User guide
Table Of Contents
- Contents
- 1-1 About This Manual
- 1-2 System Specifications
- 1-3 Safety Precautions
- 2-1 List of Jumpers and Connectors
- 2-2 Component Locations
- 2-3 How to Set Jumpers
- 2-4 COM Port Connector
- 2-5 RS232/422/485 (COM2) Selection
- 2-6 IRQ12 Release Selection
- 2-7 ATX Power Signal Connector
- 2-8 ATX Power Button
- 2-9 AT/ATX Power Selection
- 2-10 Universal Serial Bus Connector
- 2-11 Solid-State Disk Socket
- 2-12 SSD Memory Map Selection
- 2-13 Keyboard / PS2 Mouse Selection
- 2-14 Keyboard / PS2 Mouse Connector
- 2-15 External Keyboard Connector
- 2-16 Reset Connector
- 2-17 Hard Disk Drive LED Connector
- 2-18 CPU Fan Connector
- 2-19 System Fan Connector
- 2-20 External Speaker Connector
- 2-21 Floppy Disk Drive Connector
- 2-22 Hard Disk Drive Connector
- 2-23 VGA CRT Connector
- 2-24 LCD Panel Connector
- 2-25 LCD VDD Selection
- 2-26 Panel Power Connector
- 2-27 Printer Connector
- 2-28 Power LED & Keylock Connector
- 2-29 LAN Connector
- 2-30 LAN LED Indicators
- 2-31 Green Function Connector
- 2-32. Memory Installation
- 3-1. Introduction
- 3-2. VGA Driver Utility
- 3-3. Flash BIOS Update
- 3-4. LAN Driver Utility
- 3-5. Watchdog Timer Configuration
- 4-1. Power Saving Block Diagram
- 4-2. CPU Doze Mode
- 4-3. System Standby Mode
- 4-4 System Suspend Mode
- 5.1 Introduction
- 5-2 Entering Setup
- 5-3 Standard CMOS Setup Menu
- 5-4 BIOS Features Setup Menu
- 5-5 Chipset Features Setup
- 5-6 Power Management Setup
- 5-7 PnP/PCI Configuration
- 5-8 Load BIOS Defaults
- 5-9 Load Setup Defaults
- 5-10 Integrated Peripherals
- 5-11 Password Setting
- 5-12 IDE HDD Auto Detection
- PC-104 Connector Pin Assignment
- ISA Bus Pin Assignments
- PCI Bus Pin Assignments
- C-1 Introduction
- C-2 Troubleshooting with Error Messages
22 CommPlete 4000 Server SBC, Model IPC-623C
Hardware Configuration
2-12 SSD Memory Map Selection
JP7, JP8 : SSD Memory Mapping Selection.
This 32-pin disk-on-chip socket supports an SSD up to 144MB.
This plug-and-play flash ROM SSD can be installed as though it
were a hard disk. If mapped as Drive C, it can be used to boot
up the computer with MS-DOS installed.
JP8
JP7
1
2
7
8
1
2
3
4
JP8
JP7
1
2
7
8
1
2
3
4
JP8
JP7
1
2
7
8
1
2
3
4
JP8
JP7
1
2
7
8
1
2
3
4
JP8
JP7
1
2
7
8
1
2
3
4
JP8
JP7
1
2
7
8
1
2
3
4
SELECTIONS
Jumper Settings
(pins closed)
JP7
JP8
Jumper
Illustration
CC000h-CDFFFh
1-2
3-4
D0000h-D1FFFh
3-4
1-2
D4000h-D5FFFh
3-4
3-4
D8000h-D9FFFh
5-6
1-2
DC000h-DDFFFh
5-6
3-4
E0000h-E1FFFh
7-8
1-2
*** Factory Default CC000h-DCFFFh