
#CALLBACKTIMER – Automatic Call-Back Wait
#CCRECi – Set Additional Recipient CC
#CONNECTIONSTART – Start Communication
#CONNECTIONSTOP – Stop Communication
#DELFLASH – Erase Flash Memory Parameter Values
#DIALN1 – Primary Dial-Up Number
#DIALN2 – Secondary Dial-Up Number
#DIALSELECT – Internet Connection Number
#DISPLAYIP – Display IP Addresses
#DLEMODE – Set DLE Mode
#DOMAIN – Set Domain Name of the Sender
#FTPAPPEND – Append Data to Server
#FTPGET – Download Files from FTP Server
#FTPGETFILENAME – Set FTP Download File Name
#FTPGETPATH – Path to Get Files from FTP Server
#FTPMODE – Enter FTP Mode
#FTPPORT – Enter FTP Server Port
#FTPPUT – Upload Files to FTP Server
#FTPPUTFILENAME – Set FTP Upload File Name
#FTPPW – Set FTP Password
#FTPSERV – Specify FTP Server Address
#FTPTYPE – Specify Data Type
#FTPUN – Set FTP User Name
#GETMAIL – Retrieve Host Mail
#GPIO – Enable/Disable and Configure External GPIO
Driven Events
#GPRSCID – PDP Context Identifier
#GPRSMODE – Switch Between GSM and GPRS
#ISPPW – ISP Password
#ISPUN – ISP User Name
#KEEPALIVEMODE – Keep-Alive Mode
#KEEPALIVEPORT – Keep-Alive Port Number
#KEEPALIVESERV – Keep-Alive Server Address
#LEGACYMODE – Legacy Mode Enable/Disable
#LTCPSTART – Open Listening Mode
#LTCPSTOP – Close TCP Listening Mode
#LUDPSTART – Initiate UDP Session in Listen Mode
#LUDPSTOP – Close UDP Listening Mode
#OTCP – Open a TCP Connection
#OUDP – Initiate UDP Session in Active Mode
#OUTPORT – UDP/TCP Local Port Number
#PERSISTENTSOCKET – Persistent Socket
#PHYTIMEOUT – Inactivity Timer
#PING – Start PING Request
#PINGDELAY – PING Delay Time
#PINGNUM – Number of PING Requests
#PINGREMOTE – IP Address of PING Request
#POP3HEADERMODE – POP3 Header
#POP3PW – Set POP3 Password
#POP3SERV – Set POP3 Server Address
#PPPMODE – TCP/IP Behavior
#PPPMYIP – IP Address When Using PPP
#PPPPEERIP – IP Address for Remote PPP
#PPPSERVPW – Remote PPP Client Password
#PPPSERVUN – User Name for Remote PPP Client
#PUTMAIL – Send Mail to Recipient w/ Interactive Mode
#RECiADD – Set Email Address
#RESET – Reset Main Processor or Internal Modem
#RINGCOUNT – Set Number of Rings
#SENDERADDR – Set Sender Address
#SENDERNAME – Set Sender Name
#SENDMAILi – Send Mail without Interactive Mode
#SMTPAUTH – Authentication ON or OFF
#SMTPPORT – Set SMTP Server Port
#SMTPPW – Set SMTP Password
#SMTPSERV – Set SMTP Server Address
#SMTPUN – Set SMTP User Name
#SUBJi – Set Email Pre-Defined Subject
#TCPPORT – Set TCP Port for Remote Peer
#TCPSERV – Set Address of Remote TCP Server
#TCPTXDELAY – Time Delay
#UDPPORT – UDP Port Number
#UDPSERV – UDP Server Address
#UDPTXDELAY – Sending UDP Datagram Delay
#VALL – Display All Parameters
#VFTP – Display FTP Parameters
#VMAILi – Display Email Parameters for Mail ID
#VPHY – Display Physical Parameters
#VPING – Display PING Parameters
#VPOP3 – POP3 Module Parameters
#VPPP – Display PPP Parameters
#VSMTP – Display SMTP Parameters
#VSTATE – Display State of Physical Connection
#VTCP – Display TCP Parameters
#VUDP – Display UDP Module Configuration
#VVERSION – Display Software Version
&C – RLSD (DCD) Option
&D – DTR Option
&F – Reset Factory Defaults
&S – DSR On or Off
&W – Store Factory Defaults to NVM
+
ICF – DTE-DCE Character Framing
+IFC – Set Flow Control
+IPR – Set Serial Speed
+WOPEN – Mode of Operation
AT – Command Mode
E – Turn Echo ON/OFF
I – Identification
V – Terse or Verbose
Z – Default Configuration