User guide
Table Of Contents
- Contents
- 1-1 About This Manual
- 1-2 System Specifications
- 1-3 Safety Precautions
- 2-1 List of Jumpers and Connectors
- 2-2 Component Locations
- 2-3 How to Set Jumpers
- 2-4 COM Port Connector
- 2-5 RS232/422/485 (COM2) Selection
- 2-6 IRQ12 Release Selection
- 2-7 ATX Power Signal Connector
- 2-8 ATX Power Button
- 2-9 AT/ATX Power Selection
- 2-10 Universal Serial Bus Connector
- 2-11 Solid-State Disk Socket
- 2-12 SSD Memory Map Selection
- 2-13 Keyboard / PS2 Mouse Selection
- 2-14 Keyboard / PS2 Mouse Connector
- 2-15 External Keyboard Connector
- 2-16 Reset Connector
- 2-17 Hard Disk Drive LED Connector
- 2-18 CPU Fan Connector
- 2-19 System Fan Connector
- 2-20 External Speaker Connector
- 2-21 Floppy Disk Drive Connector
- 2-22 Hard Disk Drive Connector
- 2-23 VGA CRT Connector
- 2-24 LCD Panel Connector
- 2-25 LCD VDD Selection
- 2-26 Panel Power Connector
- 2-27 Printer Connector
- 2-28 Power LED & Keylock Connector
- 2-29 LAN Connector
- 2-30 LAN LED Indicators
- 2-31 Green Function Connector
- 2-32. Memory Installation
- 3-1. Introduction
- 3-2. VGA Driver Utility
- 3-3. Flash BIOS Update
- 3-4. LAN Driver Utility
- 3-5. Watchdog Timer Configuration
- 4-1. Power Saving Block Diagram
- 4-2. CPU Doze Mode
- 4-3. System Standby Mode
- 4-4 System Suspend Mode
- 5.1 Introduction
- 5-2 Entering Setup
- 5-3 Standard CMOS Setup Menu
- 5-4 BIOS Features Setup Menu
- 5-5 Chipset Features Setup
- 5-6 Power Management Setup
- 5-7 PnP/PCI Configuration
- 5-8 Load BIOS Defaults
- 5-9 Load Setup Defaults
- 5-10 Integrated Peripherals
- 5-11 Password Setting
- 5-12 IDE HDD Auto Detection
- PC-104 Connector Pin Assignment
- ISA Bus Pin Assignments
- PCI Bus Pin Assignments
- C-1 Introduction
- C-2 Troubleshooting with Error Messages
Software Configuration
44 CommPlete 4000 Server SBC, Model IPC-623C
2. Install LAN Driver to Windows NT 3.0/4.0
(1) In the Main group of NT, select the “Control Panel” icon.
(2) In the Control Panel window, choose the “Network” icon.
(3) In the Network Settings dialog box, choose the “Add
adapter” button. The Add Network Adapter dialog box
appears.
(4) In the list of network cards, select “<other> Requires disk
from manufacturer”, and then press <Enter> button.
(5) Insert the LAN driver utility, and enter the filename (ex. A:\
pathname) where the setup file OEMSETUP.INF is located,
and then choose OK button.
(6) The screen will appear “Select Line Speed” dialog box,
which is provided by RTL8139.SYS driver. The default
value is “auto” so that the line speed can be auto detected
as 10MB or 100MB, while the RTL8139.SYS is loading.
(7) The screen will appear “Input Ethernet ID” dialog box, which
is provided by RTL8139.SYS driver. This option is only
required when you have more than one RTL8139 PCI Fast
Ethernet adapters on this computer. Select “SKIP” if only
one adapter is installed on this computer.
(8) “Bus Location” displayed in next screen. Your machine
contains more than one hardware bus, please select the
Bus Type and Bus number on which your network adapter
card is installed.
(9) NT will then perform the binding process. If any additional
network software options were installed, you may be
prompted for specific information for these packages.
(10) Re-starting your system you will acquire network service.
Note: For Installing Multiple LAN Adapters:
Enter Windows NT and follow above setup procedure step 2, in
the “Network Settings” dialog box, choose the “Configure...”
button. The “Input Ethernet ID” dialog box appears and input
adapter’s Ethernet ID. Last step to select OK and close
NETWORK SETUP. Select SKIP if only one adapter is
installed on this computer.
For more information on installation procedure, please refer to
TXT directory found on LAN DRIVER UTILITY.