Owner`s manual

PN 88300150
4/3/01 84
&L4D selects 4 wire Originate mode operation
&Mn n = 0 or 1 *** &M0 means Async when on-line.
&M1 means Sync when on-line.
$MIn** n = 0 or 1 *** $MI0 disables MI/MIC option (**)
$MI1 enables MI/MIC option (**)
$MBn n = speed $MB75 selects ITU-T V.23 mode.
$MB300 selects 300 bps on-line.
$MB1200 selects 1200 bps on-line.
$MB2400 selects 2400 bps on-line.
$MB4800 selects 4800 bps on-line.
$MB9600 selects 9600 bps on-line.
$MB14400 selects 14400 bps on-line.
$MB19200 selects 19200 bps on-line.
$MB24000 selects 24000 bps on-line.
$MB28800 selects 28800 bps on-line.
*** $MB33600 selects 33600 bps on-line.
Nd d = 0 thru 9 Dial stored telephone number "d". Do not include the letter D with this command.
NdNe d = 0 thru 9 Number Linking. If first number dialed is busy, another stored number may be
e = any other automatically dialed. For example, stored number "d" is dialed, and if busy, stored
number 0-9 number "e" is dialed.
O Exit Command Mode and go into On-Line Mode.
P *** Modem will pulse-dial numbers following the P.
&Pn** n = 0 or 1 *** &P0 means 60-40 pulse ratio.
&P1 means 67-33 pulse ratio.
#Pn n=0 thru 2 *** #P0 means no parity.
#P1 means odd parity.
#P2 means even parity.
Qn n = 0 or 1 *** Q0 means Result Codes sent.
Q1 means Result Codes will be suppressed (quiet).
Q2 means Dumb Answer Mode.
&Qn n = 0 or 1 *** &Q0 selects Multi-Tech command set.
&Q1 selects AT command set.
Rn n = 0 or 1 *** R0 means modem will not reverse modes.
R1 means modem will reverse modes.
&Rn n = 0, 1 or 2 &R0 lets Clear to Send act normally.
*** &R1 forces Clear to Send on.
&R2 drops for S24 period on disconnect.
*Rn n = 0 or 1 *** *R0 disables ring message on callback modem.
*R1 enables ring message on callback modem.
&RFn n = 0 or 1 &RF0 selects CTS follows RTS.
*** &RF1 selects CTS to act independently.
$Rn n = 0 or 1 *** $R0 means disconnect after 12 retransmits.
$R1 means do not disconnect after 12 retransmits.
Sr=n r = 0 thru 11, Sets value of Register “r” to value of “n”,
13, 17-19, 24, where “n” is entered in Decimal format.
25, 30, 32, 34
Sr? r = 0 thru 11, Reads value of Register “r” and displays
13, 17-19, 24, value in 3-digit Decimal format.
25, 30, 32, 34
$SBn n = speed $SB1200 selects 1200 bps at serial port.
$SB2400 selects 2400 bps at serial port.
$SB4800 selects 4800 bps at serial port.
$SB9600 selects 9600 bps at serial port.
$SB19200 selects 19,200 bps at serial port.
$SB38400 selects 38,400 bps at serial port
$SB57600 selects 57600 bps at serial port.
*** $SB115200 selects 115200 bps at serial port.
&Sn n = 0, 1 or 2 &S0 forces Data Set Ready On.
*** &S1 lets Data Set Ready act normally.
&S2 Data Set Ready drop is regulated by S24 on disconnect.
&SFn n = 0 or 1 *** &SF0 selects DSR follows CD.