User manual

03/03 11 - 16 DS 2.501A
SECTION 3 – MODEM INITIALIZATION FOR SATCHNET
The modems listed here are only for use with Satchnet Software.
For details of Modems supported for other Invensys products please
contact your local Invensys agent.
The modem(s) must be initialized with the correct command string.
The initialization (command) string can be set from the
communications icon of Satchnet Pro or the modem(s) can be
configured from a separate communications package.
If the modem is only to be used with Satchnet, then the AT&W
command can be used to fix the configuration in the modems non
volalite memory. The AT&F command is used to reset the modem to
its factory default settings.
The AT&F and AT&W should not be included in the Satchnet
initialization string.
AT&F and AT&W should be sent to the modem when it is first installed
to ensure the factory defaults are set in the modem.
SUPPORTED PAGERS
BRITISH TELECOM TAP PROTOCOL
British Telecom Message Master pager
British Telecom tone Master pager
The BT pager computer telephone number is 0345 581 354
The pager ID number is derived from the pager telephone number
(supplied with the pager). To derive the pager ID take the last 6 digits
from the pager telephone number and put a 0 at the front of the 6 digits.
REMOTE PRINTER MODEM INITIALIZATION
The remote printer modem must be setup using a terminal programme
running on a PC. The following modem settings are required:-
1. Baud rate set to 1200.
2. DTR to control line connection i.e. when DTR inactive, line drops.
3. Autoanswer mode activated (AT S0 = 1).
4. Quiet mode (AT Q1).
PACE, LINNET 12 & 24
Compatible with:- Satchnet 6.1 onwards
MIU
Command string: None required. Factory default.
Notes: Beware of exchanges that have internal ring tones in excess of
1second, the Linnet 24 will not always answer.
PACE, LINNET QUAD FX AND MICROLIN FX
Version 2.02 or later. Contact Pace if you have an earlier version.
Compatible with:- Satchnet 6.1 onwards
MIU
Command string: AT &S1 &K0 \N0 %C0
When a FAX is used &K6 may be written to the Modem. AT &K0 will
have to be written back to the Modem for use with Satchnet.
PACE, MICROLIN FX32 PLUS
Compatible with:- Satchnet 6.11 onwards
Command string:- None required. Factory default.
HAYES SMARTMODEM, QUAD
Compatible with:- Satchnet 6.1 onwards
MIU
Command string:- AT &C1 &D2
HAYES SMARTMODEM, OPTIMA 24
Compatible with:- Satchnet Plus (6.20) onwards
MIU
Command string: AT &C1 &D2 &Q0
DOWTY, QUATTRO
Compatible with:- Satchnet 6.1 onwards
MIU
Command string: AT &C1 &D2 &K0 &S0
MULTI TECH, MT1432M
Compatible with:- Satchnet 6.1 onwards
MIU
Command string: None required. Factory default.
US ROBOTICS SPORTSTER 14,400/PC FAX
Internal fax/modem card.
Compatible with:- Satchnet Plus (6.20) onwards
Command string: &B1 &A0 &K0
Bit Switch Settings (Default)
1 – Up
2 – Up
3 – Down
4 – Up
5 – Down
6 – Up
7 – Up
8 – Down
PSION, BULLDOG
Compatible with:- Satchnet 6.21 onwards
Command string: AT %D1 B0 &G2 &P1 S6=5 S8=5 S7=59
S11=70 X4
AT 4&D2 &C1
PACE, MOBI FAX 144
Compatible with:- Satchnet 6.21 onwards
Command string: AT &K0
AT F4
MULTI TECH, MT1932ZDXK
Compatible with:- Satchnet 6.21 onwards and MIU
Command string: AT &F
AT &E0 &E3 &E14 #F0$MB1200
&Q1$SB1200X4
AT &W
MEGAHERTZ USA FAX MODEM
Compatible with:- Satchnet Plus onwards
Command string:- AT &K0 F4
PACE, MOBIFAX 24
Compatible with:- Satchnet Plus (6.20) onwards
MIU
Command string:- None required.
Factory default
US ROBOTICS SPORTSTER VI
Compatible with:- Satchnet Plus onwards
MIU
Command string:- AT &A0 &K0 &M0 &N2 &H0 &R1 &S1
RS COMPONENTS 9000 SERIES
Compatible with:- Satchnet Plus (6.20) onwards
Command string:- AT &C1 &D2 &G2 &Q6 &S1
LASAT SAFIRE 144
Compatible with:- Satchnet Plus (6.20) onwards
Command string:- AT &F
AT &K0 %C0 F4 \N1
AT &W
PACE, LINNET 34
Compatible with:- Satchnet Plus (6.20) onwards
Command string:- AT &C0 \N0 &K0
US ROBOTICS Vi 14.4 28.8
Compatible with:- Satchnet Plus (6.20) onwards
Command string:- AT &F
AT &A0 &K0 &M0 &N2 &H0 &R1 &S1
AT &W
Example: Pager telephone number 0893 123456
Pager ID is 0123456