Specifications

Index
Multi-Tech Systems, Inc. SocketModem MT5600SMI/MT5656SMI Reference Guide (S000306B) 112
Index
+
+VLS Command Options Table .....................................104
3
32-bit frame check sequence command +EFCS ...............31
A
Analog Source/Destination Selection +VLS...................104
answer command A ..........................................................18
AT commands.....................................................................4
definition ........................................................................4
format .............................................................................4
AT Commands
E – Compromise Equalizer Enable Command.........45
#UD – Last Call Status Report .....................................40
$F – FastConnect Control.............................................46
%7 – Plug and Play Serial Number ................................8
%8 – Plug and Play Vendor ID and Product Number.....9
%C – Enable/Disable Data Compression .....................37
%E – Enable/Disable Line............................................29
%L - Report Line Signal Level.....................................22
%Q – Report Line Signal Quality.................................22
%U – Select µ Law or A-Law Codec Type..................29
&C – RLSD (DCD) Option..........................................13
&D – DTR (Data Terminal Ready) Option ..................13
&F – Restore Factory Configuration ..............................7
&G – Select Guard Tone ..............................................19
&K – Flow Control ......................................................13
&L – Leased Line Operation........................................45
&P – Select Pulse Dial Make/Brake Ratio ...................19
&R – RTS/CTS (Request to Send/Clear to Send) Option
.................................................................................14
&S – DSR (Data Set Ready) Override .........................14
&T – Local Analog Loopback Test................................8
&V – Display Current Configuration & Stored Profiles
.................................................................................20
&V1 – Display Last Connection Statistics ...................21
&W – Store Current Configuration ................................8
&Y – Designate a Default Reset Profile.........................8
&Z – Store Telephone Number ......................................8
)M – Enable Cellular Power Level Adjustment............45
** - Load Flash Memory ................................................9
@M – Initial Cellular Power Level ..............................45
+A8E – V.8 and V.8bis Operation Controls.................38
+A8I – CI Signal Indication .........................................39
+DR – Data Compression Reporting............................37
+DS – Data Compression .............................................35
+DS44 – V.44 Compression Select ..............................35
+EB – Break Handling Error Control...........................31
+EFCS – 32-bit Frame Check Sequence ......................31
+ER – Error Control Reporting ....................................32
+ER – Report Current Error Control ............................32
+ES – Error Control and Synchronous Mode Selection30
+ESR – Selective Reject...............................................31
+ETBM – Call Termination Buffer Management........ 33
+FCLASS – Select Active Service Class....................... 5
+GCAP – Request Complete Capabilities List .............. 7
+GCI – Country of Installation ...................................... 7
+GMI – Request Manufacturer ID................................. 7
+GMM – Request Model ID.......................................... 7
+GMR – Request Revision ID....................................... 7
+IFC – DTE Modem Local Flow Control.................... 15
+ILRR – DTE Modem Local Rate Reporting.............. 15
+IPR – Fixed DTE (Data Terminal Equipment) Rate.. 14
+MCR – Report Syntax Command.............................. 28
+MR – Modulation Reporting Control ........................ 28
+MRR .......................................................................... 28
+MS – Modulation Selection....................................... 26
+PCW – Call Waiting Enable...................................... 47
+PIG – PCM Upstream Ignore..................................... 49
+PMH – Modem on Hold Enable ................................ 47
+PMHF – V.92 Modem on Hold Hook Flash.............. 49
+PMHR – Initiate Modem on Hold ............................. 48
+PMHTR – Modem on Hold Timer............................. 48
+PQC – V.92 Phase 1 and 2 Control............................ 49
+PSS – Use Short Sequence ........................................ 50
+QCPC – Force Full Startup Procedure....................... 50
+VCID – Caller ID ........................................................ 5
+VRID – Report Retrieved Caller ID (CID).................. 6
A - Answer................................................................... 18
B – Communication Standard Setting.......................... 29
\B – Transmit Break to Remote ................................... 33
D 16
E – Command Echo ..................................................... 11
H – Disconnect (Hang-up)........................................... 18
I - Identification ............................................................. 6
\K – Break Control....................................................... 34
-K – MNP Extended Services ...................................... 34
L – Speaker Volume .................................................... 19
M – Speaker Control.................................................... 19
\N – Operating Mode-Error-Correction ......................... 6
O – Return to Online Data Mode................................. 18
P – Set Pulse Dial Default............................................ 17
Q – Quiet Result Code Control.................................... 11
-QCPS – Enable Quick Connect .................................. 50
-STE – Set Telephony Extension................................. 23
T – Set Tone Dial Default............................................ 17
V – Result Code Form ................................................. 11
\V – Single Line Connect Message Enable.................. 22
W – Connect Message Control .................................... 11
X – Extended Result Codes ......................................... 12
Z – Soft Reset and Restore Profile................................. 5
Autoanswer ........................................................................ 4
Autoanswer S0 ................................................................. 51
Automatic Hang up Control +VNH ............................... 100
B
Backspace character, setting S5 ....................................... 51
Beep Tone Duration Timer +VTD ................................. 109
bit mapped options status - S28........................................ 54
bit mapped options status - S31........................................ 54
break control command \K............................................... 34