User`s manual

Index
Multi-Tech Systems, Inc. Single Board Computer IAC-F696 User’s Guide (S000349A) 47
LVDSE1 - Panel Connector .........................................25
PKM1 - PS/2 Keyboard & Mouse................................22
SM1 - Sound/Mouse.....................................................24
USBF1/USBF2 - USB Port ..........................................14
VGAA1 - External VGA Connector.............................22
I/O ConnectorPSW1 - ATX Power Button.......................15
Initial Display First...........................................................34
Installing Drivers ..............................................................42
INT Pin 1/2/3/4 Assignment .............................................38
Integrated Peripherals .......................................................34
ECP Mode ....................................................................35
EPP Port Type ..............................................................35
Onboard Parallel Mode ................................................35
Onboard Parallel Port 1 ................................................35
On-Chip Primary PCI IDE ...........................................34
UART 2 Duplex Mode .................................................35
UART 2 Mode Select ...................................................35
Integrated Peripherals AC97 Audio..................................34
Integrated Peripherals FDD Controller .............................35
Integrated Peripherals Initial Display First .......................34
Integrated Peripherals LAN Boot ROM ...........................34
Integrated Peripherals On-Chip Secondary PCI IDE ........34
Integrated Peripherals Serial Ports....................................35
Integrated Peripherals USB Controller .............................34
Integrated Peripherals USB Keyboard Support ................34
Integrated Peripherals USB Mouse Support .....................34
IRQ Resources..................................................................38
J
Jumper Select
KBPW1 - 1x3 Pin 2.45mm...........................................11
SBVB1 - Select Power Mode .......................................11
SLVA1 - Bit Input Mode Select...................................12
Jumper Settings
CMOS1 - Clear CMOS Data..........................................9
PLRS1 - Power LED, HD LED, Reset, Speaker
Connector.................................................................10
SC2T1/SC2T2 – Select COM2 Type .............................8
SCF1 - Master/slave Select ..........................................10
VLCD1 - Select Panel Voltage.......................................9
Jumper Settings Summary ..................................................8
L
LAN Boot ROM ...............................................................34
Load Optimized Defaults..................................................39
M
Memory ............................................................................32
Mouse Control ..................................................................31
N
NumLock Status ...............................................................31
O
Onboard Parallel Mode.....................................................35
Onboard Parallel Port 1.....................................................35
On-Chip Primary PCI IDE................................................34
On-Chip Secondary PCI IDE............................................34
Ordering Replacement Parts ........................................45
Other Boot Device ............................................................30
P
P2C/C2P Concurrency ..................................................... 32
Panel Type........................................................................ 33
PC Health Status .............................................................. 39
PCI Delay Transaction ..................................................... 33
PCI Dynamic Bursting ..................................................... 33
PCI Maser 0 WS Write..................................................... 33
PCI#2 Access ................................................................... 33
PCI/VGA Palette Snoop................................................... 38
PnP OS Installed .............................................................. 37
PnP/PCI Configuration
Assign IRQ for USB .................................................... 38
Assign IRQ for VGA ................................................... 38
DMA Resource ............................................................ 38
INT Pin 1/2/3/4 Assignment ........................................ 38
IRQ Resources ............................................................. 38
PCI/VGA Palette Snoop .............................................. 38
PnP OS Installed .......................................................... 37
Reset Configuration Data............................................. 37
Resource Controlled by ............................................... 37
PnP/PCI Configuration Setup........................................... 37
Power Management Setup................................................ 36
ACPI Function ............................................................. 36
Power on by Lan.......................................................... 36
Power On by RTC Alarm ............................................ 36
Power ON/OFF Status after AC Power Loss ............... 36
Soft-Off State............................................................... 36
Video Off In Suspend .................................................. 36
Video Off Method........................................................ 36
Power on by Lan .............................................................. 36
Power On by RTC Alarm................................................. 36
Power On Self Test .......................................................... 30
Power ON/OFF Status after AC Power Loss ................... 36
Primary Master/Primary Slave ......................................... 28
PS/2 Mouse Control ......................................................... 31
R
Replacement Parts........................................................ 45
Reset Configuration Data ................................................. 37
Resource Controlled by.................................................... 37
S
Save & Exit Setup ............................................................ 40
SDRAM Cycle Length ..................................................... 32
Security Option ................................................................ 31
Select Display .................................................................. 33
Serial Ports ....................................................................... 35
Set Date............................................................................ 28
Set Supervisor/User Password.......................................... 40
Set Time ........................................................................... 28
SMART Capability .......................................................... 31
Soft-Off State ................................................................... 36
Standard CMOS Setup Screen ......................................... 28
Swap Floppy Drive .......................................................... 30
System BIOS Cacheable .................................................. 33
T
Technical Specifications .................................................... 5
U
UART 2 Duplex Mode..................................................... 35