User guide

Part 1 – Commands for All Universal IP Devices Overview – Lists of Commands Grouped by Product
Universal IP AT Commands Reference Guide (Document S000457H) 11
Commands for SocketWireless Wi-Fi (MT810SWM-IP)
#AUTORESET – Reset Main Processor at a Given Time
#BODYi – Set Pre-Defined Email Combinations
#BOOTMSG – Enable/Disable Boot Message
#CCRECi – Set Additional Recipient CC
#DELFLASH – Erase Flash Memory Parameter Values
#DHCP – DHCP On or Off 46
#DLEMODE – Set DLE Mode 31
#DNSSERV1 – Set DNS Server IP Address 47
#DNSSERV2 – Set Secondary DNS Server 47
#DOMAIN – Set Domain Name of the Sender 19
#FTPAPPEND – Append Data to Server 30
#FTPGET – Download Files from FTP Server 29
#FTPGETFILENAME – Set FTP Download File Name 28
#FTPGETPATH – Path to Get Files from FTP Server 29
#FTPMODE – Enter FTP Mode 27
#FTPPORT – Enter FTP Server Port 27
#FTPPUT – Upload Files to FTP Server 29
#FTPPUTFILENAME – Set FTP Upload File Name 28
#FTPPUTPATH – Path to Send Files to the FTP Server 30
#FTPPW – Set FTP Password 28
#FTPSERV – Specify FTP Server Address 28
#FTPTYPE – Specify Data Type 27
#FTPUN – Set FTP User Name 28
#GETMAIL – Retrieve Host Mail 25
#IPADDR – Set Static IP Address 46
#IPDNSSERV – Configure the DNS Server 47
#IPDNSTABLE – Display DNS Table 49
#IPGATEWAY – Set Gateway Address 46
#IPNETMASK – Set Subnet Mask 47
#IPQUERY – Give a Domain Name 48
#IPRELEASE – Release DHCP Address 48
#IPRENEW – Renew DHCP Information from Server 48
#IPRESOLV – Observe -- Connection with DNS or Not 48
#LEGACYMODE – Legacy Mode Enable/Disable
#LTCPSTART – Open Listening Mode
#LTCPSTOP – Close TCP Listening Mode
#LUDPSTART – Initiate the UDP Session in Listen Mode
#LUDPSTOP – Close UDP Listening Mode
#OTCP – Open a TCP Connection
#OUDP – Initiate UDP Session in Active Mode
#OUTPORT – UDP/TCP Local Port Number
#PERSISTENTSOCKET – Persistent Socket
#PING – Start PING Request
#PINGDELAY – PING Delay Time
#PINGNUM – Number of PING Requests
#PINGREMOTE – IP Address of PING Request
#POP3HEADERMODE – POP3 Header
#POP3PW – Set POP3 Password
#POP3SERV – Set POP3 Server Address
#PUTMAIL – Send Mail to Recipient w/ Interactive Mode
#RECiADD – Set Email Address
#RESET – Reset Main Processor or Internal Modem
#SENDERADDR – Set Sender Address
#SENDERNAME – Set Sender Name
#SENDMAILi – Send Mail without Interactive Mode
#SMTPAUTH – Authentication ON or OFF
#SMTPPORT – Set SMTP Server Port
#SMTPPW – Set SMTP Password
#SMTPSERV – Set SMTP Server Address
#SMTPUN – Set SMTP User Name
#SUBJi – Set Email Pre-Defined Subject
#TCPPORT – Set TCP Port for Remote Peer
#TCPSERV – Set Address of Remote TCP Server
#TCPTXDELAY – Time Delay
#TELNET – Start/Stop Telnet Session
#TELNETPASSWORD – Set Telnet Password
#TELNETPORT – Set Telnet Port
#TELNETUSER – Set Telnet User
#UDPPORT – UDP Port Number
#UDPSERV – UDP Server Address
#UDPTXDELAY – Sending UDP Datagram Delay
#VALL – Display All Parameters
#VDNS – Display Configuration of DNS Servers
#VFTP – Display FTP Parameters
#VIP – View Address Settings
#VMAILi – Display Email Parameters for Mail ID
#VPING – Display PING Parameters
#VPOP3 – POP3 Module Parameters
#VSMTP – Display SMTP Parameters
#VSTATE – Display Current Physical Connection
#VTCP – Display TCP Parameters
#VTELNET – View Telnet Settings
#VUDP – Display UDP Module Configuration
#VVERSION – Display Software Version
#WATCHDOG – Enable/Disable Watchdog
#WATCHDOGTIMER – Watchdog Timer
#WEP? – View the Values of WEP Keys
#WEP128KEY – Keys for WEP128 Security Mode
#WEP64KEY – Keys for WEP64 Security Mode
#WEPKEYID – Set Default TX Key Index
#WLANACTIVATE – Move Module out of Power Save
#WLANASSOCINFO – Display Association Information
#WLANCONNECT – Connect with AP
#WLANCOUNTRYCODE – Country Code
#WLANDATARATE – WLAN Transmission Data Rate
#WLANDISCONNECT – Disconnect with AP
#WLANDOZE= – Moves Module into/out of Power Save
#WLANENABLE – Auto Connect Module with AP
#W
LANGETRSSI – Received Signal Strength
#WLANIBSSCHANNEL – Channel for Ad-Hoc Mode
#WLANNETWORKMODE – WLAN Network Mode
#WLANPOWERSAVE – Enable Power Save at Boot
#WLANPROFILE – Display the WLAN Profile
#WLANPROFILE – Load the WLAN Profile
#WLANPROFILEn=n – Change the WLAN Profile
#WLANROAM – Enable/Disable Roaming
#WLANSCAN – SCAN Wireless Networks
#WLANSCANMODE – Scanning Mode
#WLANSECURITYMODE – Security of WLAN Module
#WLANSSID – SSID of WLAN
#WLANUSEPROFILE – User Profile
#WPA2PSKKEY – Keys for WPA2 PSK Security Mode
#WPAPSKKEY – Keys for WAP PSK Security Mode
&C – RLSD (DCD) Option
&D – DTR Option
&F – Reset Factory Defaults
&S – DSR On or Off
&W – Store Factory Defaults to NVM
+ICF – DTE-DCE Character Framing
+IFC – Set Flow Control
+IPR – Set Serial Speed
A – Manual Answer of TCP or UDP
A/ – Previous Command
AT – Command Mode
E – Turn Echo ON/OFF
I – Identification
S0= – Automatic Answer
S2 – Escape Sequence
V – Terse or Verbose
Z – Default Configuration