User guide

Index
Universal IP AT Commands Reference Guide (Document S000457H) 105
#SENDERADDR – Set Sender Address 25
#SENDERNAME – Set Sender Name 25
#SENDMAILi – Send Mail without Interactive Mode 28
#SMTPAUTH – Authentication ON or OFF 30
#SMTPPORT – Set SMTP Server Port 27
#SMTPPW – Set SMTP Password 27
#SMTPSERV – Set SMTP Server Address 27
#SMTPUN – Set SMTP User Name 28
#SUBJi – Set Email Pre-Defined Subject Text 26
#TCPPORT – Set TCP Port for Remote Peer 38
#TCPSERV – Set Address of Remote TCP Server 39
#TCPTXDELAY – Time Delay 39
#TELNET – Start/Stop Telnet Session 59
#TELNETPASSWORD – Set Telnet Password 60
#TELNETPORT – Set Telnet Port 59
#TELNETUSER – Set Telnet User 59
#UDPPORT – UDP Port Number 42
#UDPSERV – UDP Server Address 42
#UDPTXDELAY – Delay before Sending UDP Datagram
42
#VALL – Display All Parameters 22, 23
#VAUTODISC – Display Auto Discover Commands 51
#VDNS – Display Configuration of DNS Servers 49, 56
#VFTP – Display FTP Parameters 37
#VIP – View Address Settings 49, 56
#VMAILi – Display Email Parameters for Mail ID 30
#VPHY – Display Physical Parameters 81
#VPING – Display PING Parameters 45
#VPOP3 – POP3 Module Parameters 33
#VPPP – Display PPP Parameters 81
#VSMTP – Display SMTP Parameters 30
#VSTATE – Display Current State of Physical Connection
22
#VTCP – Display TCP Parameters 41
#VTELNET – View Telnet Settings 60
#VUDP – Display UDP Module Configuration 43
#VVERSION – Display Software Version 22
#WEP? – View the Values of WEP Keys 67
#WEP128KEY – Keys for WEP128 Security Mode 66
#WEP64KEY – Keys for WEP64 Security Mode 65
#WEPKEYID – Set Default TX Key Index 66
#WLAN? – WLAN Module 68
#WLANACTIVATE – Move Module out of Power Save 65
#WLANASSOCINFO – Display Association Information68
#WLANCONNECT – Connect with AP 63
#WLANCOUNTRYCODE – Country Code 61
#WLANDATARATE – WLAN Transmission Data Rate 62
#WLANDISCONNECT – Disconnect with AP 63
#WLANDOZE= – Moves Module into/out of Power Save63
#WLANENABLE – Auto Connect Module with AP 63
#WLANGETRSSI – Received Signal Strength 65
#WLANIBSSCHANNEL – Channel for Ad-Hoc Mode 62
#WLANNETWORKMODE – WLAN Network Mode 61
#WLANPOWERSAVE – Enable Power Save at Boot 66
#WLANPROFILE – Display the WLAN Profile 67
#WLANPROFILE – Load the WLAN Profile 64
#WLANPROFILEn=n – Change the WLAN Profile 64
#WLANROAM – Enable/Disable Roaming 65
#WLANSCAN – SCAN Wireless Networks 64
#WLANSCANMODE – Scanning Mode 62
#WLANSECURITYMODE – Security Mode of WLAN
Module 61
#WLANSSID – SSID of WLAN 62
#WLANUSEPROFILE – User Profile 65
#WPA2PSKKEY – Keys for WPA2 PSK Security Mode 66
#WPAPSKKEY – Keys for WAP PSK Security Mode 66
&
&C – RLSD (DCD) Option 18
&D – DTR Option 18
&F – Reset Factory Defaults 18
&S – DSR On or Off 18
&W – Store Factory Defaults to NVM 19
+
+ICF – DTE-DCE Character Framing 19
+IFC – Set Flow Control 20
+IPR – Set Serial Speed 20
+WOPEN – Mode of Operation 70
A
A – Manual Answer of TCP or UDP 57
Access Point Name – #APNSERV 79
Access Point Name Password – #APNPW 79
Access Point User Name – #APNUN 79
Answer Incoming Call – #ACCEPT 76
Append Data to Server – #FTPAPPEND 37
AT – Command Mode 17
Authentication ON or OFF – #SMTPAUTH 30
Authentication Type – #AUTHENT 70
Auto Connect Module with AP – #WLANENABLE 63
Auto Discovery On or Off – #AUTODISC 50
Auto Discovery Port – #AUTODISCPORT 50
Auto Discovery Timer – #AUTODISCTIMER 50
Automatic Answer – S0= 55
Automatic Call-Back Wait – #CALLBACKTIMER 71
Automatically Connect PPP Link – #AUTOCONNECTION
78
C
Call Retry Delay – #REDIALDELAY 73
Caller ID – #CALLSCREENNUM 71
Change the WLAN Profile – #WLANPROFILEn=n 64
Channel for Ad-Hoc Mode – #WLANIBSSCHANNEL 62
Close TCP Listening Mode – #LTCPSTOP 40
Close UDP Listening Mode – #LUDPSTOP 43
Command Mode – AT 17
D
Default Configuration – Z 18
Delay before Sending UDP Datagram – #UDPTXDELAY
42
DHCP On or Off – #DHCP 47, 53
Disconnect with AP – #WLANDISCONNECT 63
Display All Parameters – #VALL 22, 23
Display Association Information – #WLANASSOCINFO68
Display Auto Discovery Commands – #VAUTODISC 51
Display Configuration of DNS Servers – #VDNS 49, 56
Display Current State of Physical Connection – #VSTATE
22
Display DNS Table – #IPDNSTABLE 56
Display Email Parameters for Mail ID – #VMAILi 30
Display FTP Parameters – #VFTP 37
Display IP Addresses – #DISPLAYIP 80
Display Physical Parameters – #VPHY 81
Display PING Parameters – #VPING 45
Display PPP Parameters – #VPPP 81
Display SMTP Parameters – #VSMTP 30