Leica RX1200 User Manual Version 6.
RX1200 Introduction 2 Introduction Purchase Congratulations on the purchase of an RX1200. This manual contains important safety directions as well as instructions for setting up the product and operating it. Refer to "7 Safety Directions" for further information. Read carefully through the User Manual before you switch on the product. Product identification The type and serial number of your product are indicated on the type plate.
Symbols The symbols used in this manual have the following meanings: Type Description Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Danger Warning Indicates a potentially hazardous situation or an unintended use which, if not avoided, could result in death or serious injury.
RX1200 Introduction Validity of this manual Available documentation 4 This manual applies to all RX controllers. Differences between the various models are marked and described. Name Description/Format of RX1200 manuals User Manual All instructions required in order to operate the product to a basic level are contained in the User Manual. Provides an overview of the product together with technical data and safety directions.
Refer to the following resources for all System1200 documentation/software: • the SmartWorx DVD • Introduction http://www.leica-geosystems.
RX1200 Table of Contents 6 Table of Contents In this manual Chapter 1 Description of the System 12 1.1 1.2 12 15 15 19 21 22 24 1.3 1.4 2 Page Terminology System Concept 1.2.1 Software Concept 1.2.2 Data Storage and Data Conversion Concept 1.2.3 Power Concept Container Contents RX Components User Interface 26 2.1 2.2 2.3 2.
3 Setting up the Equipment 38 3.1 38 38 43 44 46 47 49 51 52 54 54 56 58 60 62 66 68 70 81 3.2 3.3 3.4 3.5 3.6 3.7 Table of Contents Equipment Setup 3.1.1 Fixing the RX to a Holder and Pole 3.1.2 Fixing the RX to a Handstrap 3.1.3 Fixing the RX to a GNSS Receiver 3.1.4 Setting up for Remote Control (with the RadioHandle) 3.1.5 Setting up for Remote Control (with the TCPS27) 3.1.6 Setting up SmartPole 3.1.7 Setting up a Real-Time Reference 3.1.8 Setting up SmartRover Batteries 3.2.
RX1200 Table of Contents 4 Getting Started with SmartWorx 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 Overview Turning on the RX, setting the Instrument Mode and Interface Understanding the Main Menu Switching Between GPS and TPS Working with Licence Keys Connecting to a Digital Cellular Phone Connecting to the Disto Connecting to a Personal Computer Connecting to a Radio (for Remote Control Surveys) 4.9.1 Available Radios 4.9.2 Working in Remote Mode 4.9.3 Working in Transparent Mode 4.9.
5 Local Mode 114 5.1 5.2 5.3 5.4 5.5 114 115 116 117 121 121 126 128 5.6 6 Table of Contents Accessing the Main Configuration Menu Overview of the Main Configuration Menu Choosing a Sensor Local Settings Radio Settings 5.5.1 Radio Communication Settings 5.5.2 Configuring the Radios Working with a Sensor Care and Transport 130 6.1 6.2 6.
RX1200 Table of Contents 7 8 10 Safety Directions 134 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 134 135 137 138 140 143 149 152 General Introduction Intended Use Limits of Use Responsibilities End User Licence Agreement EULA Hazards of Use Electromagnetic Compatibility EMC FCC Statement, Applicable in U.S.
9 Technical Data 168 9.1 9.2 RX Technical Data SmartAntenna Technical Data 9.2.1 Tracking Characteristics 9.2.2 Accuracy 9.2.3 Technical Data GHT56 Technical Data Conformity to National Regulations 9.4.1 RX1210 9.4.2 RX1250, GFU23 9.4.3 GFU24, Siemens MC75 9.4.4 GFU19 (US), GFU25 (CAN), GFU26 (US) CDMA MultiTech MTMMC-C 9.4.
RX1200 Description of the System 1 1.
RX1210 Recommended for ...
RX1200 Description of the System RX available radios 14 Radios for remote control (RCS) are found in the following devices: Radio Modem Description GFU23 Clip-on-Housing with an integrated radio modem and attached radio antenna. RadioHandle Instrument carry handle with an integrated radio modem and attached radio antenna. RX1250T Controller with an integrated radio modem and attached radio antenna. This controller has a monochrome display.
1.2 System Concept 1.2.1 Software Concept Software for RX1210/RX1210T Software type Description RX firmware (RX1200.fw) These RX models are used as terminals and only one software is required to be installed. All other necessary software is loaded onto the GPS/TPS. This software includes all the local display, sound and communication settings. These settings can only be changed by putting the RX into local mode. Software for all RX1250 models Software type Description RX firmware (RX1250_xx.
Description of the System Software type RX1200 16 Description - The programs Survey and Wake-Up (for GPS) and Survey and Setup (for TPS), which cannot be deleted. - The English language, which cannot be deleted. Language software (SYS_LANG.sxx) Numerous languages are available for the RX. Language software is also referred to as system language. The system software enables a maximum of three languages which can be stored at any one time - the English language and two other languages.
Software type Description Customised application programs Custom software specific to user requirements can be developed using the GeoC++ development kit. Information on the GeoC++ development environment is available on request from a Leica Geosystems representative. Software for the SmartAntenna Software type Description SmartAntenna software This is the software for the ATX1230 GG. It covers the firmware for the measurement engine.
Description of the System Software for RX1200 18 Description If GPS1200 is being used, refer to the GPS1200 Technical Reference Manual. If LGO is being used, refer to the online help in LGO. All RX1250 models All software is stored in the System RAM of the RX. The software can be uploaded onto a CompactFlash card in the RX. After uploading, the software must then be transferred from the CompactFlash card to the RX System RAM.
1.2.2 Data Storage and Data Conversion Concept Description Data is stored within a job in a database on a memory device. The memory device can be a CompactFlash card or internal memory. Memory device CompactFlash card: A CompactFlash card slot is standard. A CompactFlash card can be inserted and removed. Available capacity: 256 MB.
Description of the System Data conversion RX1200 20 Export Data can be exported from a job in a wide range of ASCII formats. The export format is defined in Format Manager which is a PC tool in LEICA Geo Office. Refer to the online help of LGO for information on creating format files. Data can also be exported from a job in DXF or LandXML format. Import Data can be imported from ASCII, DXF, GSI8 or GSI16 format. Transfer data Data can be transferred in various ways.
1.2.3 Power Concept General Power options Use the Leica Geosystems batteries, chargers and accessories or accessories recommended by Leica Geosystems to ensure the correct functionality of the instrument. Model RX1210/RX1210T Power supply Via cable, or Via clip-on connector of the GPS receiver, or Externally via cable all RX1250 models Internally via GEB211 battery, or Externally via cable If an external power supply is connected and one internal battery is inserted, then the external power is used.
RX1200 Description of the System 1.
Container for System 1200 components part 2 of 2 a b c SYS12_002 Description of the System d h e i j k f l RX1200 g a) b) c) d) e) f) g) h) i) j) k) l) Manuals GHT57 Bracket CompactFlash card GRZ4 / GRZ122 Prism Spare stylus Software DVD GEB211 Batteries GHT56 Holder TNC L-adapter GEB221 Battery RX Controller GHT39 Holding plate 23
Description of the System 1.
Underside of RX a b c d a) b) c) d) e) f) Bottom spring clip for pole holder Top clips for pole holder Hand strap top clips Stylus Hand strap bottom clips LEMO port For RX1250 including USB port g) Battery compartment For RX1250 with CompactFlash card compartment h) Clip-on-contacts e f For RX1250, a Bluetooth port is included inside to facilitate connectivity to the SmartAntenna, digital cellular phone or Leica DistoTM.
RX1200 User Interface 2 2.1 26 User Interface Keyboard Keyboard display ESC j PROG OFF F1 Q W A F2 E S Z F C F8 F4 T D X F7 F3 R G V F5 Y U H B SPACE F9 F6 I J N F10 K L CAPS M F11 SHIFT 7 8 4 1 6 2 0 PgUp 9 5 PgDn 3 .
) Keys For the purpose of the illustration, a RX1250 model has been selected which is representative for all models. Differences to other RX models are outlined. Key Function Function keys F1-F6 Correspond to six softkeys that appear on the bottom of the screen when the screen is activated. Hot keys F7-F12 User definable keys to execute chosen commands or access chosen screens. Alpha keys To type letters. Numeric keys To type numbers. CAPS Switches between upper case and lower case letters.
RX1200 User Interface Key Function PROG (ON) If RX is already off: Turns RX on. 28 If RX is already on: Accesses the Programs menu. SHIFT Switches between the first and second level of function keys. SPACE Enters a blank. USER In SmartWorx mode: Calls the user defined menu. In Terminal mode: Hold down for 2 s to open the Main Configuration Menu. Arrow keys Move the focus on the screen. ENTER Selects the highlighted line and leads to the next logical menu / dialog.
Key combinations Key Function PROG plus USER In SmartWorx mode and in the Main Menu: Turns RX off when pressed simultaneously. In Terminal mode: Turns RX off when pressed simultaneously. SHIFT SHIFT SHIFT PROG ( USER STAT (F3) User Interface Pages up. Pages down. ) For all RX1250 models: Displays the Windows desktop, task bar and start menu. Opens the Status Menu.
RX1200 User Interface 2.2 30 Screen Screen f a b c g d h i j e k S_RX12_001 Elements a) b) c) d) e) f) g) h) i) j) k) Time Caption Title Screen area Message line Icons ESC CAPS SHIFT icon Quick coding icon Softkeys Type Description Time The current local time is shown. Caption Shows location either in Main Menu, under PROG key or USER key. Title Name of the screen is shown.
Type Description Screen area The working area of the screen. Message line Messages are shown for 10 s. Icons Shows current status information of the instrument. Can be used with touch screen to access the subsequent screen. ESC Can be used with touch screen. Same functionality as the ESC fixed key. The last operation will be undone. CAPS The caps mode for upper case letters is active.The caps mode is activated and deactivated by pressing UPPER (F5) or LOWER (F5) in some screens.
RX1200 User Interface 2.3 32 Operating Principles Keyboard and touch screen The user interface is operated either by the keyboard or by the touch screen with supplied stylus. The workflow is the same for keyboard and touch screen entry, the only difference lies in the way information is selected and entered. Operation by keyboard Information is selected and entered using the keys. Refer to "2.1 Keyboard" for a detailed description of the keys on the keyboard and their function.
2.4 Icons Description Battery icons For a complete listing of icons • for GPS1200 refer to GPS1200 System Field Manual. • for TPS1200+ refer to TPS1200+ System Field Manual. • for TPS1200 refer to TPS1200 System Field Manual. The power status (indicated by six levels) and source of the battery is displayed. Tapping the icon leads to STATUS Battery & Memory, Battery.
RX1200 User Interface Icon 34 Description For TPS1200+/TPS1200 instruments: External TPS and RX battery are in use Bluetooth icons The status of each Bluetooth port and any Bluetooth connection is displayed. Tapping the icon leads to STATUS Bluetooth. Icon Description All RX1250 models are integrated with Bluetooth A Bluetooth connection is established and active Bluetooth connection not established. Bluetooth port 1,2,3 are down Bluetooth connection established.
Full Switch icon in GPS instrument mode The following icon appears only in the Main Menu. Icon Description Tapping the icon leads to Instrument Mode Selection, which allows a full switch from GPS instrument mode to TPS instrument mode. Refer to "4.4 Switching Between GPS and TPS" for further details. Full Switch icon in TPS instrument mode The following icon appears only in the Main Menu.
RX1200 User Interface Icon 36 Description No connection to the SmartAntenna Active connection to the SmartAntenna - navigated solution Active connection to the SmartAntenna - code solution Active connection to the SmartAntenna - fixed solution Tapping the icon leads to TPS Survey.
Icon Description Active connection to the instrument - Locked onto prism Interface icons in TPS instrument mode Tapping the icon leads to Configure Interfaces.
RX1200 Setting up the Equipment 3 38 Setting up the Equipment 3.1 Equipment Setup 3.1.1 Fixing the RX to a Holder and Pole Components of the GHT39 holder The GHT39 holder consists of a number of components, as shown in the diagram.
Components of the GHT56 holder The GHT56 holder consists of a number of components, as shown in the diagram. d GHT52 clamp e a) Plastic sleeve f g b) Pole clamp a c) Clamp bolt b h GHT56 holder c RX12_016 Fixing the RX and GHT39 holder to a pole step-by-step k j i d) Tightening screw e) Mounting arm f) Clip-on-contacts for connecting RX1250 g) LED h) Mounting plate i) Battery compartment j) Locking mechanism for battery k) Space for clip-on-housing with LEMO port Description 1.
RX1200 Setting up the Equipment 40 Description 3. Insert pole into the clamp hole. 4. Adjust the angle of the mounting plate and the height of the holder on the pole to comfort. 5. Tighten the clamp with the tightening screw. ) ) Once tightened, the button on the tightening screw can be depressed to change the position of the handle for more comfort. A locking mechanism is incorporated in the mounting plate of the holder. 6.
Description 8. Apply slight pressure in a downward direction and then lower the top part of RX until the unit is clicked into the holder. The guides of the holder aid in this action. RX12_006 9. After RX is placed onto the mounting plate ensure that the locking pin is put into the locked position. To lock the locking pin, push up the red button from below.
RX1200 Setting up the Equipment Detaching the RX from a pole stepby-step 42 Description 1. Unlock the locking pin by pushing down the red button situated on top of the mounting plate. 2. Place the palm over the top of RX until the fingers grip the bar of the holder under the top of RX. 3. Compress the top of RX toward the bar of the holder. 4. While in this position, raise the top of RX where the palm is gripping the unit up from the holder.
3.1.2 Fixing the RX to a Handstrap Fixing the RX to a Handstrap step-bystep Description 1. Hold the main hook rotated to approximately the 11 o'clock position in relation to RX. 2. Lower the main hook onto the pivot knob in the middle of RX. 1 3. Rotate the main hook to the 12 o'clock position. A click should be felt when the clip is secure. 2 4. Take the other end of the handstrap and clip 3 it to the base of RX.
RX1200 Setting up the Equipment 3.1.3 44 Fixing the RX to a GNSS Receiver Fixing the RX to GNSS receiver step-by-step Description 1. Hold RX above the recess in the housing of the GNSS receiver intended for the unit. 2 2. Lower the bottom part of RX into the recess in the housing of the GNSS receiver. 3. Apply slight pressure in a downward direction and then lower the top part of RX until the unit is clicked into the GNSS receiver. The recess in the housing of the GNSS receiver helps to guide RX.
Detaching the RX from GNSS receiver step-bystep Description 1. Place the palm over the top of RX. 2. Compress RX downward toward the ports of the GNSS receiver. 3. While in this position, raise the top of RX from the GNSS receiver.
RX1200 Setting up the Equipment 3.1.4 46 Setting up for Remote Control (with the RadioHandle) TPS1200+/TPS1200 /RX1200 setup for RCS with RadioHandle e a f g b h c d RX12_041 a) b) c) d) e) f) g) h) 360° prism Prism pole RX1250T/RX1250Tc RX holder and pole clamp RH1200 RadioHandle Communication side cover TPS1200+/TPS1200 instrument Tripod Refer to TPS1200+/TPS1200 User Manual for further details on the RadioHandle.
3.1.
RX1200 Setting up the Equipment Description 1. The GHT43 tripod adapter is used to mount TCPS27B to all Leica standard tripods, in order to optimise the radio transmission performance. Attach TCPS27B to the adapter and then attach to the tripod leg. 2. Adjust the angle of TCPS27B until it is approximately vertical. 3. Adjust the location of the adapter on the tripod leg so that there are no metallic objects in the horizontal plane around the antenna.
3.1.
Setting up the Equipment 50 The GLS12 (cm)/GLS12F (ft) telescopic pole has fixed equally spaced snap-lock positions. The scale readings along the pole relate to the height of the reflector (prism centre). Two additional positions, clearly marked with diagrams on the pole, relate to the SmartAntenna. The snap-lock must always click into position. Snap-lock positions Diagram on pole 2. Use only this snap-lock position for measurements with: SmartAntenna and the GRZ122 360° prism Antenna Height (MRP) = 2.
3.1.7 Setting up a Real-Time Reference Description Two setups for RX1250 are given as example. Refer to GPS1200 Technical Reference Manual for information on additional setups.
Setting up the Equipment 3.1.
Increase radio coverage on SmartRover Description Some applications require the maximum radio coverage. In those cases the radio antenna is mounted on an antenna arm which is fixed to the pole just below the SmartAntenna. Connection is made between the radio housing and the radio antenna. Connect radio antenna and radio housing using cable step-by-step Description 1. Clip the antenna arm to the SmartAntenna. 2. Screw the radio antenna onto the antenna arm. 3. Attach the radio in its housing to GHT56. 4.
Setting up the Equipment 3.2 Batteries 3.2.1 Operating Principles ) ) RX1200 54 This chapter is valid for all RX1250 models and GHT56. Primary use/charging • The battery must be charged prior to using it for the first time because it is delivered with an energy content as low as possible. • For new batteries or batteries that have been stored for a long time (> three months), it is effectual to make only one charge/discharge cycle.
Operation/Discharging • The batteries can be operated from -20°C to +55°C/-4°F to +131°F. • Low operating temperatures reduce the capacity that can be drawn; very high operating temperatures reduce the service life of the battery.
RX1200 Setting up the Equipment 3.2.2 56 Battery for all RX1250 models Change battery step-by-step 2 4 5 3 6 RX12_018 f Description 1. Turn RX over to gain access to the battery compartment. 2. Push the slide fastener in the direction of the arrow with the open-lock symbol. 3. Open the battery compartment.
Description 4. Pull the battery from the battery compartment. 5. A pictogram of the battery is displayed inside the battery compartment. This is a visual aid to assist in placing the battery correctly. 6. Place the battery into the battery compartment with the Leica logo facing to the left. 7. Close the battery compartment by pushing the slide fastener in the direction of the arrow with the close-lock symbol.
RX1200 Setting up the Equipment 3.2.3 58 Battery for SmartAntenna Change battery step-by-step 1 2 3 4 TPS12_193 Description 1. ) Turn SmartAntenna over to gain access to the battery compartment. Open the battery compartment by pushing the slide fastener in the direction of the arrow with the open-lock symbol. 2. Pull out the battery housing. The battery is attached to the housing. 3. Hold the battery housing and pull the battery from the battery housing.
Description 4. A polarity of the battery is displayed inside the battery housing. This is a visual aid to assist in placing the battery correctly. 5. Place the battery onto the battery housing, ensuring that the contacts are facing outward. Click the battery into position. 6. Close the battery compartment by pushing the slide fastener in the direction of the arrow with the close-lock symbol.
RX1200 Setting up the Equipment 3.2.4 60 Battery for GHT56 Change battery step-by-step 3 2 5 6 6 2 RX12_022 f Description 1. Turn GHT56 over to gain access to the battery compartment. 2. Press simultaneously on the right side of the locking mechanism and the left side of the battery. ) This unlocks the battery from its locked position. 3. Pull the battery from the battery compartment. 4. Place the battery into the battery compartment.
Description 5. Press simultaneously on the right side of the locking mechanism and the right side of the battery. ) ) This locks the battery into position. GEB211 and GEB221 can both be used with GHT56. The battery powers a device in a clip-on-housing attached to the GHT56.
Setting up the Equipment 3.3 ) ) ) RX1200 Working with the CompactFlash Card This chapter is only valid for all RX1250 models. • Keep the card dry. • Use it only within the specified temperature range. • Do not bend the card. • Protect the card from direct impacts. Failure to follow these instructions could result in data loss and/or permanent damage to the card.
Insert and remove a CompactFlash card step-by-step 2 4 3 11 10 RX12_019 Description 1. The CompactFlash card is inserted into a slot inside the battery compartment. Turn RX over to gain access to the battery compartment. 2. Push the slide fastener in the direction of the arrow with the open-lock symbol. 3. Open the battery compartment.
RX1200 Setting up the Equipment Description 4. Pull the battery from the battery compartment. 5. ) The card should be held with the label for the care instructions upwards and the contacts facing the slot. Slide the card firmly into the slot until it clicks into position. 6. Place the battery into the battery compartment. 7. Close the compartment cover. 8. To remove the card, open the cover of the battery compartment. 9. Pull the battery from the battery compartment. 10.
Description 1. Select Main Menu: Tools...\Format Memory Device. 2. TOOLS Format Memory Device Select the memory device to be formatted. ) ) By activating the format command all data will be lost. Make sure that all important data on the CompactFlash card has been backed up before formatting the card. Before formatting the internal memory make sure that all important data is first transferred to the PC.
RX1200 Setting up the Equipment 3.4 66 LED Indicators on SmartAntenna LED indicators Description SmartAntenna has Light Emitting Diode indicators. They indicate the basic antenna status.
Description of the LED’s IF the TRK BT PWR Setting up the Equipment is THEN off no satellites are tracked. flashing green less than four satellites are tracked, a position is not yet available. green enough satellites are tracked to compute a position. red SmartAntenna is initialising. green Bluetooth is in data mode and ready for connecting. purple Bluetooth is connecting. blue Bluetooth has connected. flashing blue data is being transferred off power is off. green power is okay.
RX1200 Setting up the Equipment 3.5 68 LED Indicators on GHT56 LED indicator Description GHT56 has one Light Emitting Diode indicator. It indicates the basic power status.
Description of the LED IF the is THEN PWR off power is off. Setting up the Equipment green power is okay. flashing green power is low. The remaining time for which enough power is available depends on the type of survey, the temperature and the age of the battery. red power is very low. The battery should be changed.
Setting up the Equipment 3.
Attach a clip-onhousing step-bystep The clip-on-housing for devices fits to the underside of the GHT56. RX12_020 Description 1. Setting up the Equipment ) A circular screw is located at one end of the clip-on-housing. Ensure that the circular screw is in the unlocked position. Turn it anticlockwise, as shown by the lock and arrow symbols on the screw.
RX1200 Setting up the Equipment 72 Description Turn GHT56 over to gain access to the space for the clip-on-housing. 2. Place the clip-on-housing into position such that • the guide rails on the GHT56 are aligned with the guide rails on the clipon-housing. AND • the LEMO port on the GHT56 is aligned with the connector on the clip-onhousing. 3. Slide the clip-on-housing into position such that the connector is completely plugged into the LEMO port. It clicks.
Description 3. Pull the clip-on-housing from the GHT56. Insert a SIM card step-by-step For those digital cellular phones that require SIM cards. Description 1. Take the SIM card, a coin and a pen. 2. Locate the SIM card screw, that covers the SIM card slot, on the bottom of the clip-on-housing. 3. Insert the coin into the groove of the SIM card screw. 4. Turn the coin anticlockwise to loosen the SIM card screw. 5. Remove the SIM card screw from the housing. 6.
RX1200 Setting up the Equipment Description 10. Place the SIM card screw back on the housing. 11. Insert the coin into the groove of the SIM card screw. 12. Turn the coin clockwise to tighten the SIM card screw.
Remove a SIM card step-by-step For those digital cellular phones that require SIM cards. 7 6 5 4 GPS12_088 Description 1. Take a coin and a pen. 2. Locate the SIM card screw, that covers the SIM card slot, on the bottom of the clip-on-housing. 3. Insert the coin into the groove of the SIM card screw.
RX1200 Setting up the Equipment 76 Description 4. Turn the coin anticlockwise to loosen the SIM card screw. 5. Remove the SIM card screw from the housing. 6. Using the pen, press the small button of the SIM card slot to eject the SIM card holder. 7. Take the SIM card holder out off the SIM card slot. 8. Take the SIM card out of the SIM card holder. 9. Put the SIM card holder back into the SIM card slot, the even side not facing the contacts inside the slot. 10.
LED indicators Description Each clip-on-housing for a radio, digital cellular phones or Bluetooth communication has Light Emitting Diode indicators on the bottom side. They indicate the basic device status.
RX1200 Setting up the Equipment 78 Description of the LED’s IF the on is THEN Config LED GFU14 with Satelline 3AS, GFU23 red the device is in the configuration mode controlled from the PC via cable. Data transfer LED any device off data is not being transferred. green or flashing green data is being transferred. Signal strength LED red GFU19 (US), GFU25 (CAN), GFU26 (US) flashing red with CDMA MultiTech off MTMMC-C GFU23 device is on, not registered on the network.
IF the on is THEN GFU24 with red call is in progress. Siemens MC75 red: long flash, long no SIM card inserted, no PIN break entered or network search, user authentication or network login in progress. GFU15 with Pacific Crest PDL Setting up the Equipment red: short flash, long break logged onto network, no call in progress. red: flashing red, long break GPRS PDP context activated. red: long flash, short break Packet switched data transfer is in progress. off device is off.
RX1200 Setting up the Equipment IF the Power LED 80 on is THEN GFU14 with Satelline 3AS red or flashing red the communication link, Data Carrier Detection, is okay on the roving receiver. off the DCD is not okay. any device off power is off. green power is okay.
3.7 Guidelines for Correct Results with GNSS Surveys Undisturbed satellite signal reception Successful GNSS surveys require undisturbed satellite signal reception, especially at the receiver which serves as a reference. Set up the receivers in locations which are free of obstructions such as trees, buildings or mountains. Steady antenna for static surveys For static surveys, the antenna must be kept perfectly steady throughout the whole occupation of a point. Put the antenna on a tripod or pillar.
Getting Started with SmartWorx 4 4.
4.2 Turning on the RX, setting the Instrument Mode and Interface Turning the RX on step-by-step Description 1. Ensure that the RX has a power supply. Press PROG (ON) on the keyboard. For RX1210/RX1210T, the RX will automatically turn on if it is connected via cable or via clip-on connector to GPS/TPS which is already on. 2. For all RX1250 models, the Windows desktop is the default display after starting up. To use the RX as a terminal: Double click on the Terminal icon.
Getting Started with SmartWorx RX1200 Description 3. For SmartWorx, the Instrument Mode Selection screen is displayed by default. To connect the RX to GPS, select Choose Sensor=GPS. To show this screen the next time the RX is turned on, select Show at Startup=Yes. For SmartWorx, the Instrument Mode Selection screen is displayed by default. To connect the RX to TPS, select Choose Sensor=TPS. To show this screen the next time the RX is turned on, select Show at Startup=Yes. 4. Configuring the interface.
Description Setting the SmartAntenna Interface. Turn on the SmartAntenna. Set Use Device=Yes. Select a free Bluetooth port. Press DEVCE (F5) to open a list of devices. Select the SmartAntenna. Press SRCH (F4) to search and establish a data connection to the SmartAntenna. Setting the Instrument Interface. For RX1250T/RX1250Tc: Set the instrument interface to: Port=Internal Radio, Device=Int. Radio. For TPS with RadioHandle: Set the GeoCom interface to: Port=Port 2(Handle), Device=RH1200. 5.
Getting Started with SmartWorx ) Turning the RX off RX1200 86 Setting the interface between the RX and the connecting device can always be set later. From the Main Menu select Config/ Interfaces. Option Description Turning the RX off The RX can only be turned off in the Main Menu screen or in the Windows CE desktop. Press USER and PROG simultaneously, or Press and hold ESC for 2 s.
4.3 Understanding the Main Menu The Main Menu Description 1. By default, the Main Menu is the first screen shown after starting up from the Windows desktop. To set another screen for the start up: Select Config from the Main Menu, Select General Settings, Select Start Up, Select the Start Up page, 2. Select a start screen from the choicelist, Press CONT (F1) to go to the Main Menu. Main Menu icons Refer to "2.4 Icons" for a list and description of all available icons in the Main Menu.
Getting Started with SmartWorx Main Menu keys RX1200 88 Description To select the highlighted menu function and continue CONT (F1) To select another sensor - switching between GPS and TPS SHIFT MODE (F2) To put the RX into sleep mode. In sleep mode, the RX shuts SHIFT SLEEP (F3) down and reduces power. The sleep mode is designed to preserve energy. Rebooting the RX from sleep mode is quicker than a cold start after turning off.
4.4 Switching Between GPS and TPS Full switching step-by-step To switch from GPS instrument mode to TPS instrument mode: 1. Option 1: Click on the TPS icon , or Option 2: Press SHIFT MODE (F2). 2. Select Choose Sensor=TPS. Press CONT (F1) to go to the TPS1200+/TPS1200 Main Menu. To switch from TPS instrument mode to GPS instrument mode: 1. Option 1: Click on the GPS icon , or Option 2: Press SHIFT MODE (F2). 2. Select Choose Sensor=GPS. Press CONT (F1) to go to the GPS1200 Main Menu.
Getting Started with SmartWorx Switching in survey step-bystep RX1200 To switch between TPS Survey and GPS Survey during Survey: 1. From TPS Survey: Option 1: Click on the GPS icon, or Option 2: Configure and assign a hot key: Select Config from the Main Menu, Select General Settings, Select Hot Keys & User Menu 2. From GPS Survey: Option 1: Click on the TPS icon, or Option 2: Press the configured hot key.
Switching in setup step-by-step To switch to GPS Survey during Setup: 1. Select the setup method. 2. Press GPS (F4) to access GPS Survey. 3. The measured GPS point is stored to the Fixpoint Job. This point can be used as a control point in TPS Setup. The display masks are user configured. Switching in Setup (for SmartPole) is available only in TPS mode.
Getting Started with SmartWorx 4.5 RX1200 92 Working with Licence Keys Remote Licensing It is possible to temporarily transfer a program licence from TPS1200+/TPS1200 onto any of the RX1250 models. This procedure would only make sense when the RX is to be used as a data logger. Available programs RX1210/RX1210T For these models, only the RX firmware file is loaded. All programs are loaded onto the GPS/TPS. Refer to "1.2.1 Software Concept" for further details.
Available programs Licence Key DXF Import Hidden Point (for TPS only) 9 RoadRunner 9 Reference Line 9 Reference Plane 9 Stakeout Protected options Volume Calculations 9 Sets of Angles (for TPS only) 9 Survey Cross Section 9 Traverse (for TPS only) 9 Protected option Licence Key licence - SmartPole 9 licence - GPS Survey Functionality 9 option - Cogo (Area Division) 9 option - Extended OWI messages 9 Getting Started with SmartWorx RX1200 93
Getting Started with SmartWorx RX1200 Protected option option - GLONASS permanent option Activating a licence Description 1. To enter a licence key or upload a licence key file: Select Tools from the Main Menu, Select Licence Keys from the Tools Menu.
Description 2. Upload Key File: Upload the key file from the CompactFlash card. The key file must be stored in the \SYSTEM directory on the CompactFlash card. Licence key files use the naming convention L_123456.key, where 123456 is the instrument serial number. 3. Manual Entry of Key: Type the key in manually. 4. An optional step is to delete all licence keys. Press SHIFT DEL (F4). 5. Press CONT (F1) to go to the Main Menu.
RX1200 Getting Started with SmartWorx 4.6 96 Connecting to a Digital Cellular Phone Connecting step-by-step Description 1. Select Main Menu: Config...\Interfaces... in the Leica software. 2. Highlight Real-Time. 3. EDIT (F3) 4. CONFIGURE Real-Time Mode Select a free Bluetooth port. 5. DEVCE (F5) 6. CONFIGURE Devices, Modems/GSM page Highlight a Bluetooth capable digital cellular phone. 7. CONT (F1) 8. SRCH (F4) to search for the digital cellular phone.
Description All available Bluetooth devices are displayed. 10. Highlight the digital cellular phone to be used. 11. CONT (F1) ) ) ) Getting Started with SmartWorx If the digital cellular phone selected is connected for the first time, the Windows CE dialog for pairing comes up. Type in 0000 as identification number for Leica’s Bluetooth and click OK. Some digital cellular phones also ask for the identification number for Leica’s Bluetooth. The number is 0000.
Getting Started with SmartWorx 4.7 RX1200 Connecting to the Disto Connecting step-by-step Description 1. Turn on the Disto. Press the Bluetooth key to activate Bluetooth. The Bluetooth icon will display on the Disto screen and will continue to blink until there is a successful data connection to the RX. Bluetooth will switch off on the Disto if the connection is not established within 240 sec. 2. Ensure that the RX is in GPS mode. Go to the Survey program and to the Survey Begin screen.
Description 3. Press SHIFT CONF (F2) to enter the Configuration screen. 4. Set
Getting Started with SmartWorx RX1200 Description 5. Measure the required distance with the Disto. For Disto A4/A5, press and activate the 2nd key. Then press the Bluetooth key to send the measurement to the RX. For Disto A6 it is sufficient to press the Bluetooth key. The distance will be sent and displayed on the RX screen.
4.8 Connecting to a Personal Computer ActiveSync Connect USB cable to PC for the first time step-by-step Microsoft ActiveSync is the synchronization software for Windows mobile-based pocket PC’s. ActiveSync enables a PC and a Windows mobile-based pocket PC, like the RX1250, to communicate. ActiveSync is freeware. It can be downloaded from the Microsoft website. Description 1. Start the PC. 2. Have the SmartWorx DVD version 5.0 or higher ready. 3. Plug the GEV161 cable into RX1250. 4. Turn the RX1250 on.
Getting Started with SmartWorx RX1200 102 Description 10. Next>. 11. Insert the SmartWorx DVD version 5.0 or higher. 12. Tick Search removable media (floppy, CD-ROM...). 13. Next>. 14. Confirm Hardware Installation window with Continue Anyway. 15. Finish. 16. Run the ActiveSync installation program if not already installed. 17. Allow USB connections inside the Connection Settings window of ActiveSync. 18. Is LGO used? If yes, continue with step 6. in paragraph "Connect to LGO via USB cable step-by-step".
Connect to LGO via USB cable step-by-step Description 1. Start the PC. 2. Plug the GEV161 cable into RX1250. 3. Turn the RX1250 on. 4. Plug the GEV161 cable into the USB port of the PC. ) ActiveSync starts up automatically. If does not start automatically, start ActiveSync. If not already installed, run the ActiveSync installation program. 5. Allow USB connections inside the Connection Settings window of ActiveSync. 6. Start LGO or install it if not available. 7.
RX1200 Getting Started with SmartWorx Connect to PC via USB cable step-by-step 104 Description 1. Start the PC. 2. Plug the GEV161 cable into RX1250. 3. Turn the RX1250 on. 4. Plug the GEV161 cable into the USB port of the PC. ) ActiveSync starts up automatically. If does not start automatically, start ActiveSync. If not already installed, run the ActiveSync installation program. 5. Allow USB connections inside the Connection Settings window of ActiveSync. 6. Click on Explore in ActiveySync.
Via Bluetooth step-by-step Description 1. Activate Bluetooth on the PC. The steps required depend on the Bluetooth driver and other PC specific configurations. On the PC, always ensure that • the correct COM port is defined. • the COM port is configured as incoming, which allows Bluetooth devices to detect the PC. 2. Turn the RX1250 on. 3. Go to Start/Settings/Control Panel/Bluetooth Device. 4. Click Scan Device. 5. Highlight the service required in the Untrusted box. 6.
RX1200 Getting Started with SmartWorx 106 Description 10. Go to Start/Settings/Control Panel/PC Connection. 11. Select Bluetooth from the combo box. 12. Go to Start/Programs/Communication/ActiveSync to initialise the communication. ) As soon as the communication is initialised on the RX1250, ActiveSync establishes the link between the PC and RX1250. 13. Start LGO or install it if not available. 14. Goto Data Exchange Manager in LGO. 15. Click Refresh on the ActiveSync folder. 16.
4.9 Connecting to a Radio (for Remote Control Surveys) 4.9.
RX1200 Getting Started with SmartWorx 4.9.2 108 Working in Remote Mode Description Access step-by-step In the remote mode TPS is controlled from RX. To work in this mode TPS must be set to RCS mode. Refer to TPS1200+/TPS1200 Technical Reference Manual for more information. While in RCS mode TPS can still be controlled with the keys on the instrument. Description 1. ) Proceed to the local menu of RX. Select Main Configuration Menu: Radio/Comms Settings, Modes page. 2. Set .
4.9.3 Working in Transparent Mode Description Access step-by-step enables the remote control of TPS with GeoCOM commands. RX becomes a transparent radio modem, like the RadioHandle or TCPS27B. GeoCOM commands can be sent from a computer to RX which are then sent to TPS via RadioHandle or TCPS27B. These commands will be executed on TPS and results can be sent back. Description 1. ) ) From CONFIGURE Interfaces on TPS ensure that GeoCOM Mode is turned on and RCS Mode is turned off.
RX1200 Getting Started with SmartWorx 4.9.4 110 Working in Semi-Transparent Mode Description ) Access step-by-step enables the total remote control of TPS in RCS mode but the data being captured by TPS will be sent via radio link to the LEMO port of RX. A computer connected to this port will receive the data captured on TPS in real-time. Data being sent over the radio link in this mode is not protected by a Leica protocol.
4.10 Connecting to the SmartAntenna Connecting step-by-step Description 1. Select Main Menu: Config...\Interfaces... in the Leica software. 2. Highlight SmartAntenna. 3. EDIT (F3) 4. CONFIGURE SmartAntenna Interface
RX1200 Getting Started with SmartWorx 112 Description All available Bluetooth devices are displayed. 10. Highlight the SmartAntenna to be used. 11. CONT (F1) ) ) If the SmartAntenna selected is connected for the first time, a Windows CE authentication request comes up. Type in 0000 as identification number for Leica’s Bluetooth and click OK. Once the Bluetooth connection is established, the Bluetooth LED on the SmartAntenna starts flashing in blue.
Getting Started with SmartWorx RX1200 113
RX1200 Local Mode 5 5.1 ) Access 114 Local Mode Accessing the Main Configuration Menu This menu is always available to RX1210/RX1210T. This menu is only available to the RX1250 models when in terminal mode. Press USER for 2 s or automatically after 10 s when no sensor can be detected. A message is displayed for a period of 10 s. Next step IF the RX is to be THEN configured CONF (F2) leads directly to Main Configuration Menu. connected automatically AUTO (F3) initiates the auto detect function.
5.2 Overview of the Main Configuration Menu Main Configuration Menu Description of main menu functions Main menu function Description Refer to chapter Choose Sensor Select the sensor to be working with RX. 5.3 Local Settings Change or adjust the display and sound settings of RX. 5.4 Radio/Comms Settings Change or adjust the communication settings 5.5 of RX. Work with Sensor Local Mode Leave the Local Mode and work with the selected sensor. RX1200 5.
RX1200 Local Mode 5.3 116 Choosing a Sensor Access step-by-step Description 1. Refer to "5.1 Accessing the Main Configuration Menu" to access the menu 2. Main Configuration Menu Highlight Choose Sensor. 3. CONT (F1). Choose Sensor Description of fields Field Option Description Sensor TPS1200+/ TPS1200 Sets RX to work with TPS1200+/TPS1200. Choose this option if working only TPS1200+/TPS1200. GPS1200 Sets RX to work with GPS1200. Choose this option if working only GPS1200.
5.4 Local Settings Description Access step-by-step The settings on this screen allow the screen appearance to be configured, turn the notification beeps on and off and define the behaviour of the keys. The settings are stored on RX itself. Description 1. Refer to "5.1 Accessing the Main Configuration Menu" to access the menu 2. Main Configuration Menu Highlight Local Settings. 3. CONT (F1).
RX1200 Local Mode 118 Field Option Description Off, Always On, On for 30 s, On for 1 min, On for 2 min or On for 5 min Controls the screen illumination to be on, off or on for the specified time after the last key was pressed or touch screen event. Off, Always On, or Controls the keyboard illumination. Same as Screen From 0% to 100% For RX1210/RX1210T only. For RX1210/RX1210T only.
Next step IF THEN the local settings are to be exited CONT (F1) accepts changes and returns to the screen from where this screen was accessed. the touch screen is to be calibrated CALIB (F5) calibrates the touch screen. the next page is to be accessed Local Settings, Beeps page Local Mode PAGE (F6) changes to another page. Description of fields Field Option Description Off, Soft or Loud Controls the beep for acoustic warning signals.
RX1200 Local Mode Local Settings, More page 120 Description of fields Field Option Description Choicelist Allows the local mode functions to be displayed in different languages. The language setting does not affect the language displayed when working with a sensor. When working with a sensor, the language selected in the sensor is shown on RX. None RX does not switch off automatically. RX Off After the preset time of RX inactivity, RX switches off.
5.5 Radio Settings 5.5.1 Radio Communication Settings Description Access step-by-step Allows changes to the communication parameters of RX. Description 1. Refer to "5.1 Accessing the Main Configuration Menu" to access the menu 2. Main Configuration Menu Highlight Radio/Comms Settings. 3. CONT (F1). Radio/Comms Settings, Modes page Description of fields Field Option Description RCS Mode Local Mode RX1200 RX operates as a secondary control unit for TPS1200+/TPS1200.
RX1200 Local Mode Field 122 Option Description Transparent Deactivates the software functionality of RX, converting it into a radio modem which can be used with GFU23, RadioHandle or TCPS27B to communicate remotely with TPS1200+/TPS1200. Refer to "4.9.3 Working in Transparent Mode" for more information. SemiTransparent Enables measurement data to be sent from TPS1200+/TPS1200, via the radio link, to the LEMO port of RX in real-time.
Next step Radio/Comms Settings, Param page Local Mode IF THEN the local settings are to be exited CONT (F1) accepts changes and returns to the screen from where this screen was accessed. the next page is to be accessed PAGE (F6) changes to another page on this screen Description of fields Field Option Description From 0 to 15 Assigned channel number enabling multiple pairs of radios to work simultaneously in the same area without interfering with each other.
RX1200 Local Mode 124 Field Option Description Output The terminator of a data packet. Output Number of bits in a block of digital data. Output Number of bits to end a block of digital data. Remote Sets the internal radio into a remote mode. The radio modules inside GFU23, RadioHandle or TCPS27 and RX must be set to opposite settings. It is recommended to set RX to remote and the GFU23, RadioHandle or TCPS27 to base.
IF THEN radio settings are to EXT R (F4) displays and allows editing of TCPS27 external be edited radio settings when connected to the LEMO port. radio settings are to SYNC (F5) synchronises the settings between the internal be synchronised radio of RX and external radio GFU23, TCPS27B when connected to each other via cable. Open Radio/Comms Settings, Param page to change the parameters for the communication between the radios.
RX1200 Local Mode 5.5.2 126 Configuring the Radios View/edit internal/external radio settings step-by-step Description 1. Open Radio/Comms Settings, Param page. 2. • • For RX1250T/RX1250Tc the internal radio settings are displayed. For other models the external radio settings are displayed, when a radio is connected. ) ) DEFLT (F3) to reset to Leica default values 3. Edit settings. EXT R (F4) to view the external radio settings when a radio is connected to RX. 4.
Description 3. SYNC (F5). 4. Open Radio/Comms Settings, Param page. 5. The settings of the internal radio of RX are displayed. 6. Edit settings.
RX1200 Local Mode 5.6 128 Working with a Sensor Description Exit Configuring step-by-step This function allows to leave the Main Configuration Menu and returns to working with the sensor. Description 1. ESC until Main Configuration Menu is displayed. 2. Main Configuration Menu Highlight Work with Sensor. 3. CONT (F1).
Local Mode RX1200 129
RX1200 Care and Transport 6 6.1 130 Care and Transport Transport Transport in a road vehicle Never carry the product loose in a road vehicle, as it can be affected by shock and vibration. Always carry the product in its transport container and secure it. Shipping When transporting the product by rail, air or sea, always use the complete original Leica Geosystems packaging, transport container and cardboard box, or its equivalent, to protect against shock and vibration.
6.2 Storage Product Respect the temperature limits when storing the equipment, particularly in summer if the equipment is inside a vehicle. Refer to "9 Technical Data" for information about temperature limits. Li-Ion batteries • Refer to "9 Technical Data" for information about storage temperature range. • A storage temperature range of -20 to +30°C/-4 to 86°F in a dry environment is recommended to minimise self-discharging of the battery.
RX1200 Care and Transport 6.3 132 Cleaning and Drying Product and accessories Use only a clean, soft, lint-free cloth for cleaning. If necessary, moisten the cloth with water or pure alcohol. Do not use other liquids; these may attack the polymer components. Damp products Dry the product, the transport container, the foam inserts and the accessories at a temperature not greater than 40°C / 104°F and clean them. Do not repack until everything is completely dry.
Care and Transport RX1200 133
RX1200 Safety Directions 7 7.1 134 Safety Directions General Introduction Description The following directions should enable the person responsible for the product, and the person who actually uses the equipment, to anticipate and avoid operational hazards. The person responsible for the product must ensure that all users understand these directions and adhere to them.
7.2 Intended Use Permitted use Adverse use Safety Directions • Remote control of product. • Data communication with external appliances. • Use of the product without instruction. • Use outside of the intended limits. • Disabling safety systems. • Removal of hazard notices. • Opening the product using tools, for example screwdriver, unless this is specifically permitted for certain functions. • Modification or conversion of the product. • Use after misappropriation.
Safety Directions Warning RX1200 136 Adverse use can lead to injury, malfunction and damage. It is the task of the person responsible for the equipment to inform the user about hazards and how to counteract them. The product is not to be operated until the user has been instructed on how to work with it.
7.3 Limits of Use Environment Suitable for use in an atmosphere appropriate for permanent human habitation: not suitable for use in aggressive or explosive environments. Danger Local safety authorities and safety experts must be contacted before working in hazardous areas, or in close proximity to electrical installations or similar situations by the person in charge of the product.
RX1200 Safety Directions 7.4 138 Responsibilities Manufacturer of the product Leica Geosystems AG, CH-9435 Heerbrugg, hereinafter referred to as Leica Geosystems, is responsible for supplying the product, including the user manual and original accessories, in a completely safe condition.
Warning Safety Directions The person responsible for the product must ensure that it is used in accordance with the instructions. This person is also accountable for the training and the deployment of personnel who use the product and for the safety of the equipment in use.
RX1200 Safety Directions 7.5 140 End User Licence Agreement EULA EULA terms • You have acquired a device RX1250 that includes software licenced by Leica Geosystems from an affiliate of Microsoft Corporation ("MS"). Those installed software products of MS origin, as well as associated media, printed materials, and "online" or electronic documentation ("SOFTWARE") are protected by international intellectual property laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved.
Geosystems TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE. • NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is provided "AS IS" and with all faults. THE ENTIRE RISK AS TO SATISFACTORY QUALITY, PERFORMNCE, ACCURACY, AND EFFORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU. ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OF AGAINST INFRINGEMENT.
Safety Directions RX1200 142 except and only to the extent that such activity is expressly permitted by applicable law notwithstanding these limitation. • SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS. You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the Device, and only if the recipient agrees to this EULA. If the SOFTWARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE. • EXPORT RESTRICTIONS.
7.6 Hazards of Use Warning The absence of instruction, or the inadequate imparting of instruction, can lead to incorrect or adverse use, and can give rise to accidents with far-reaching human, material, financial and environmental consequences. Precautions: All users must follow the safety directions given by the manufacturer and the directions of the person responsible for the product.
Safety Directions RX1200 144 Warning If the product is used with accessories, for example masts, staffs, poles, you may increase the risk of being struck by lightning. Precautions: Do not use the product in a thunderstorm. Warning During dynamic applications, for example stakeout procedures there is a danger of accidents occurring if the user does not pay attention to the environmental conditions around, for example obstacles, excavations or traffic.
Warning Only Leica Geosystems authorized service workshops are entitled to repair these products. Warning If computers intended for use indoors are used in the field there is a danger of electric shock. Precautions: Adhere to the instructions given by the computer manufacturer with regard to field use in conjunction with Leica Geosystems products.
Safety Directions RX1200 146 Caution During the transport, shipping or disposal of batteries it is possible for inappropriate mechanical influences to constitute a fire hazard. Precautions: Before shipping the product or disposing of it, discharge the batteries by running the product until they are flat. When transporting or shipping batteries, the person in charge of the product must ensure that the applicable national and international rules and regulations are observed.
Warning Short circuited battery terminals can overheat and cause injury or fire, for example by storing or transporting in pockets if battery terminals come in contact with jewellery, keys, metallized paper or other metals. Precautions: Make sure that the battery terminals do not come into contact with metallic objects. Warning If the product is improperly disposed of, the following can happen: • If polymer parts are burnt, poisonous gases are produced which may impair health.
Safety Directions RX1200 148 Product specific treatment and waste management information can be downloaded from the Leica Geosystems home page at http://www.leica-geosystems.com/treatment or received from your Leica Geosystems dealer.
7.7 Electromagnetic Compatibility EMC Description The term Electromagnetic Compatability is taken to mean the capability of the product to function smoothly in an environment where electromagnetic radiation and electrostatic discharges are present, and without causing electromagnetic disturbances to other equipment. Warning Electromagnetic radiation can cause disturbances in other equipment.
Safety Directions RX1200 150 Caution Disturbances caused by electromagnetic radiation can result in erroneous measurements. Although the product meets the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possibility that the product may be disturbed by very intense electromagnetic radiation, for example, near radio transmitters, two-way radios or diesel generators.
Radios or digital cellular phones Warning Safety Directions Use of product with radio or digital cellular phone: Electromagnetic radiation can cause disturbances in other equipment, in installations, in medical devices, for example pacemakers or hearing aids and in aircraft. It can also affect humans and animals.
RX1200 Safety Directions 7.8 152 FCC Statement, Applicable in U.S. Applicablility Warning The grayed paragraph below is only applicable for RX1210 products without radio. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Warning Labelling RX1210/RX1210T Changes or modifications not expressly approved by Leica Geosystems for compliance could void the user's authority to operate the equipment. Type: RX1210 ....... ................. ............ ............ ............ ................. ................. ................. ................. ................. This device complies with part 15 of the FCC Rules.
RX1200 Safety Directions Labelling all RX1250 models Type: RX1250 ........... ................... ........... ................. ................. ................. ................. ................. 154 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Labelling GHT56 Type: GHT 56 ....... .................. .................. .................. .................. .......... .......... ......... ......... This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RX1200 Safety Directions Labelling GFU23, GFU24 Type: GFUXX ......... ................. ................... ................... ................... ................... ................... ................... This device complies with part 15 of the FCC Rules.
Labelling GFU19, GFU25, GFU26 Type: GFUXX ......... ................. ................... ................... ................... ................... ................... ................... This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RX1200 Safety Directions Labelling internal battery GEB211, GEB221 .. .... ........ .... .... .... .... .. .... .... ........ .... .... .... ........ .... .. .. .... .... ........ .... ...... .... .... .... .... . .... ........ .... .... ................ .... .. ... .... .... ........ .... .... ........ .... .... ........ .. .... ........ .... .... ... .... .... .. TPS12_082 This device complies with part 15 of the FCC Rules.
Labelling USB cable GEV161 Type: GEV161 Power: 3,3V / 0,005mA Leica Geosystems AG CH-9435 Heerbrugg Manufactured: 08.2005 Made in Switzerland RX12_027 Safety Directions Art.No.: 733281 S.No.: 0055 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RX1200 Trouble Shooting 8 160 Trouble Shooting Turning on and communicating with the instruments Problem Details To be checked RX does not turn on all RX1250 models with a battery • RX1210/RX1210T • RX does not connect to TPS1200+/ TPS1200 Via the radio link Battery fully charged. Clip-on connection to GPS1200. • Cable connection to GPS1200 RX port. • Connection to a fully charged battery.
Problem Trouble Shooting Details To be checked RX1200 • TPS1200+/TPS1200 is set to work in RCS mode. Refer to TPS1200+/TPS1200 Technical Reference Manual. • The base radio is connected to the instrument and a fully charged external battery. • RX and the base radio are within radio range. • The radio settings in RX and the base radio are correct. Refer to "5.5 Radio Settings". Radio settings should be synchronised to Leica default values.
RX1200 Trouble Shooting Problem RX does not connect to GPS1200 162 Details To be checked Via cable • or is selected in Main Configuration Menu: Choose Sensor on the controller. Refer to "5.3 Choosing a Sensor". • is selected in Main Configuration Menu: Radio/Comms Settings on the Modes page. Refer to "5.5 Radio Settings". • Proper physical connection of cable to TPS1200+/TPS1200 and the controller.
Problem Details To be checked Via cable RX1250 does not connect to SmartAntenna Via Bluetooth Via cable Trouble Shooting RX1200 • or is selected in Main Configuration Menu: Choose Sensor on RX. Refer to "5.3 Choosing a Sensor". • RX is properly connected to GPS1200. • or is selected in Main Configuration Menu: Choose Sensor on RX. Refer to "5.3 Choosing a Sensor". • SmartAntenna battery is charged.
RX1200 Trouble Shooting Radio performance Problem Details Radio range not optimal RX1250 communicating with radio/digital cellular phone 164 To be checked • TCPS27B is mounted onto the tripod using the adapter. Refer to "3.1.4 Setting up for Remote Control (with the RadioHandle)". • Change the link number if it is suspected to have other 2.4 GHz radios operating in the area, this measure may reduce interference and improve radio performance. Refer to "5.5 Radio Settings".
Problem RX1250 does not recognise radio RX1250 recognising CompactFlash card Trouble Shooting Details To be checked Via GHT56 • Battery of digital cellular phone fully charged. • RX1250 is properly connected to GHT56 via clip-on-contacts. • Battery of radio fully charged. The radio is powered by the battery attached to GHT56. If the LED indicator on GHT56 is green, then power is okay.
RX1200 Trouble Shooting RX1250 Windows CE RX1250 Bluetooth connection to PC 166 Problem Details To be checked Icons not on Windows CE desktop Icon to display Leica software • Tap the Start button in the bottom left corner of Windows CE desktop. Then select Programs\Leica Geosystems. • Access the Windows directory from the Windows CE Explorer. Copy the Leica software icon and paste it to the Windows CE desktop. The Leica software icon may be a hidden file.
Problem Trouble Shooting Details To be checked RX1200 • Is the device properly detected and the driver loaded? • Go to My Computer/Manage/Device Management. Check the settings of the Bluetooth device. • Check the Bluetooth device settings, for example the Options and COM ports pages. • Is ActiveSync running? Is the correct COM port defined in the Connection Settings dialog? • Re-boot the PC or/and RX1250.
RX1200 Technical Data 9 9.1 168 Technical Data RX Technical Data Design Glass reinforced polymer housing with optional integrated battery and radio modem.
Weight Recording Type Weight [kg]/[lbs] RX1210/RX1210T 0.480/1.058 RX1250T/RX1250Tc, with GEB211, with Internal Radio 0.795/1.753 RX1250X/RX1250Xc, with GEB211 0.741/1.634 For all RX1250 models, data can be recorded on the CompactFlash card.
RX1200 Technical Data Power 170 Type Consumption [W] External supply voltage RX1210/RX1210T 1 Nominal voltage 12 V DC ( ) Voltage range 11.5 V-28 V RX1250T/ RX1250Tc 1.6/ 1.8 Bluetooth to SmartAntenna, digital cellular phone powered from GHT56 Nominal voltage 12 V DC ( ) Voltage range 11.5 V-28 V RX1250X/ RX1250Xc 1.1/ 1.4 Bluetooth to SmartAntenna, digital cellular phone powered from GHT56 Nominal voltage 12 V DC ( ) Voltage range 11.
Internal battery Environmental specifications Technical Data Type Battery Voltage Capacity Operating time, typical RX1250T/ RX1250Tc Li-Ion 7.4 V GEB211: 2.2 Ah 10 h/ 9h Radio link to instrument RX1250X/ RX1250Xc Li-Ion 7.4 V GEB211: 2.
RX1200 Technical Data 172 Protection against water, dust and sand Type Protection all models IP67 (IEC60529) Dusttight Waterproof to 1 m temporary immersion Humidity Interfaces Type Protection all models Up to 100 % The effects of condensation are to be effectively counteracted by periodically drying out RX.
Data format for RS232 Ports Technical Data The default values are: Baud rate: Parity: Terminator: Data bits: Stop bits: 115200 None CR/LF 8 1 Type 8 pin LEMO-1 all models For power and/or communication For communication to GHT56 and GPS1200 RX1200 Special clip-on interface 173
RX1200 Technical Data 9.2 SmartAntenna Technical Data 9.2.1 Tracking Characteristics Receiver technology SmartTrack+ (ATX1230 GG) Satellite reception Dual frequency Receiver channels ATX1230 GG: Supported codes GPS 174 14 channels continuous tracking on L1 and L2 (GPS); twelve channels continuous tracking on L1 and L2 (GLONASS); two channels tracking SBAS.
GLONASS Carrier tracking Type L1 L2 ATX1230 GG Carrier phase, C/A code Carrier phase, P2 code GPS Condition ATX1230 GG L1, AS off or on Reconstructed carrier phase via C/A code L2, AS off Reconstructed carrier phase via P2 code L2, AS on Switches automatically to patented P code-aided technique providing full L2 reconstructed carrier phase GLONASS Condition Technical Data ATX1230 GG L1 Reconstructed carrier phase via C/A code L2 Reconstructed carrier phase via P2 code RX1200 175
RX1200 Technical Data Code measurements 176 GPS Condition ATX1230 GG L1, AS off L1, AS on Carrier phase smoothed code measurements: C/A code L2, AS off Carrier phase smoothed code measurements: P2 code L2, AS on Carrier phase smoothed code measurements: Patented P code-aided code GLONASS Condition ATX1230 GG L1 Carrier phase smoothed code measurements: C/A code L2 Carrier phase smoothed code measurements: P2 code ) Carrier phase and code measurements on L1 and L2 are fully independent with
9.2.2 Accuracy ) Accuracy is dependent upon various factors including the number of satellites tracked, constellation geometry, observation time, ephemeris accuracy, ionospheric disturbance, multipath and resolved ambiguities. The following accuracies, given as root mean square, are based on measurements processed using LGO and on real-time measurements.
RX1200 Technical Data 9.2.3 178 Technical Data Description and use The SmartAntenna is selected for use based upon the application. The table gives a description and the intended use of the SmartAntenna. Type Description ATX1230 GG L1/L2 SmartTrack+ antenna with With RX1250 or built in groundplane. TPS1200+/TPS1200. Dimensions Height: Diameter: Connector 8 pin LEMO-1 Mounting 5/8" Whitworth Weight 1.
Battery internal Electrical data Type: Voltage: Capacity: Typical operating time: Li-Ion 7.4 V GEB211: 2.2 Ah 5.7 h Type ATX1230 GG Voltage - Current - Frequency GPS L1 1575.42 MHz GPS L2 1227.60 MHz GLONASS L1 1602.5625-1611.5 MHz GLONASS L2 1246.4375-1254.
RX1200 Technical Data Environmental specifications 180 Temperature Operating temperature [°C] Storage temperature [°C] -40 to +65 -40 to +80 Bluetooth: -30 to +65 Protection against water, dust and sand Protection IP67 (IEC 60529) Dusttight Protected against water jets Waterproof to 1 m temporary immersion Humidity Protection Up to 100 %
Protection The effects of condensation are to be effectively counteracted by periodically drying out the antenna.
RX1200 Technical Data 9.3 182 GHT56 Technical Data Dimensions Length: Width: Thickness: Connector • 8 pin LEMO-1 • 7 pin clip-on-contacts 0.169 m 0.123 m 0.130 m Weight 0.460 kg including internal battery GEB211 Power Power consumption: Nominal voltage 7.4 V DC ( Battery Type: Voltage: Capacity: Typical operating time: Li-Ion 7.4 V GEB211: 2.2 Ah, GEB221: 4.4 Ah The given operating times are valid for • one fully charged GEB221 battery. • 25°C.
GFU14, receive only mode: 16.8 h GFU24: 7.1 h Pacific Crest radio, receive only mode: 15.
RX1200 Technical Data Humidity Protection Up to 100 % The effects of condensation are to be effectively counteracted by periodically drying out the antenna.
9.4 Conformity to National Regulations 9.4.1 RX1210 Conformity to national regulations Technical Data Hereby, Leica Geosystems AG, declares that the product RX1210 is in compliance with the essential requirements and other relevant provisions of the applicable European Directives The declaration of conformity may be consulted at http://www.leica-geosystems.com/ce.
RX1200 Technical Data 9.4.2 186 RX1250, GFU23 Conformity to national regulations • • • Frequency band FCC Part 15 (applicable in US) Hereby, Leica Geosystems AG, declares that the RX1250 and GFU23 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at http://www.leica-geosystems.com/ce.
Output power Type Output power [mW] all RX1250 models (Bluetooth) 2.
RX1200 Technical Data 9.4.3 188 GFU24, Siemens MC75 Conformity to national regulations • • • FCC Part 15, 22 and 24 (applicable in US) Hereby, Leica Geosystems AG, declares that the GFU24 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at http://www.leica-geosystems.com/ce.
Antennas Specific Absorption Rate (SAR) Technical Data Type GAT 3 GAT 5 Frequency band 900 or 1800 MHz 850 or 1900 MHz Type Detachable λ/2 antenna Detachable λ/2 antenna Gain 0 dBi 0 dBi Connector TNC TNC The product meets the limits for the maximum permissible exposure of the guidelines and standards which are force in this respect. The product must be used with the recommended antenna.
RX1200 Technical Data 9.4.4 190 GFU19 (US), GFU25 (CAN), GFU26 (US) CDMA MultiTech MTMMC-C Conformity to national regulations • FCC Part 15, 22 and 24 (applicable in US) • The conformity for countries with other national regulations not covered by the FCC part 15, 22 and 24 has to be approved prior to use and operation. Frequency band Dual-Band CDMA850/CDMA1900 MHz Output power CDMA850: CDMA1900: Antenna 2W 0.
Specific Absorption Rate (SAR) Technical Data The product meets the limits for the maximum permissible exposure of the guidelines and standards which are force in this respect. The product must be used with the recommended antenna. A separation distance of at least 20 centimeters should be kept between the antenna and the body of the user or nearby person within the intended application.
RX1200 Technical Data 9.4.5 192 SmartAntenna with Bluetooth Conformity to national regulations • • • Frequency band FCC Part 15 (applicable in US) Hereby, Leica Geosystems AG, declares that the SmartAntenna with Bluetooth is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at http://www.leica-geosystems.com/ce.
Output power Antenna Technical Data Type Output power [mW] GNSS Receive only Bluetooth 5 GNSS Bluetooth Internal GNSS antenna element (receive only) Type: Internal Microstrip antenna Gain: 1.
International Limited Warranty, Software Licence Agreement 10 RX1200 194 International Limited Warranty, Software Licence Agreement International Limited Warranty This product is subject to the terms and conditions set out in the International Limited Warranty which you can download from the Leica Geosystems home page at http://www.leica-geosystems.com/internationalwarranty or collect from your Leica Geosystems distributor.
Such agreement is provided together with all products and can also be referred to and downloaded at the Leica Geosystems home page at http://www.leica-geosystems.com/swlicense or collected from your Leica Geosystems distributor. You must not install or use the software unless you have read and accepted the terms and conditions of the Leica Geosystems Software Licence Agreement.
Directory Structure of the Memory Device RX1200 196 Appendix A Directory Structure of the Memory Device Description On the memory device, files are stored in certain directories. The following diagram of the directory structure refers to both CompactFlash card and internal memory if fitted. Backwards compatible with Leica GPS System 500 are geoid field files, CSCS field files and GSI files.
| | | | | | |—— DBX | | | | | | | |—— GPS | | | | |—— GEOID | | |—— RINGBUF | Geoid field files (*.gem) • Ring buffer files • Job files, various files • DTM jobs, various files • System 1200 coordinate system file (Trfset.dat) Antenna file (List.ant) • • |—— GSI | | | |—— SYSTEM Directory Structure of the Memory Device • • RX1200 GSM/Modem station list (Stations1200.fil) GSI files (*.gsi) • ASCII files for export from job (*.*) • Application program files (*.a*) • Firmware files (*.
RX1200 Cables 198 Appendix B Cables Description Some applications require the connection of instruments, devices or accessories to the RX. In this chapter, the required cables and their use are listed. Cables connecting instruments, devices or accessories The table shows in alphabetical order which instruments, devices or accessories can be connected using cables. Refer to paragraph "Cables and product names" for a full description of these cables.
From RX1250 (all RX1250 models) TCPS27 Cables and product names Cables To Cables GRX1200 Pro/ GRX1200 GG Pro • GEV163 • GEV164 SmartAntenna • GEV173 • GEV215 TPS1200+/ TPS1200 • GEV217 TPS1200+/ TPS1200 • GEV186 The product names of the cables in the above table are explained in detail below in ascending order. Name Description GEV71 Cable 4.0 m, LEMO to 12 V DC power supply It allows a connection to a 12 V DC power supply for example a car battery.
RX1200 Cables Name Description GEV160 Cable 2.8 m, data transfer GX COM to RS232 GEV161 Cable 2.8 m, data transfer GX RX1250 to USB GEV162 Cable 2.8 m, data transfer GX RX to RS232 GEV163 Cable 1.8 m, RX to GX GEV164 Cable 1.0 m, RX to GX, all-on-pole setup GEV171 Y-cable 1.8 m, programming cable, GFU14 to RS232 with power GEV173 Cable 1.2 m, SmartAntenna to all RX1250 models GEV186 Y-cable 1.
Cables RX1200 201
Index RX1200 202 Index A C Abbreviations ....................................................... 12 ActiveSync ................................................... 18, 101 Antenna file, directory ........................................ 197 Application program file, directory ..................... 197 Attach, clip-on-housing ........................................ 71 Cables ............................................................... 198 Cleaning and Drying .........................................
Coordinate system file, directory ....................... 197 CSCS field file, directory ................................... 196 D Data conversion .................................................. 20 Data transfer ........................................................ 20 Detach, clip-on-housing ....................................... 72 Device Clip-on-housing .............................................. 70 Status ............................................................. 77 Dimensions GHT56 ........
Index RX1200 GFU25 ............................................................... 190 GFU26 ............................................................... 190 GSI file, directory ............................................... 197 H Handstrap ............................................................ 43 Housing for devices ............................................. 70 I Icons .................................................................... 33 Indicators, LED Clip-on-housing ....................
L M Labelling GHT56 .......................................................... 155 RX1210 ........................................................ 153 RX1250 ........................................................ 154 USB cable GEV161 ...................................... 159 Language file, directory ..................................... 197 LED Clip-on-housing, description ........................... 78 GHT56, description ........................................ 69 Housing, description ................
Index RX1200 For RX .......................................................... 171 GHT56 .......................................................... 183 SmartAntenna .............................................. 180 Output power GFU19, MultiTech MTMMC-C ..................... 190 GFU24, Siemens MC75 ............................... 188 SmartAntenna .............................................. 193 P PC card drive on office computer ........................ 20 Power GHT56 ...................................
Detach from pole ............................................ 42 Firmware for all RX1250 models .................... 15 Firmware for RX1210/RX1210T ..................... 15 Operating principles ....................................... 32 Operating temperature ................................. 171 Storage temperature .................................... 171 S Screen Description of elements .................................. 30 Graphical overview ......................................... 30 Icons .............
Index RX1200 208 For RX .......................................................... 171 GHT56 .......................................................... 183 SmartAntenna .............................................. 180 System file, directory ......................................... 197 Transport of Equipment .................................... 130 Trouble Shooting ............................................... 160 Turning the RX off .........................................
Index RX1200 209
Ask your local Leica Geosystems dealer for more information about our TQM program. Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Switzerland Phone +41 71 727 31 31 www.leica-geosystems.
