MultiAccess® ACS Analog Communications Server MA100-1M User Guide
MultiAccess ACS User Guide MA100-1M PN S000351D, Version D Copyright This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2009, by Multi-Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
Table of Contents Table of Contents Chapter 1 – Product Description & Specifications .................................................................................. 5 Product Description ................................................................................................................................... 5 Features .................................................................................................................................................... 5 Package Contents ..........
Table of Contents Canadian Limitations Notice .................................................................................................................... 40 Industry Canada ...................................................................................................................................... 40 Safety and EMC Product Approvals ........................................................................................................
Chapter 1 – Product Description and Specifications Chapter 1 – Product Description & Specifications Product Description The MultiAcces ACS single-port communications server provides connectivity to the corporate LAN for telecommuters and mobile users, or to remotely installed equipment, via one integrated V.92/56K modem.
Chapter 1 – Product Description and Specifications Package Contents The MultiAccess package contains: • One MultiAccess ACS • One universal power supply with power cord • One mounting bracket • Four adhesive-backed rubber feet for table-top mounting • One Quick Start Guide • One product CD Handling Precautions All Devices must be handled with certain precautions to avoid damage due to the accumulation of static charge.
Chapter 2 – Installation Chapter 2 – Installation Attaching the MultiAccess ACS to a Fixed Location The MultiAccess is design to be used on the desktop or to be panel-mounted. To attach the bracket for panel-mounting, following these steps: 1. Typically, the MultiAccess is mounted against a flat surface with two mounting screws. Drill the 15 mounting holes at the desired location. The mounting holes must separated by 4 /16 inches centerto-center. Screw Separation 41516 inches 2.
Chapter 2 – Installation MultiAccess ACS Connections The MT100-1M is supplied power through an external power supply. 1. Plug the DC power transformer into the power outlet or power strip. Secure the other end to the PWR on your MultiAccess. The DC power transformer is included with your MultiAccess. Caution: Use only the DC power transform supplied with the MA100-1M. Use of any other transformer voids the warranty and can damage the unit. 2.
Chapter 3: Configuring your MultiAccess ACS Chapter 3 – Configuring Your MultiAccess ACS Setting Admin PC to Startup IP Address 1. Connect a PC to your network. Record the original PC’s IP address before you change it. 2. Set the PC IP address to 192.168.2.x subnet (using any address excluding 192.168.2.1). Logging In 1. Bring up a Web browser on your PC. At the browser’s address line, type the default address of the MA100-1M: http://192.168.2.1 and press Enter. 2. The Login screen will appear.
Chapter 3: Configuring your MultiAccess ACS Setting MA100-1M IP Addresses 1. In the MA100-1M Administration screen, go to the IP Configuration fields. 2. Fill in the IP information that applies to your MA100-1M unit. The fields for “IP Address,” “Subnet Mask,” “Default Gateway” and “Name Server” are required. A “Secondary Name Server” is optional. 3. Click Update. After the Update button has been clicked, it takes 5 seconds for the MA100-1M to update the addresses.
Chapter 3: Configuring your MultiAccess ACS Setting Up the Mail Server 1. From the Administration screen, go to the SMTP Configuration fields. 2. Enter the mail server address in the SMTP Server Address window (e.g., mail.multitech.com or IP address). 3. Enter the SMTP Port (usually 25) that is used as the SMTP Server. 4. Enter the E-mail address of the administrator in the Administrator E-mail window. 5. If the SMTP Server requires a User ID, enter the ID in the SMTP Server User ID window. 6.
Chapter 3: Configuring your MultiAccess ACS Local Authentication. A valid set of credentials, defined in the Local User data base, is required before access is granted. Radius Authentication. A valid set of credentials, defined in the Radius User data base, is required before access is granted. Raw Mode with No Authentication. User data is treated “as is”, without interpretation, and no authentication is required. Raw Mode with Local Authentication.
Chapter 3: Configuring your MultiAccess ACS Setting Authentication Authentication Type option defines where the database of user credentials reside. Local Authentication refers to the Local User Database on the MultiAccess. Radius Authentication refers to a user database controlled by a Radius Server outside the MultiAccess. If a Radius Server is used for authentication, then the server has to be configured to receive requests from the MA100-1M.
Chapter 3: Configuring your MultiAccess ACS Setting Up Local Users The administrator builds the Local Users data base defining the Name field, recording the User ID, Password entries, and callback method. The administrator account has both administration of the MA1001M and dial-in rights. The user accounts only have rights to use the modem. The remote user enters their user ID and password during the dial-in session. For Local Authentication, go to the Local Users screen.
Chapter 4: Software Chapter 4 – Software In this chapter, we present the screens of the MultiAccess ACS software. We describe each field in each screen and some of the command buttons. (We do not describe command buttons that have functions that would be readily understood by users of Windows software. Examples of such self-evident functions include buttons like “OK,” “Cancel,” “Next,” etc.) Home Screen The MultiAccess Home screen offers access to all other MultiAccess software screens.
Chapter 4: Software Login Screen The MultiAccess Login screen is the primary security Device for the Server software. The MultiAccess has a default setting that allows use of “admin” as both the User Name and the Password at initial startup. After you have begun configuring your MultiAccess, you should change the password in the Local Users screen for the administrator account described later in this chapter. Multi-Tech Systems, Inc.
Chapter 4: Software Call Log Screen The Call Log screen displays the parameters you can set for the Call Log entries and displays a call log entry for each call. The Log Parameters define the threshold number of entries and the number of entries retained in the log history.
Chapter 4: Software Call Log Call Log Field Definitions Column Call Type Time Username Rate Values Data mm/dd/yyyy Description Data call is the only type of call supported by MultiAccess. Time that call was sent or received. alphanumeric The name of the user generating or receiving the call. 33,600; 31,200; 28,800; 26,400; 24,000; 21,600; 19,200; 16,800; 14,400; 12,000; 9600; 7200; 4800; 2400; 1200; 0-300 bps The data call transmission speed in bits per second at which the current call occurred.
Chapter 4: Software Current Status Screen Current Status Field Definitions Field Name Values Description System group Current Time Pending Messages Email To: Subject: Time Server Status weekday, mo, dd hh:mm:ss yyyy numeric Alphanumeric in email name format Alphanumeric Initializing, No Errors, SNTP Error: type Multi-Tech Systems, Inc. MultiAccess ACS User Guide The present time of day. Emails sent to the administrator that have not been opened.
Chapter 4: Software Field Name Current Status Field Definitions (cont’d) Values Description System group x days yy hours: zz minutes Up Time Email Status No Errors, Bad MailServer Address, Mail Server Connect Failed, SMTP Invalid Response, SMTP Client Timeout Operation time since last reboot. Indicates whether the MultiAccess’s email transmissions, both calls and administrative messages, are proceeding with or without errors.
Chapter 4: Software Administration Screen The Administration Screen sets up the network addressing of the MultiAccess, communication with the SMTP name server, and defines the time stamp for the MultiAccess. Administration Screen Field Definitions Field Name Values Description IP Configuration Fields IP Address n.n.n.n The IP address of the MultiAccess. Subnet Mask n.n.n.n This subnet mask is the subnet for the network to which the MultiAccess is connected.
Chapter 4: Software Administration Screen Field Definitions Field Name Values Description IP Configuration Fields Update (button) Click on this button to make changes to IP Configuration fields take effect. SMTP Configuration Fields SMTP Server Address Domain name or IP address for mail server (SMTP must be supported on mail server). SMTP Port Numeric The default SMTP Port number is 25. Administrator E-mail Alphanumeric in email name format The administrator’s email address.
Chapter 4: Software Local Users Data Base Screen The administrator builds the Local Users data base defining the Name field, recording the User ID, Password entries, and callback method. The administrator account has both administration of the MA1001M and dial-in and dial-out rights. The user accounts have dial-in and dial-out rights to use the modem. The remote user enters their user ID and password at the beginning of the dial-in session.
Chapter 4: Software Modem Setup The Modem Setup screen defines the Modem Sharing behavior and general modem parameters, Country Code and number of rings before auto answer. Prior to software release 1.03, the ports were configured for either RAS or modem sharing, for which they were then dedicated to just that role. Now, with software release 1.03, the ports can be configured for both roles, alleviating the need for administrator intervention when either role is desired.
Chapter 4: Software Authentication Screen If the authentication method is Radius, then the IP address of the Radius server and Radius Accounting Server have to be entered and the user credentials are handled by the Radius server. If the authentication method is local, the Local User Database defines the user credentials. For RAS calls, dial-in PPP, a second static IP address is needed in the Remote Host Address field. This address is for the dial-in user, PPP peer.
Chapter 5: Troubleshooting Chapter 5 – Troubleshooting What if I can’t see the web page for my MultiAccess? REMEDY: Is the PWR LED on the MultiAccess unit blinking? If not, then the unit is either malfunctioning or not turned on. If the PWR LED is flashing as a heart beat, then verify that the Admin PC is actually on the same subnet as the MultiAccess and that it can be “pinged.” Launch a Command Prompt. (In WinNT, go to Start | Programs | Command Prompt.
Chapter 5: Troubleshooting CAUSE C: The client PC running the mail software cannot connect to the mail server. RESPONSE C: If you, as a client, cannot send yourself an email, then contact your administrator; there may be a problem with your mail server. If the Radius server shows the auth request was rejected? CAUSE: The shared secret is wrong (case sensitive), the user is giving the wrong password, or the user doesn’t have appropriate rights.
Appendix A – Device Manager Utility Appendix A – Device Manager Utility The Device Manger utility is used to synchronize phonebooks/local user data bases, backup and restore a configuration, and update firmware in a MultiAccess ACS unit and its accompanying POTS modem. The Device Manager utility can manage multiple MultiAccess ACS units on the same network and on other networks as long as the manager has access to that network.
Appendix A – Device Manager Utility Adding a Device to the Manager In order for the Device Manager to recognize a MultiAccess ACS unit, the MA100-1M must be added to the manager. The Device Manager can manage multiple MA100-1M as long as the Device Manager has access to that network. 1. To launch the Device Manager program from the Windows desktop, go to Start | Programs | Multi-Tech Device Manager I Multi-Tech Device Manager. The Device Manager main screen will appear. 2.
Appendix A – Device Manager Utility Set Local User Sharing Local user sharing must be set up per unit before local user data bases can be synchronized. When MultiAccess ACS local users are synchronized, all data bases contain the same user crentials except for the administrator accounts. One MultiAccess ACS unit (the Primary unit) holds the master list that is transmitted (using the Synchronize Phonebooks/Local Users command) to other MultiAccess ACS units on the network (Copy units).
Appendix A – Device Manager Utility Synchronize Phonebooks/Local Users When MultiAccess ACS Local Users data bases are synchronized, all non-administrative listings match. One MultiAccess ACS unit (primary unit) holds the master data base that is transmitted to other remote units on the network (copy units). MultiAccess ACS units can operate on the network, but have independent Local Users, in which case they are designated as Independent. Independent units are ignored during synchronization. 1.
Appendix A – Device Manager Utility Updating Firmware Over time, new versions of MultiAccess ACS firmware will be issued. When these newer versions become available, you will want to secure the firmware files (typically by downloading them from the MultiTech web site) and install them on the MultiAccess ACS. There are two parts to a full firmware update: (a) Updating POTS Modem 1 firmware (with file name of the form dwqg.
Appendix A – Device Manager Utility In the bottom (and largest) pane of the Update MultiAccess ACS n.n.n.n window, read the list and write down the version of firmware currently in use for the POTS modem. Compare the version with the update file that you plan to use. Make sure that the file to be installed really does supersede the one currently installed. 3. In the MultiAccess ACS Update Select field, select the POTS Modem 1 to update. 4. Browse to the location of the most recent firmware file. 5.
Appendix A – Device Manager Utility 7. The updating process will take as long as a minute. During this time, several messages will appear in the Update MultiAccess ACS N.N.N.N window. A transient TFTP screen may appear briefly. If the updating process has been successful, the final message line will say “Finished – The MultiAccess ACS is ready.” 8. The updating process is now complete. Click the “X” in the upper-right corner to return to the main Device Manager screen. Multi-Tech Systems, Inc.
Appendix A – Device Manager Utility MultiAccess ACS Firmware Update 1. In the Device column of the Device Manager screen, identify the MultiAccess ACS unit on which the update is to be done. Be sure that the Status of that MultiAccess ACS unit is idle before continuing. (You cannot update the MultiAccess ACS while it is handling a call.) Select that MultiAccess ACS unit and right-click on it. In the menu that appears, select Update. 2. The Update MultiAccess ACS N.N.N.N screen will appear.
Appendix A – Device Manager Utility 4. Browse to the location of the most recent firmware file. 5. Click Start Update. 6. The MultiAccess ACS – Confirm Update screen will appear. Click OK. Multi-Tech Systems, Inc.
Appendix A – Device Manager Utility 7. The updating process will take as long as a minute. During this time, several messages will appear in the Update MultiAccess ACS N.N.N.N window. A transient TFTP screen may appear briefly. If the updating process has been successful, the final message line will say “Finished – The MultiAccess ACS is ready.” 8. Close the Update MultiAccess ACS N.N.N.N window. In the main Device Manager window, the updated version will be listed. 9.
Appendix B – Regulatory Information Appendix B – Regulatory Information 47 CFR Part 68 Telecom 1. This equipment complies with Part 68 of the 47 CFR rules and the requirements adopted by the ACTA. Located on this equipment is a label that contains, among other information, the registration number and ringer equivalence number (REN) for this equipment or a product identifier in the format: For current products is US:AAAEQ##Txxxx. For legacy products is AU7USA-xxxxx-xx-x.
Appendix B – Regulatory Information 12. Manufacturing Information: Manufacturer: Multi-Tech Systems, Inc. Trade Name: MultiAccess ACS Model Number: MA100-1M Registration No: AU7USA-25814-M5-E Ringer Equivalence: 0.3B Modular Jack (USOC): RJ11C or RJ11W (single line) Service Center in USA: Multi-Tech Systems, Inc. 2205 Woodale Drive Mounds View, MN 55112 U.S.A.
Appendix B – Regulatory Information Canadian Limitations Notice Notice: The ringer equivalence number (REN) assigned to each terminal Device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of Devices subject only to the requirement that the sum of the ringer equivalence numbers of all the Devices does not exceed 5. Notice: The Industry Canada label identifies certified equipment.
Appendix C – WEEE Statement Appendix C – Waste Electrical and Electronic Equipment (WEEE) Statement July, 2005 The WEEE directive places an obligation on EU-based manufacturers, distributors, retailers and importers to take-back electronics products at the end of their useful life. A sister Directive, ROHS (Restriction of Hazardous Substances) complements the WEEE Directive by banning the presence of specific hazardous substances in the products at the design phase.
Appendix D – C-ROHS HT/ST Substance Concentration Appendix D – C-ROHS HT/TS Substance Concentration 依照中国标准的有毒有害物质信息 根据中华人民共和国信息产业部 (MII) 制定的电子信息产品 (EIP) 标准-中华人民共和国《电子信息产品污染控制管理办法》(第 39 号),也称作中国 RoHS,下表列出了 Multi-Tech Systems Inc.
Appendix E – MCSI2000 Parameters Appendix E – MCSI2000 Parameters Setting Up MCSI2000 Com Port Redirector Add one MCSI2000 com port to your workstation. Reboot the workstation. The properties of the MCSI2000 com port should be: • Connect Time = 0 • Direct (Not MAG) • Use Line Defaults Yes • Server IP address is that of the MultiAccess • Protocol Telnet • Port Number 7000 • Authentication No.
Appendix F – Modem AT Commands Appendix F – Modem AT Commands AT Commands Command: Values: Description: AT Command: Values: Description: Attention Code N/A The attention code precedes all command lines except A/, A: and escape sequences. ENTER Key N/A Press the ENTER (RETURN) key to execute most commands. Command: Values: Description: A Answer N/A Answer call before final ring. Command: Values: Description: A/ Repeat Last Command N/A Repeat the last command string.
Appendix F – Modem AT Commands Command: Values: Default: Description: Ds Dial s = dial string (phone number and dial modifiers) none Dial telephone number s, where s may up to 40 characters long and include the 0–9, *, #, , B, C, and D characters, and the L, P, T, V, W, S, comma (,), semicolon (;), !, @, ^ and $ dial string modifiers. Dial string modifiers: L Redial last number. (Must be placed immediately after ATD.) P Pulse-dial following numbers in command.
Appendix F – Modem AT Commands Command: Values: Default: Description: In Information Request n = 0–5, 9, 11 None I0 Display default speed and controller firmware version. I1 Calculate and display ROM checksum (e.g., 12AB). I2 Check ROM and verify the checksum, displaying OK or ERROR. I3 Display default speed and controller firmware version. I4 Display firmware version for data pump (e.g., 94).
Appendix F – Modem AT Commands Command: Values: Default: Description: Sr=n Set Register Value r = S-register number; n varies None Set value of register Sr to value of n, where n is entered in decimal format (e.g., S0=1). Command: Values: Default: Description: Sr? Read Register Value r = S-register number None Read value of register Sr and display it in 3-digit decimal form (e.g., S2? gives the response 043).
Appendix F – Modem AT Commands Command: Values: Default: Description: &Cn Data Carrier Detect (DCD) Control n = 0, 1, 2 1 &C0 Forces the DCD circuit to be always ON. &C1 DCD goes ON when the remote modem’s carrier signal is detected, and goes OFF when the carrier signal is not detected. &C2 DCD turns OFF upon disconnect for time set by S18. It then goes high again (for some PBX phone systems).
Appendix F – Modem AT Commands Command: Values: Defaults: Description: &Ln Leased Line Operation n = 0, 1, or 2 0 &L0 The modem is set for standard dial-up operation. &L1 The modem is set for leased line operation in originate mode. &L2 The modem is set for leased line operation in answer mode. Note: For &L1 and &L2, there is a 30-second window between power up and the starting of the leased line handshake. During this time, you can turn off the command, if desired.
Appendix F – Modem AT Commands Command: Values: Default: Description: &Wn Command: Values: &Zy=x Store Dialing Command y = 0–2 (0–1SMI-Parallel {internal}) x = Dialing command None Stores dialing command x in memory location y. Dial the stored number using the command ATDS=y. See Also the #CBS command, a callback security command.
Appendix F – Modem AT Commands Command: Values: Default: Description: \Kn Break Control n = 0–5 5 Controls the modem's response to a break received from: computer, remote modem, or \B command. Response is different for each of three different states. Data mode. Modem receives the break from the computer: \K0 Enter online command mode, no break sent to the remote modem. \K1 Clear data buffers and send break to the remote modem. \K2 Same as \K0. \K3 Send break immediately to the remote modem.
Appendix F – Modem AT Commands Command: Values: Default: Description: \Xn XON/XOFF Pass-Through n = 0 or 1 0 \X0 Modem responds to and discards XON/XOFF characters. \X1 Modem responds to and passes XON/XOFF characters. Note: This is also controlled via &E6 and &E7. Command: Values: Defaults: Description: -Cn Data Calling Tone n = 0 or 1 1 -C0 Disable V.25 data calling tone to deny remote data/fax/voice discrimination. -C1 Enable V.25 data calling tone to allow remote data/fax/voice discrimination.
Appendix F – Modem AT Commands Command: Values: Default: Description: %Rn Cisco Configuration n = 0, 1 0 %R0 Disables Cisco configuration. %R1 Sets E0, Q1, &D0, \N0, $SB9600, and %S1 for operation with a Cisco router. Command: Values: Default: Description: %Sn Command Speed Response n = 0, 1 0 %S0 Sets modem to respond to AT commands at all normal speeds. %S1 AT commands accepted at 115200 bps only. Commands at other speeds are ignored.
Appendix F – Modem AT Commands Command: Values: Default: Description: +VDR=x, y Distinctive Ring Report x = 0, 1 Distinctive Ring report control. See description. y = 0–255 Minimum ring interval in 100 ms units. See description. 0, 0 Enables reporting of ring cadence information to the DTE and specifies the minimum ring cadence that will be reported. The report format is one line per silence period and one line per ring period.
Appendix F – Modem AT Commands Command: Values: Default: Description: #CBAn Callback Attempts n = 1–255 4 Sets the number of callback attempts that are allowed after passwords have been exchanged between modems. Command: Values: Default: Description: #CBDn Callback Delay n = 0–255 15 Sets the length of time (in seconds) that the modem waits before calling back the remote modem.
Appendix F – Modem AT Commands Command: Values: Default: Description: #CBRy Callback Security Reset y = 0–29 None Clears the password and phone number in the y memory location. Command: Values: Default: Description: #CBSn Callback Enable/Disable n = 0, 1, 2, or 3 0 #CBS0 Disables callback security. #CBS1 Enables local and remote callback security. #CBS2 Enables remote callback security only. #CBS3 Disables callback security until local hang-up or reset.
Appendix F – Modem AT Commands Escape AT Commands Command: Values: Description: +++AT Escape Sequence N/A Puts the modem in command mode (and optionally issues a command) while remaining online. Type +++AT and up to six optional command characters; then press ENTER. Used mostly to issue the hang-up command: +++ATH. Command: Values: Description: %%%ATMTSMODEM Remote Configuration Escape Sequence N/A Initiates remote configuration mode while online with remote modem.
Appendix F – Modem AT Commands V.92 Commands Command: Values: Defaults: Description: +MS= Modulation Selection See description. See description. This extended-format command selects modulation, enables or disables automode, and specifies the highest downstream and upstream connection rates using one to four subparameters. The command syntax is +MS=[mod][,[automode][,[0][,[max_rate][,[0][,[max_rx_rate]]]]]] Subparameters that are not entered retain their current value.
Appendix F – Modem AT Commands max_rate An optional number that specifies the highest rate at which the modem may establish an upstream (transmit) connection. The value is decimal coded in units of bps, for example, 33600 specifies the highest rate to be 33600 bps. 0 Maximum rate determined by the modulation selected in mod (default). 300–33600 Maximum rate value limited by the modulation selected in mod. For valid max_rate values for each mod value, see the following table.
Appendix F – Modem AT Commands Command: Values: Default: Description: +PMHF V.92 Modem Hook Flash N/A N/A Causes the DCE to go on-hook for a specified period of time, and then return off-hook for at least a specified period of time. The specified period of time is normally one-half second, but may be governed by national regulations. Command: Values: Default: Description: +PQC=n Quick Connect Control n = 0, 1, 2, or 3 3 Controls V.92 shortened Phase 1 and Phase 2 startup procedures (Quick Connect).
Appendix F – Modem AT Commands Command: Values: Default: Description: #CBAn Callback Attempts n = 1–255 4 Sets the number of callback attempts that are allowed after passwords have been exchanged between modems. Command: Values: Default: Description: #CBDn Callback Delay n = 0–255 15 Sets the length of time (in seconds) that the modem waits before calling back the remote modem.
Appendix F – Modem AT Commands Command: Values: Default: Description: #CBSn Callback Enable/Disable n = 0, 1, 2, or 3 0 #CBS0 Disables callback security. #CBS1 Enables local and remote callback security. #CBS2 Enables remote callback security only. #CBS3 Disables callback security until local hang-up or reset. Command: Values: Default: Description: #Pn Set 11-bit Parity n = 0 or 1 2 #P0 No parity. #P1 Odd parity. #P2 Even parity.
Appendix F – Modem AT Commands S-Registers Certain modem values, or parameters, are stored in memory locations called S-Registers. Use the S command to read or to alter the contents of S-Registers (see previous section). Register Unit S0 1 ring Range 0, 1–255 Default 1 Description Sets the number of rings until the modem answers. ATS0=0 disables auto answer completely. S1 1 ring 0–255 0 Counts the rings that have occurred.
Appendix F – Modem AT Commands S37 decimal 0–19 0 S38 decimal 0–23 1 S43 decimal 0–1 1 Sets the maximum V.34 “upstream” speed at which the modem attempts to connect. 0 = maximum speed 1 = reserved 2 = 1200/75 bps 3 = 300 bps 4 = reserved 5 = 1200 bps 6 = 2400 bps 7 = 4800 bps 8 = 7200 bps 9 = 9600 bps 10 = 12000 bps 11 = 14400 bps 12 = 16800 bps 13 = 19200 bps 14 = 21600 bps 15 = 24000 bps 16 = 26400 bps 17 = 28800 bps 18 = 31200 bps 19 = 33600 bps Sets “downstream” data rate where V.
Appendix F – Modem AT Commands S48 decimal 7 or 128 7 Enables (7) or disables (128) LAPM negotiation. The following table lists the S36 and S48 configuration settings for certain types of connections.
Appendix F – Modem AT Commands Result Codes In command mode your modem can send responses called Result Codes to your computer. Result codes are used by communications programs and can also appear on your monitor.
Appendix F – Modem AT Commands 114 115 116 CONNECT 54666 CONNECT 25333 CONNECT 26666 Connected at 54666 bps Connected at 25333 bps Connected at 26666 bps * EC is added to these result codes when the extended result codes configuration option is enabled. EC is replaced by one of the following codes, depending on the type of error control connection: V42bis – V.42 error control (LAP-M) and V.42bis data compression V42 – V.
Index Index 1 10/100Baset Ethernet, 7 4 47 CFR Part 15 regulations, 46 5 56K operation digital loss when used with PBX S108, 74 A Abort timer ‐ S7, 71 Adaptive Answer Result Code Enable command ‐ %A, 59 Add Time Server, 26 Administration Screen, 25 Administrator, 16 Administrator E-mail, 26 Answer command ‐ A, 51 Asynchronous Communications Mode command ‐ &Q, 56 Asynchronous Word Length ‐ $EB, 61 AT Command Control command ‐ %DC, 59 AT commands #CBA – Callback Attempts, 63 #CBD – Callback Delay, 63 #CBF
Index Blacklist command, 59 Break Control command ‐ \K, 58 Break Signal, 58 C Call Details, 22 Call Log entries, 20 Call Log screen, 20 Call Type, 22 call waiting, 67 Call Waiting Enable command ‐ +PCW=, 67 Callback Attempts command ‐ #CBA, 63, 69 Callback Delay command ‐ #CBD, 63 Callback Delay command #CBD, 69 Callback Enable/Disable command ‐ #CBS, 64 Callback Enable/Disable command #CBS, 70 Callback Failed Attempts Display command ‐ #CBF?, 63 Callback Failed Attempts Display command #CBF?, 69 Callback
Index L Leased Line Operation command ‐ &L, 56 LED Indicators, 7 Line feed character ‐ S4, 71 Load Factory Settings command ‐ &F, 55 Local Callback Inactivity Timer command ‐ #CBI, 69 Local Callback Inactivity Timer command #CBI – Local Callback Inactivity Timer, 63 Log History, 20 Log Parameters, 20 Login Screen, 19 Logout, 24 Loopback Test commands ‐ &T, 56 M MA100‐1M, 10 MNP 5 data compression, 59 MNP Error Correction, 58 MNP® Class 5, 7 Modem on Hold Enable command ‐ +PMH=, 67 Modem Reset command ‐ Z,
Index S9 – Remote Configuration Escape Character, 71 setting, 54 Standby mode delay time S89, 74 State, 24 Store Callback Password command ‐ #CBN=, 63, 69 Store Dialing command ‐ &Z – Store Dialing Command, 57 Store Setup Password command ‐ #S, 70 Store Setup Password command ‐ #S=, 64 Subject, 23 Subnet Mask, 25 T Time, 22 Time Server, 26 Time Server Status, 23 Time Zone, 26 Tone Dialing command ‐ T, 54 Tones ‐ S11, dialing, 71 Transmit Break command ‐ \B, 57 U Up Tim, 24 upstream mode, 67 Upstream V.