Specifications
Table Of Contents
- Chapter 1 – Introduction
- Chapter 2 – AT Commands Overview
- Chapter 3 - General Commands
- Chapter 4 – Identification Commands
- Chapter 5 – Query Commands
- Chapter 6 – Global Configuration Commands
- Chapter 7 – Status Commands
- Chapter 8 – Communication Commands
- Fixed DTE Rate +IPR
- DTE-DCE Local Flow Control +IFC
- Set DCD Signal &C
- Set DTR Signal &D
- Set DSR Signal &S
- V.42bis Data Compression +DS
- V.42bis Data Compression Report +DR
- Hang-Up 1x Data Command +WCHD
- Automatic Answer S0
- Line Termination Character S3
- Response Formatting Character S4
- Command Edit Character S5
- Connection Completion Timeout S7
- Carrier Detect Threshold S9
- Automatic Disconnect Delay S10
- DTMF Duration and Spacing S11
- Chapter 9 – Call Control Commands
- Dial Command D
- Hang-Up Command H
- Answer a Call A
- Calling Line Identification Presentation +CLIP
- Call Waiting Indication +CCWA
- Incoming Call +RING
- Set Voice Privacy Level +WPRV
- Emergency Mode +WSOS
- Call Answered +WANS
- Call Connected +WCNT
- Call Ended +WEND
- Call Originated +WORG
- CPHS Command +CPHS
- Voice Mail Indicator +WVMI
- List Current Call State +CLCC
- Call Forwarding +CCFC
- Send Flash to Base Station +WFSH
- Send DTMF Tones +VTS
- Chapter 10 – Network Service Commands
- Serving System +CSS
- Set Rm Interface Protocol +CRM
- Signal Quality +CSQ
- Network Registration & Roaming +CREG
- Set More Preferred Rescans +WTBMPRS
- Band Preference +WBND
- Service Indication +WSRV
- Roam Preference +WRMP
- Default Cell Band +WDCB
- Roaming Indication +WROM
- Enhanced Roaming Indication +WERI
- Cell Environment and RxLev Indication +CCED
- Chapter 11 – Provisioning Control Commands
- Chapter 12 – OTASP / OTAPA Indications
- Chapter 13 – OMA / DM Control Commands
- Chapter 14 – Short Message Service Control Commands
- Send Message +CMGS
- Read Message +CMGR
- List Message +CMGL
- Delete Message +CMGD
- Preferred Message Storage +CPMS
- Set SMS Compose Language and Encoding +WSCL
- New Message Indication +CNMI
- Incoming Message Directly Displayed +CMT
- Incoming Message Stored in Memory +CMTI
- SMS Status Report Indication Directly Displayed +CDS
- SMS Message Storage Full +WMGF
- Chapter 15 – Audio Commands
- Audio Subsystem Overview
- Speaker & Microphone Selection +SPEAKER
- Microphone Gain Enable +MGE
- Microphone Gain +VGT
- Speaker Gain Control +VGR
- Digital Gain Transmit +WDGT
- Digital Gain Receive +WDGR
- Side Tone Modification +SIDET
- Echo Cancellation +ECHO
- Loudspeaker Volume Level +CLVL
- Initialize Voice Parameters +VIP
- Audio Loopback &T
- Chapter 16 – Data Commands
- Chapter 17 – TCP App AT Commands (For Non-UIP Builds)
- Configure TCP/IP +WIPCFG
- Bearer Configuration +WIPBR
- Bearer Status +WIPBR
- Service Creation +WIPCREATE
- Service Status Unsolicited Response 1 +WIPREADY
- Service Status Unsolicited Response 2 +WIPACCEPT
- Service Status Unsolicited Response 3 +WIPERROR
- Last Socket Error Query +WIPERR
- Socket Data Exchange +WIPDATA
- TCP/IP Service Option Handling +WIPOPT
- Closing a Service +WIPCLOSE
- Close Service Status +WIPPEERCLOSE
- Enable Relay Mode for SIP Dial-Up +WRLY
- Chapter 18 – Sleep Commands (Not for UIP)
- Chapter 19 – Host Application Scenarios
- Chapter 20 – Effects of AT&W, ATZ, and AT&F
- Chapter 21 – CDMA Terminology and Acronyms
- Index
Chapter 15 – Audio Commands
86 Multi-Tech Systems, Inc. CDMA C1 AT Commands Reference Guide
Speaker & Microphone Selection +SPEAKER
Description: This command is used to select the voice path, and activates a speaker/microphone audio path.
The modem supports one audio path: analog1. An audio path is functional only with appropriate
external hardware.
Voice paths may be changed while a call is in progress as well as in the idle state.
Syntax: AT+SPEAKER=<n>
Command
Possible Responses
AT+SPEAKER=0
Note: Select analog1 audio path.
OK
Note: Command valid.
AT+SPEAKER
Note: Select analog1 audio path.
OK
Note: Command valid (default
path)
AT+SPEAKER?
+SPEAKER: 0
OK
Note: analog1 audio path active.
AT+SPEAKER=?
Note: Get the range of values.
+SPEAKER: (0-2)
Values: < n >
0 Analog1 – LINE_IN and HPH_OUT. (default)
1 (not supported)
2 (not supported)
If no argument is supplied to the command, the default value is assumed. The configuration is
saved immediately. The Analog 1 output is designed to drive a 32Ω speaker. See the Audio
Overview section for more information.
Microphone Gain Enable +MGE
Description: This command enables or disables the 24dB microphone gain amplifier.
Syntax: AT+MGE=<val1>
Command
Possible Responses
AT+MGE
OK
Note: Sets default value of 0
AT+MGE=0
OK
Note: Disable amplifier
AT+MGE?
Note: Interrogate value
+MGE: 1
OK
Note: Current value
AT+MGE=?
Note: Test command
+MGE : (0-1)
OK
Note: Possible values
Values: <Gain>
0 Amplifier Disabled (0dB gain) (default)
1 Amplifier Enabled (24dB gain)
If no argument is supplied to the command, the default value is assumed. The configuration is
saved immediately. See the Audio Overview section for more information.