User guide
Table Of Contents
- Contents
- 1-1 About This Manual
- 1-2 System Specifications
- 1-3 Safety Precautions
- 2-1 List of Jumpers and Connectors
- 2-2 Component Locations
- 2-3 How to Set Jumpers
- 2-4 COM Port Connector
- 2-5 RS232/422/485 (COM2) Selection
- 2-6 IRQ12 Release Selection
- 2-7 ATX Power Signal Connector
- 2-8 ATX Power Button
- 2-9 AT/ATX Power Selection
- 2-10 Universal Serial Bus Connector
- 2-11 Solid-State Disk Socket
- 2-12 SSD Memory Map Selection
- 2-13 Keyboard / PS2 Mouse Selection
- 2-14 Keyboard / PS2 Mouse Connector
- 2-15 External Keyboard Connector
- 2-16 Reset Connector
- 2-17 Hard Disk Drive LED Connector
- 2-18 CPU Fan Connector
- 2-19 System Fan Connector
- 2-20 External Speaker Connector
- 2-21 Floppy Disk Drive Connector
- 2-22 Hard Disk Drive Connector
- 2-23 VGA CRT Connector
- 2-24 LCD Panel Connector
- 2-25 LCD VDD Selection
- 2-26 Panel Power Connector
- 2-27 Printer Connector
- 2-28 Power LED & Keylock Connector
- 2-29 LAN Connector
- 2-30 LAN LED Indicators
- 2-31 Green Function Connector
- 2-32. Memory Installation
- 3-1. Introduction
- 3-2. VGA Driver Utility
- 3-3. Flash BIOS Update
- 3-4. LAN Driver Utility
- 3-5. Watchdog Timer Configuration
- 4-1. Power Saving Block Diagram
- 4-2. CPU Doze Mode
- 4-3. System Standby Mode
- 4-4 System Suspend Mode
- 5.1 Introduction
- 5-2 Entering Setup
- 5-3 Standard CMOS Setup Menu
- 5-4 BIOS Features Setup Menu
- 5-5 Chipset Features Setup
- 5-6 Power Management Setup
- 5-7 PnP/PCI Configuration
- 5-8 Load BIOS Defaults
- 5-9 Load Setup Defaults
- 5-10 Integrated Peripherals
- 5-11 Password Setting
- 5-12 IDE HDD Auto Detection
- PC-104 Connector Pin Assignment
- ISA Bus Pin Assignments
- PCI Bus Pin Assignments
- C-1 Introduction
- C-2 Troubleshooting with Error Messages

60 CommPlete Series 4000 Server SBC, Model IPC-623C
Award BIOS Setup
5-5 Chipset Features Setup
Choose CHIPSET FEATURES SETUP from the
CMOS Setup
Utilities
menu, the following screen appears.
Esc: Quit
F1: Help
F5: Old Values
F6: Load BIOS Defaults
F7: Load Setup Defaults
Pu/Pd/+/-: Modify
(Shift) F2: Color
:Select Item
ROM / PCI / ISA BIOS (2A69KP6A)
BIOS FEATURES SETUP
AWARD SOFTWARE, INC.
Auto Configuration :Enable
EDO DRAM Speed Selection : :60 ns
EDO CASx# MA Wait State :2
EDO RASx# Wait State :2
SDRAM RAS-to-CAS Delay :3
SDRAM RAS Precharge Time :3
SDRAM CAS Latency Time :3
SDRAM Precharge Control :Disabled
DRAM Data Integrity Mode :Non-ECC
System BIOS Cacheable :Disabled
Video BIOS Cacheable :Disabled
Video RAM Cascheable :Disabled
8-Bit I/O Recovery Time :1
16-Bit I/O Recovery Time :1
Memory Hole at 15M-16M :Disabled
Passive Release :Enabled
Delayed Transaction :Disabled
AGP Aperture Size (MB) :64
Power-Supply Type :AT
Auto Detect DIMM Clk :Enabled
CUP warning Temperature :Disabled
Current System Temperature :35°C/95°F
Current CUP1 Temperature :45°C/113°F
Current CPUFAN1 Speed :5037 RPM
Current CUPFAN2 Speed :
IN0 (V): 2.00V IN1(V) :1.50V
IN2 (V): 3.32V +5V :5.02V
+12 V : 12.28V -12V :-11.95V
-5V : -4.99V VBAT(V) :3.28V
5VSB(V): 5.05V
Shutdown Temperature :Disabled
Figure 5-6: Chipset Features Setup
The parameters in this screen are for system designers, service
personnel, and technically competent users only. Do not reset
these values unless you understand the consequences of your
changes.
Auto Configuration Function:
Auto Configuration selects predetermined optimal values of the
chipset parameters. When disabled, chipset parameters revert
to setup information stored in CMOS. Many fields in this screen
are not available when Auto Configuration is Enabled.
EDO DRAM Speed Selection
The DRAM timing is controlled by the DRAM Timing Registers.
The timings programmed into this register are dependent on the
system design. Slower rates may be required in certain system
designs to support loose layouts or slower memory.