User guide

Part 1 – Commands for All Universal IP Devices Overview – Lists of Commands Grouped by Product
Universal IP AT Commands Reference Guide (Document S000457H) 10
Overview – Lists of Commands
Grouped by Product
Commands for SocketEthernet IP (MT100SEM-IP)
#AUTODISC – Auto Discovery On or Off
AUTODISCHOST – Auto Discovery Host Name
#AUTODISCPASSWORD – Auto Discovery Password
#AUTODISCPORT – Auto Discovery Port
#AUTODISCTIMER – Auto Discovery Timer
#AUTODISCUSERNAME – Auto Discovery User Name
#BODYi – Set Pre-Defined Email Combinations
#CCRECi – Set Additional Recipient CC
#DELFLASH – Erase Flash Memory Parameter Values
#DHCP – DHCP On or Off
#DLEMODE – Set DLE Mode
#DNSSERV1 – Set DNS Server IP Address
#DNSSERV2 – Set Secondary DNS Server
#DOMAIN – Set Domain Name of the Sender
#EMACSPD – Set Netmask Address
#ETHIFSTATUS – View Network Interface Settings
#FTPAPPEND – Append Data to Server
#FTPGET – Download Files from FTP Server
#FTPGETFILENAME –FTP Download File Name
#FTPGETPATH – Path to Get Files from FTP Server
#FTPMODE – Enter FTP Mode
#FTPPORT – Enter FTP Server Port
#FTPPUT – Upload Files to FTP Server
#FTPPUTFILENAME – FTP Upload File Name
#FTPPUTPATH – Path to Send Files to the FTP Server
#FTPPW – Set FTP Password
#FTPSERV – Specify FTP Server Address
#FTPTYPE – Specify Data Type
#FTPUN – Set FTP User Name
#GETMAIL – Retrieve Host Mail
#IPADDR – Set Static IP Address
#IPGATEWAY – Set Gateway Address
#IPNETMASK – Set Subnet Mask
#LTCPSTART – Open Listening Mode
#LTCPSTOP – Close TCP Listening Mode
#LUDPSTART – Initiate the UDP Session in Listen Mode
#LUDPSTOP – Close UDP Listening Mode
#OTCP – Open a TCP Connection
#OUDP – Initiate UDP Session in Active Mode
#OUTPORT – UDP/TCP Local Port Number
#PING – Start PING Request
#PINGDELAY – PING Delay Time
#PINGNUM – Number of PING Requests
#PINGREMOTE – IP Address of PING Request
#POP3HEADERMODE – POP3 Header
#POP3PW – Set POP3 Password
#POP3SERV – Set POP3 Server Address
#PUTMAIL – Send Mail to Recipient w/ Interactive Mode
#RECiADD – Set Email Address
#SENDERADDR – Set Sender Address
#SENDERNAME – Set Sender Name
#SENDMAILi – Send Mail without Interactive Mode
#SMTPAUTH – Authentication ON or OFF
#SMTPPORT – Set SMTP Server Port
#SMTPPW – Set SMTP Password
#SMTPSERV – Set SMTP Server Address
#SMTPUN – Set SMTP User Name
#SUBJi – Set Email Pre-Defined Subject
#TCPPORT – Set TCP Port for Remote Peer
#TCPSERV – Set Address of Remote TCP Server
#TCPTXDELAY – Time Delay
#TELNET – Start/Stop Telnet Session
#TELNETPASSWORD – Set Telnet Password
#TELNETPORT – Set Telnet Port
#TELNETUSER – Set Telnet User
#UDPPORT – UDP Port Number
#UDPSERV – UDP Server Address
#UDPTXDELAY – Delay before Sending UDP Datagram
#VALL – Display All Parameters
#VAUTODISC – Display Auto Discover Commands
#VDNS – Display Configuration of DNS Servers
#VFTP – Display FTP Parameters
#VIP – View Address Settings
#VMAILi – Display Email Parameters for Mail ID
#VPING – Display PING Parameters
#VPOP3 – POP3 Module Parameters
#VSMTP – Display SMTP Parameters
#VTCP – Display TCP Parameters
#VTELNET – View Telnet Settings
#VUDP – Display UDP Module Configuration
#VVERSION – Display Software Version
&C – RLSD (DCD) Option
&D – DTR Option
&F – Reset Factory Defaults
&S – DSR On or Off
&W – Store Factory Defaults to NVM
+ICF – DTE-DCE Character Framing
+IFC – Set Flow Control
+IPR – Set Serial Speed
AT – Command Mode
E – Turn Echo ON/OFF
I – Identification
V – Terse or Verbose
Z – Default Configuration