User guide

ManualsBrandsMultitech ManualsAdapterCF220

CallFinder

DID

DID-to-Analog Adapter

Model CF220-DID

Cabling Guide

Summary of content (12 pages)

PAGE 1
CallFinder® DID DID-to-Analog Adapter Model CF220-DID Cabling Guide
PAGE 2
CallFinder DID Cabling Guide Model CF220-DID 82100292L Copyright © 2008 by Multi-Tech Systems, Inc. All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, Multi-Tech Systems, Inc.
PAGE 3
CallFinder Cabling Guide Introduction This guide describes the hardware setup of the CF220-DID CallFinder unit, and some preliminary considerations for its interoperation with PBX units. Instructions for software setup can be found in the User Guide. Mechanical Mounting The CF220-DID CallFinder can be surface mounted with screws spaced according to the dimensions shown. MultiTech Systems, Inc.
PAGE 4
CallFinder Cabling Guide We Supply • A CallFinder (CF220-DID) with factory-installed software • A two-piece 9 Vdc power supply with power cord • Four common telephone cables (1 for each port; RJ-11 at both ends) • A product CD that contains: (a) a system management software package for the administrator’s PC, and (b) additional documentation for administrators • This printed Cabling Guide You Supply • A nearby AC power outlet • Two nearby connections to a PBX or key phone system • One or two nearby analog
PAGE 5
CallFinder Cabling Guide CallFinder Operation The CallFinder brings analog DID services to a key telephone system or PBX that is not DID-enabled. Prerequisite: Ordering the DID Lines To operate the CallFinder system, you will need one or two DID (Direct Inward Dial) lines in your office. You must order the DID lines from your local telephone operating company (telco). A DID line allows one phone line to be associated with multiple directory numbers.
PAGE 6
CallFinder Cabling Guide Quick Hookup for CF220-DID CallFinder CF220-DID Hookup Cabling to telco DID lines. Connector at CallFinder: RJ-11. Connector at telco end: RJ-11. CHANNEL 2 CHANNEL 1 Reset Switch Power Cable Receptacle 10/100 RESET FXS/FXO DID FXS/FXO DID To Cabling to your Ethernet LAN. Earth Ground RJ-45 connector. Cabling to PBX. FXO to PBX Station Port. FXS to PBX Trunk Port. Connectors: RJ-11 at both ends. 6 MultiTech Systems, Inc.
PAGE 7
CallFinder Cabling Guide Cabling Instructions Summary: Place the CallFinder in a convenient location, and then connect it to earth ground, to your AC power outlet, to your Ethernet network, and to your telco DID service. You cannot connect the CallFinder's Extension Ports (FXS/FXO) to your PBX until after you have configured the CallFinder software. In the CallFinder software, you will configure the Extension Ports as either FXS or FXO, and this must be done before they can be connected to your PBX.
PAGE 8
CallFinder Cabling Guide Connect CallFinder to Power Insert the 9 Vdc power connector into the CallFinder’s power receptacle and fasten it with the lock nut. Connect the female end of the AC cord to the power block. Then plug the AC cord into the power outlet. Caution: Use only the 9 Vdc power transformer supplied with the CallFinder. Use of any other transformer voids the warranty and can damage the CallFinder. Lock Nut 8 MultiTech Systems, Inc.
PAGE 9
CallFinder Cabling Guide Verify powering. After power is applied, the PWR LED comes on immediately but there is a 4-second delay before the Status LED comes on. In normal operation, the Status LED will be flashing. When you apply power, the CallFinder performs a diagnostic self-test. The Status indicator flashes when the embedded processor is up and running. If the Status indicator does not flash, check that the power supply is solidly connected and that the AC outlet is live.
PAGE 10
CallFinder Cabling Guide If it is a 192.168.2.x subnet, it may clash with the CallFinder because the CallFinder’s default IP address is 192.168.2.1. To remedy such a situation, connect directly from the Admin PC to the CallFinder using an RJ45 cable until the CallFinder’s IP address has been configured. Thereafter, connect the CallFinder into the network.
PAGE 11
CallFinder Cabling Guide Identify CallFinder’s Extension Ports (FXS/FXO) for Later Hookup Caution: You must wait until after the CallFinder software has been configured before connecting the cables between the CallFinder’s Extension (FXS/FXO) Ports and the PBX. Because the CallFinder and the PBX can both supply battery power, the cable connections must be done properly. Otherwise equipment damage could occur.
PAGE 12
Patents This device is covered by one or more of the following patents: 6,031,867; 6,012,113; 6,009,082; 5,905,794; 5,864,560; 5,815,567; 5,815,503; 5,812,534; 5,809,068; 5,790,532; 5,764,628; 5,764,627; 5,754,589; D394,250; 5,724,356; 5,673,268; 5,673,257; 5,644,594; 5,628,030; 5,619,508; 5,617,423; 5,600,649; 5,592,586; 5,577,041; 5,574,725; D374,222; 5,559,793; 5,546,448; 5,546,395; 5,535,204; 5,500,859; 5,471,470; 5,463,616; 5,453,986; 5,452,289; 5,450,425; D361,764; D355,658; D355,653; D353,598; D353,1