Specifications

HYLAFAX-CONFIG(5F) HYLAFAX-CONFIG(5F)
ModemDTRDropDelay integer 75 delay (ms) between DTR OFF and DTR ON
ModemEchoOffCmd string ATE0 command for disabling command echo
ModemFlowControl string XONXOFF DTE-DCE flowcontrol scheme
ModemFrameFillOrder string LSB2MSB bit order for HDLC frames
ModemHardFlowCmd string −command for setting hardware flowcontrol between DTE and
ModemMinSpeed string 2400 minimum acceptable transmit speed
ModemMfrQueryCmd string −command for querying modem manufacturer
ModemModelQueryCmd string −command for querying modem model
ModemNoAutoAnswerCmd string ATS0=0 command for disabling auto-answer
ModemNoAutoAnswerCmdDelay integer 0 time, in ms, to pause after a disabling auto-answer
ModemNoFlowCmd string −command for disabling hardware flowcontrol between DTE and
ModemOnHookCmd string ATH0 command for placing phone ‘‘on hook’’
ModemPageDoneTimeout integer 180000 page send/receive timeout (ms)
ModemPageStartTimeout integer 180000 page send/receive timeout (ms)
ModemRaiseATCommands boolean Yes raise ATcommands in configuration to upper-case
ModemRate integer 19200 baud rate to use for DCE-DTE communication
ModemReadyCmds string −additional final commands when resetting modem
ModemRecvFillOrder string see below bit order for receivedfacsimile data
ModemRecvSuccessCmd string −command to send after a successful reception
ModemResetCmds string −additional commands when resetting modem
ModemResetDelay integer 2600 delay (ms) after placing DTR ON
ModemResultCodesCmd string ATQ0 command for enabling result codes
ModemRevQueryCmd string see below command for querying modem firmware revision
ModemSendBeginCmd string −command to send on establishing carrier
ModemSendFillOrder string LSB2MSB bit order for sending facsimile data
ModemSetVolumeCmd string see below commands for setting modem speaker volume level
ModemSetupAACmd string −command for setting up adaptive answer
ModemSetupDCDCmd string −command for setting up DCD handling
ModemSetupDTRCmd string −command for setting up DTR handling
ModemSoftFlowCmd string −command for setting software flowcontrol between DTE and DCE
ModemSoftResetCmd string ATZ command for doing a soft reset
ModemSoftResetCmdDelay integer 3000 time, in ms, to pause after a soft reset
ModemSoftRTFCC boolean Yes enable software-drivenreal-time fax compression conversion
ModemType string see below modem type
ModemVerboseResultsCmd string ATV1 command for enabling verbose result codes
ModemWaitForConnect boolean No force server to wait for ‘‘CONNECT’’ response on answer
ModemWaitTimeCmd string ATS7=60 command for setting time to wait for carrier when dialing
FaxT1Timer integer 35000 CCITT T.30 T1 timer (ms)
FaxT2Timer integer 7000 CCITT T.30 T2 timer (ms)
FaxT4Timer integer 3100 CCITT T.30 T4 timer (ms)
Class0Cmd string AT+FCLASS=0 Class 0: command to enter class 0
Class1Cmd string AT+FCLASS=1 Class 1: command to enter class 1
Class1Cmd string AT+FCLASS=1.0 Class 1.0: command to enter class 1
Class1AdaptRecvCmd string −Class 1/1.0: command for adaptive reception support
Class1ColorJPEGSupport boolean No Class 1/1.0: to enable color JPEG fax support
Class1EnableV34Cmd string −Class 1/1.0: command to enable V.34-fax support
Class1ECMSupport boolean Yes Class 1/1.0: enable T.30-A ECM support
Class1PersistentECM boolean Yes Class 1/1.0: to continue to correct while in ECM
Class1ECMFrameSize integer 256 Class 1/1.0: image frame size in ECM protocol
Class1ExtendedRes boolean −Class 1/1.0: enable extended resolution support
Class1HasRHConnectBug boolean No Class 1/1.0: modem can report CONNECT incorrectly
Class1HFLOCmd string −Class 1/1.0: command to set hardware flowcontrol
Class1FrameOverhead integer 4 Class 1/1.0: extra bytes in a received HDLC frame
$Date$ 4