User guide
Table Of Contents
- Contents
- 1-1 About This Manual
- 1-2 System Specifications
- 1-3 Safety Precautions
- 2-1 List of Jumpers and Connectors
- 2-2 Component Locations
- 2-3 How to Set Jumpers
- 2-4 COM Port Connector
- 2-5 RS232/422/485 (COM2) Selection
- 2-6 IRQ12 Release Selection
- 2-7 ATX Power Signal Connector
- 2-8 ATX Power Button
- 2-9 AT/ATX Power Selection
- 2-10 Universal Serial Bus Connector
- 2-11 Solid-State Disk Socket
- 2-12 SSD Memory Map Selection
- 2-13 Keyboard / PS2 Mouse Selection
- 2-14 Keyboard / PS2 Mouse Connector
- 2-15 External Keyboard Connector
- 2-16 Reset Connector
- 2-17 Hard Disk Drive LED Connector
- 2-18 CPU Fan Connector
- 2-19 System Fan Connector
- 2-20 External Speaker Connector
- 2-21 Floppy Disk Drive Connector
- 2-22 Hard Disk Drive Connector
- 2-23 VGA CRT Connector
- 2-24 LCD Panel Connector
- 2-25 LCD VDD Selection
- 2-26 Panel Power Connector
- 2-27 Printer Connector
- 2-28 Power LED & Keylock Connector
- 2-29 LAN Connector
- 2-30 LAN LED Indicators
- 2-31 Green Function Connector
- 2-32. Memory Installation
- 3-1. Introduction
- 3-2. VGA Driver Utility
- 3-3. Flash BIOS Update
- 3-4. LAN Driver Utility
- 3-5. Watchdog Timer Configuration
- 4-1. Power Saving Block Diagram
- 4-2. CPU Doze Mode
- 4-3. System Standby Mode
- 4-4 System Suspend Mode
- 5.1 Introduction
- 5-2 Entering Setup
- 5-3 Standard CMOS Setup Menu
- 5-4 BIOS Features Setup Menu
- 5-5 Chipset Features Setup
- 5-6 Power Management Setup
- 5-7 PnP/PCI Configuration
- 5-8 Load BIOS Defaults
- 5-9 Load Setup Defaults
- 5-10 Integrated Peripherals
- 5-11 Password Setting
- 5-12 IDE HDD Auto Detection
- PC-104 Connector Pin Assignment
- ISA Bus Pin Assignments
- PCI Bus Pin Assignments
- C-1 Introduction
- C-2 Troubleshooting with Error Messages
10 CommPlete 4000 Server SBC, Model IPC-623C
Introduction
System Power Requirements :
DC Voltage:+5V; minimum +4.75V, maximum 5.25V.
DC Ampere: 15A.
DC Voltage: +12; minimum +11.4V, maximum +12.6V
DC Ampere: 500mA
Board Dimensions:
338.5mm x 122mm (13.33in. x 4.80in.)
Board Net Weight:
0.4 Kg.
14.1 oz.
1-3 Safety Precautions
Follow the practices below to prevent electrical damage to
personnel and to the computer:
1.Employ standard ESD precautions when working with this
product and its components. Static electricity can damage
semiconductor devices.
2.Take precautions against electric shock. Do not touch any
components of this card when the card is on. Disconnect the
power cord when the system is not in use.
3.Disconnect the power cord when you change any hardware
devices. For instance, when you connect a jumper or install
any cards, a surge of power may damage electronic
components that affect the whole system.