User guide
Table Of Contents
- Contents
- 1-1 About This Manual
- 1-2 System Specifications
- 1-3 Safety Precautions
- 2-1 List of Jumpers and Connectors
- 2-2 Component Locations
- 2-3 How to Set Jumpers
- 2-4 COM Port Connector
- 2-5 RS232/422/485 (COM2) Selection
- 2-6 IRQ12 Release Selection
- 2-7 ATX Power Signal Connector
- 2-8 ATX Power Button
- 2-9 AT/ATX Power Selection
- 2-10 Universal Serial Bus Connector
- 2-11 Solid-State Disk Socket
- 2-12 SSD Memory Map Selection
- 2-13 Keyboard / PS2 Mouse Selection
- 2-14 Keyboard / PS2 Mouse Connector
- 2-15 External Keyboard Connector
- 2-16 Reset Connector
- 2-17 Hard Disk Drive LED Connector
- 2-18 CPU Fan Connector
- 2-19 System Fan Connector
- 2-20 External Speaker Connector
- 2-21 Floppy Disk Drive Connector
- 2-22 Hard Disk Drive Connector
- 2-23 VGA CRT Connector
- 2-24 LCD Panel Connector
- 2-25 LCD VDD Selection
- 2-26 Panel Power Connector
- 2-27 Printer Connector
- 2-28 Power LED & Keylock Connector
- 2-29 LAN Connector
- 2-30 LAN LED Indicators
- 2-31 Green Function Connector
- 2-32. Memory Installation
- 3-1. Introduction
- 3-2. VGA Driver Utility
- 3-3. Flash BIOS Update
- 3-4. LAN Driver Utility
- 3-5. Watchdog Timer Configuration
- 4-1. Power Saving Block Diagram
- 4-2. CPU Doze Mode
- 4-3. System Standby Mode
- 4-4 System Suspend Mode
- 5.1 Introduction
- 5-2 Entering Setup
- 5-3 Standard CMOS Setup Menu
- 5-4 BIOS Features Setup Menu
- 5-5 Chipset Features Setup
- 5-6 Power Management Setup
- 5-7 PnP/PCI Configuration
- 5-8 Load BIOS Defaults
- 5-9 Load Setup Defaults
- 5-10 Integrated Peripherals
- 5-11 Password Setting
- 5-12 IDE HDD Auto Detection
- PC-104 Connector Pin Assignment
- ISA Bus Pin Assignments
- PCI Bus Pin Assignments
- C-1 Introduction
- C-2 Troubleshooting with Error Messages
CommPlete Series 4000 Server SBC, Model IPC-623C 53
Award BIOS Setup
If the controller of the hard-disk drive interface is ESDI, the
selection shall be
“Type 1”.
If the controller of the hard-disk drive interface is SCSI, the
selection shall be “None”
If the controller of the hard-disk drive interface is CD-ROM, the
selection shall be “None”
Type:
Describes the hard drive. Default value is AUTO. Other values:
1-45, user, and none.
CYLS.:
Denotes the number of cylinders in the specified drive type.
HEADS:
Denotes the number of heads in the specified drive type.
PRECOM:
Precom is the read delay circuitry which takes into account the
timing differences between the inner and outer edges of the
surface of the disk platter. The number designates the starting
cylinder of the signal.
LANDZ:
LandZ is the landing zone of the heads. This number
determines the cylinder location where the heads will normally
park when the system is shut down.
SECTORS:
Denotes the number of sectors in the specified drive type.