User guide
Table Of Contents
- Contents
- 1-1 About This Manual
- 1-2 System Specifications
- 1-3 Safety Precautions
- 2-1 List of Jumpers and Connectors
- 2-2 Component Locations
- 2-3 How to Set Jumpers
- 2-4 COM Port Connector
- 2-5 RS232/422/485 (COM2) Selection
- 2-6 IRQ12 Release Selection
- 2-7 ATX Power Signal Connector
- 2-8 ATX Power Button
- 2-9 AT/ATX Power Selection
- 2-10 Universal Serial Bus Connector
- 2-11 Solid-State Disk Socket
- 2-12 SSD Memory Map Selection
- 2-13 Keyboard / PS2 Mouse Selection
- 2-14 Keyboard / PS2 Mouse Connector
- 2-15 External Keyboard Connector
- 2-16 Reset Connector
- 2-17 Hard Disk Drive LED Connector
- 2-18 CPU Fan Connector
- 2-19 System Fan Connector
- 2-20 External Speaker Connector
- 2-21 Floppy Disk Drive Connector
- 2-22 Hard Disk Drive Connector
- 2-23 VGA CRT Connector
- 2-24 LCD Panel Connector
- 2-25 LCD VDD Selection
- 2-26 Panel Power Connector
- 2-27 Printer Connector
- 2-28 Power LED & Keylock Connector
- 2-29 LAN Connector
- 2-30 LAN LED Indicators
- 2-31 Green Function Connector
- 2-32. Memory Installation
- 3-1. Introduction
- 3-2. VGA Driver Utility
- 3-3. Flash BIOS Update
- 3-4. LAN Driver Utility
- 3-5. Watchdog Timer Configuration
- 4-1. Power Saving Block Diagram
- 4-2. CPU Doze Mode
- 4-3. System Standby Mode
- 4-4 System Suspend Mode
- 5.1 Introduction
- 5-2 Entering Setup
- 5-3 Standard CMOS Setup Menu
- 5-4 BIOS Features Setup Menu
- 5-5 Chipset Features Setup
- 5-6 Power Management Setup
- 5-7 PnP/PCI Configuration
- 5-8 Load BIOS Defaults
- 5-9 Load Setup Defaults
- 5-10 Integrated Peripherals
- 5-11 Password Setting
- 5-12 IDE HDD Auto Detection
- PC-104 Connector Pin Assignment
- ISA Bus Pin Assignments
- PCI Bus Pin Assignments
- C-1 Introduction
- C-2 Troubleshooting with Error Messages
74 CommPlete Series 4000 Server SBC, Model IPC-623C
Award BIOS Setup
5-12 IDE HDD Auto Detection
The parameters presented on this menu are pre-set at the
factory. They should be altered only by expert users.
When you select IDE HDD AUTO DETECTION from the
CMOS
Setup Utility
menu, this screen will appear:
ROM / PCI / ISA BIOS (2A69KP6A)
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
Note: Some OSes (like SCO-UNIX) must use Normal for installation
Esc: Skip
Primary Master :( Mb)
Primary Slave :
Secondary Master :
Secondary Slave
:
CYLS.
0
HEADS
0
PRECOMP
0
LANDZONE
0
SECTORS
0
MODE
--------
Select Secondary Slave Option (N=Skip) :N
Option
2(Y)
1
3
Size
540
541
540
Cyls
524
1049
524
Heads
32
16
32
Precomp
0
65535
65535
Landzone
1048
1048
1048
Sectors
63
63
63
Mode
LBA
Normal
LARGE
Figure 5-9: IDE HDD Auto Detection Screen
This setup menu allows you to save time in finding the Hard
Disk Drive information, just follow the following steps:
1. Select the “IDE HDD AUTO DETECTION” from the main
menu.
2. After a couple of seconds, the screen will appear with the
Hard Disk information and the following message will appear:
“SELECT PRIMARY MASTER OPTION (N=SKIP):N”
3. Enter Y or N to confirm the acceptance of the parameter
reported by the BIOS, then press the ENTER key.
The process will repeat again for the Primary Slave, Secondary
Master and Secondary Slave Hard Disks.