Specifications
Table Of Contents
- Chapter 1 – Introduction
- Chapter 2 – AT Commands Overview
- Chapter 3 - General Commands
- Chapter 4 – Identification Commands
- Chapter 5 – Query Commands
- Chapter 6 – Global Configuration Commands
- Chapter 7 – Status Commands
- Chapter 8 – Communication Commands
- Fixed DTE Rate +IPR
- DTE-DCE Local Flow Control +IFC
- Set DCD Signal &C
- Set DTR Signal &D
- Set DSR Signal &S
- V.42bis Data Compression +DS
- V.42bis Data Compression Report +DR
- Hang-Up 1x Data Command +WCHD
- Automatic Answer S0
- Line Termination Character S3
- Response Formatting Character S4
- Command Edit Character S5
- Connection Completion Timeout S7
- Carrier Detect Threshold S9
- Automatic Disconnect Delay S10
- DTMF Duration and Spacing S11
- Chapter 9 – Call Control Commands
- Dial Command D
- Hang-Up Command H
- Answer a Call A
- Calling Line Identification Presentation +CLIP
- Call Waiting Indication +CCWA
- Incoming Call +RING
- Set Voice Privacy Level +WPRV
- Emergency Mode +WSOS
- Call Answered +WANS
- Call Connected +WCNT
- Call Ended +WEND
- Call Originated +WORG
- CPHS Command +CPHS
- Voice Mail Indicator +WVMI
- List Current Call State +CLCC
- Call Forwarding +CCFC
- Send Flash to Base Station +WFSH
- Send DTMF Tones +VTS
- Chapter 10 – Network Service Commands
- Serving System +CSS
- Set Rm Interface Protocol +CRM
- Signal Quality +CSQ
- Network Registration & Roaming +CREG
- Set More Preferred Rescans +WTBMPRS
- Band Preference +WBND
- Service Indication +WSRV
- Roam Preference +WRMP
- Default Cell Band +WDCB
- Roaming Indication +WROM
- Enhanced Roaming Indication +WERI
- Cell Environment and RxLev Indication +CCED
- Chapter 11 – Provisioning Control Commands
- Chapter 12 – OTASP / OTAPA Indications
- Chapter 13 – OMA / DM Control Commands
- Chapter 14 – Short Message Service Control Commands
- Send Message +CMGS
- Read Message +CMGR
- List Message +CMGL
- Delete Message +CMGD
- Preferred Message Storage +CPMS
- Set SMS Compose Language and Encoding +WSCL
- New Message Indication +CNMI
- Incoming Message Directly Displayed +CMT
- Incoming Message Stored in Memory +CMTI
- SMS Status Report Indication Directly Displayed +CDS
- SMS Message Storage Full +WMGF
- Chapter 15 – Audio Commands
- Audio Subsystem Overview
- Speaker & Microphone Selection +SPEAKER
- Microphone Gain Enable +MGE
- Microphone Gain +VGT
- Speaker Gain Control +VGR
- Digital Gain Transmit +WDGT
- Digital Gain Receive +WDGR
- Side Tone Modification +SIDET
- Echo Cancellation +ECHO
- Loudspeaker Volume Level +CLVL
- Initialize Voice Parameters +VIP
- Audio Loopback &T
- Chapter 16 – Data Commands
- Chapter 17 – TCP App AT Commands (For Non-UIP Builds)
- Configure TCP/IP +WIPCFG
- Bearer Configuration +WIPBR
- Bearer Status +WIPBR
- Service Creation +WIPCREATE
- Service Status Unsolicited Response 1 +WIPREADY
- Service Status Unsolicited Response 2 +WIPACCEPT
- Service Status Unsolicited Response 3 +WIPERROR
- Last Socket Error Query +WIPERR
- Socket Data Exchange +WIPDATA
- TCP/IP Service Option Handling +WIPOPT
- Closing a Service +WIPCLOSE
- Close Service Status +WIPPEERCLOSE
- Enable Relay Mode for SIP Dial-Up +WRLY
- Chapter 18 – Sleep Commands (Not for UIP)
- Chapter 19 – Host Application Scenarios
- Chapter 20 – Effects of AT&W, ATZ, and AT&F
- Chapter 21 – CDMA Terminology and Acronyms
- Index
Chapter 15 – Audio Commands
Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide 93
Values: <Level>
0
-84dB (no output)
1
-32dB
2
-28dB
3
-24dB
4
-20dB
5
-16dB
6
-12dB
7
-8dB
8
-4dB
9
0dB (default)
10
4dB
11
8dB
12
12dB
If no argument is supplied to the command, the default value is assumed. The configuration is
saved immediately. See the Audio Overview section for more information.
Special
Considerations:
The +CLVL gain value is added onto the +WDGR gain. Depending on the gain setting of +WDGR,
the full range of the +CLVL command may not be realized.
Example: If +WDGR is set to +12dB gain, the +CLVL command cannot add any more positive gain. Setting
the +CLVL command to +12dB gain would not yield a total of +24dB gain, since the gain stage
can only supply a maximum of +12dB gain.
The following formulas govern the total digital receive gain:
Total Gain = (WDGR Gain + CLVL Gain)
-84dB <= Total Gain <= +12dB
Initialize Voice Parameters +VIP
Description: This resets audio parameters back to factory default values.
The following parameters are restored:
Gain control (+VGR, +VGT)
Speaker & microphone selection (+SPEAKER)
Echo cancellation (+ECHO)
Side tone selection (+SIDET)
Digital gain (+WDGT, +WDGR)
Microphone gain enable (+MGE)
Loudspeaker volume level (+CLVL)
Syntax: AT+VIP
Command
Possible Responses
AT+VIP
OK
Note: Command valid