User guide
Table Of Contents
- Contents
- 1-1 About This Manual
- 1-2 System Specifications
- 1-3 Safety Precautions
- 2-1 List of Jumpers and Connectors
- 2-2 Component Locations
- 2-3 How to Set Jumpers
- 2-4 COM Port Connector
- 2-5 RS232/422/485 (COM2) Selection
- 2-6 IRQ12 Release Selection
- 2-7 ATX Power Signal Connector
- 2-8 ATX Power Button
- 2-9 AT/ATX Power Selection
- 2-10 Universal Serial Bus Connector
- 2-11 Solid-State Disk Socket
- 2-12 SSD Memory Map Selection
- 2-13 Keyboard / PS2 Mouse Selection
- 2-14 Keyboard / PS2 Mouse Connector
- 2-15 External Keyboard Connector
- 2-16 Reset Connector
- 2-17 Hard Disk Drive LED Connector
- 2-18 CPU Fan Connector
- 2-19 System Fan Connector
- 2-20 External Speaker Connector
- 2-21 Floppy Disk Drive Connector
- 2-22 Hard Disk Drive Connector
- 2-23 VGA CRT Connector
- 2-24 LCD Panel Connector
- 2-25 LCD VDD Selection
- 2-26 Panel Power Connector
- 2-27 Printer Connector
- 2-28 Power LED & Keylock Connector
- 2-29 LAN Connector
- 2-30 LAN LED Indicators
- 2-31 Green Function Connector
- 2-32. Memory Installation
- 3-1. Introduction
- 3-2. VGA Driver Utility
- 3-3. Flash BIOS Update
- 3-4. LAN Driver Utility
- 3-5. Watchdog Timer Configuration
- 4-1. Power Saving Block Diagram
- 4-2. CPU Doze Mode
- 4-3. System Standby Mode
- 4-4 System Suspend Mode
- 5.1 Introduction
- 5-2 Entering Setup
- 5-3 Standard CMOS Setup Menu
- 5-4 BIOS Features Setup Menu
- 5-5 Chipset Features Setup
- 5-6 Power Management Setup
- 5-7 PnP/PCI Configuration
- 5-8 Load BIOS Defaults
- 5-9 Load Setup Defaults
- 5-10 Integrated Peripherals
- 5-11 Password Setting
- 5-12 IDE HDD Auto Detection
- PC-104 Connector Pin Assignment
- ISA Bus Pin Assignments
- PCI Bus Pin Assignments
- C-1 Introduction
- C-2 Troubleshooting with Error Messages
Software Configuration
38 CommPlete 4000 Server SBC, Model IPC-623C
3-2. VGA Driver Utility
The VGA interface embedded with our IPC-623C can support a
wide range of display mode, such as SVGA, STN, TFT,.....etc.
You can display CRT and LCD Panel simultaneously on this
board, but make sure that the modes for CRT and LCD Panel
are the same. If not, only one of them can be displayed.
VGA CD
1. Awdflash 7.xx program
2. Win 3.1 program
3. Win 95 program
4. Win NT program
5. Win 98 program
6. OS/2 video Device Driver
3-1-2. Installation Procedures of VGA Driver
1. Install VGA Driver to Windows 3.1
(1). To install VGA driver to Windows 3.1, please insert Utility
Disk into floppy disk drive A/B or CD ROM drive under your
Windows 3.1 system, and go to directory where VGA driver
is located.
(2). Click Setup.exe file for VGA driver installation directly.
Follow the instructions on the screen and complete the
installation.
(3). Once installation is completed, you must shut down system
and restart in order for changes to take effect.
2. Install VGA Driver to Windows 95
(1). Click START, SETTINGS, then CONTROL PANEL.
(2). On CONTROL PANEL, click the DISPLAY icon and enter
the SETTINGS tab of the DISPLAY PROPERTIES window.
(3). Select the SETTINGS page, push the CHANGE DISPLAY