User guide

ManualsBrandsMultitech ManualsComputer equipmentMT5634ZLXE

MultiModem®ZPX

MT5634ZPX

Internal ISA Data/Fax Modem

Quick Start Guide

Summary of content (12 pages)

PAGE 1
MultiModem®ZPX MT5634ZPX Internal ISA Data/Fax Modem Quick Start Guide
PAGE 2
MT5634ZPX Quick Start Guide Quick Start Guide MT5634ZPX -V92 Internal ISA Data/Fax Modem 82084605L, Rev F This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2007 by Multi Tech Systems, Inc. Multi-Tech Systems, Inc.
PAGE 3
MT5634ZPX Quick Start Guide Product Description ® The MultiModem ZPX is an internal, half-length, data/fax modem card that can be plugged into any ISA expansion slot. It incorporates the ITU-T-V.92 protocol which provides quick connections, downstream transmissions at speeds up to 56 Kbps*, and downstream transmissions at speeds up to 46Kbps when connected to V.92 compatible Internet service providers.
PAGE 4
MT5634ZPX Quick Start Guide Step 1 - Determine System Resources Before you physically install your new MultiModem, you need to determine what system resources are in use on yur system. The best way to check what resources are in use and which ones are available, run WINMSD Utility. 1. 2. 3. 4. 4 To check the system resources, click Start I Run. Enter WINMSD in the Open: window and click OK. The operating system then displays the System Information dialog box.
PAGE 5
. 6. 7. 8. MT5634ZPX Quick Start Guide The MultiModem only uses IRQs 3,4,and 5 so you need to check in the above screen to see if any of these IRQs are available. The MultiModem is defaulted to IRQ 5. Record the available IRQ that you are going to use _____. Now, click on I/O to display the available I/O addresses. The MultiModem uses the following I/O addresses: COM1: 3F8-3FF COM2: 2F8-2FF COM3: 3E8-3EF COM4: 2E8-2EF and is defaulted to COM 4.
PAGE 6
MT5634ZPX Quick Start Guide Step 2 - Configure Jumpers The MT5634ZPX board contains seven Berg jumpers for setting the interrupt request (IRQ) number and COM port assignment. The jumpers are located on the lower part of the PC board as shown below. The IRQ number is set using jumpers 1, 2, and 3 and the COM port assignment is set using jumpers 4 through 7. The default IRQ number is IRQ5 and the default COM port assignment is COM4. PC Board Jumpers 1. 2. 3.
PAGE 7
MT5634ZPX Quick Start Guide 2. 3. 4. 5. 6. Remove the cover from the computer as instructed in the computer manual. Select an empty ISA expansion slot. Remove the expansion slot cover and save the retaining screw. Place the MultiModem directly above the expansion slot and gently, but firmly, push it into the connector until the card’s retaining bracket is flush against the computer chassis. Fasten the retaining bracket to the computer chassis with the screw saved in step 3.
PAGE 8
MT5634ZPX Quick Start Guide 12. Click Finish in the Completing the Add Hardware Wizard window and Windows wants to restart your computer in order for the changes to take effect. Click Yes. 13. After the system reboots, verify that your com port is available and your IRQ is correct by selecting the Control Panel I System and clicking on the Hardware tab in the System Properties screen. 14. Click on the Device Manager button. Click on the Ports (COM & LPT) to display the Communications Ports.
PAGE 9
MT5634ZPX Quick Start Guide 4. The modem response will be displayed in the Command I Response window of the MT5634ZPX-V92 Properties screen. Step 7 - Connect Your Modem to the Telephone Line The MultiModem communicates over public-switched telephone network lines. Use the modular telephone cable provided with the modem to connect the MultiModem to your telephone wall jack.
PAGE 10
MT5634ZPX Quick Start Guide The Global Wizard Utility The Global Wizard configuration utility is recommended for computers running Windows 98 or newer. 1. Insert the MultiModem CD into the CD-ROM drive. The Autorun menu should appear. 2. Click Initial Setup and Country Selection. 3. In the Global Wizard dialog box, select either Run from CD or Install on your PC. Choose the former to configure your modem without installing the Global Wizard on your computer.
PAGE 11
MT5634ZPX Quick Start Guide Data Communications Software Data communications software is designed to send and receive messages. MultiTech includes a data communications software with your modem. However, the modem will work with most data communications software. To install the software, insert the CD into the CD-ROM drive; click the Phone Tools icon.You will be asked to choose your language. The software automatically loads onto your PC.
PAGE 12
Patents This device is covered by one or more of the following patents: 6,031,867; 6,012,113; 6,009,082; 5,905,794; 5,864,560; 5,815,567; 5,815,503; 5,812,534; 5,809,068; 5,790,532; 5,764,628; 5,764,627; 5,754,589; D394,250; 5,724,356; 5,673,268; 5,673,257; 5,644,594; 5,628,030; 5,619,508; 5,617,423; 5,600,649; 5,592,586; 5,577,041; 5,574,725; D374,222; 5,559,793; 5,546,448; 5,546,395; 5,535,204; 5,500,859; 5,471,470; 5,463,616; 5,453,986; 5,452,289; 5,450,425; D361,764; D355,658; D355,653; D353,598; D353,1