OPERATION AND PARTS MANUAL MODEL STR46SPVG RIDE-ON POWER TROWEL (B&S VANGUARD GASOLINE ENGINE) Revision #2 (07/09/07) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
STR46SPVG — PROPOSITION 65 WARNING Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber.
STR46SPVG — SILICOSIS/RESPIRATORY HAZARDS WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis.
STR46SPVG — TABLE OF CONTENTS STOW — STR46SPVG RIDE-ON POWER TROWEL (VANGUARD ENGINE) California Proposition 65 Warning ............................. 2 Silicosis/Respiratory Warnings .................................. 3 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Training Checklist ...................................................... 6 Daily Pre-Operation Checklist ...................................
PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ ❒ ❒ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: ✓ FedEx or UPS Ground Note: Unless otherwise indicated by customer, all ✓ FedEx or UPS Second Day or Third Day orders are treated as “Standard Orders”, and will ship within 24 hou
STR46SPVG — TRAINING CHECKLIST TRAINING CHECKLIST This checklist will lists some of the minimum requirements for machine maintenance and operation. Please feel free to detach it and make copies. Use this checklist whenever a new operator is to be trained or it can be used as a review for more experienced operator’s. TRAINING CHECKLIST NO. DESCRIPTION 1 Read Operator’s Manual completely. 2 Machine layout, location of components, checking of engine oil, and hydraulic oil levels.
NOTE PAGE STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — DAILY PRE-OPERATION CHECKLIST DAILY PRE-OPERATION CHECKLIST DAILY PRE-OPERATION CHECKLIST 1 Engine Oil Level. 2 Gearbox Fluid Level. 3 Radiator Coolant Level. 4 Condition of Blades. 5 Blade Pitch Operation. 6 Safety-Stop Switch Operation. 7 Steering Control Operation. 8 Condition of Belts. COMMENTS: STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read, understand and comply with the Safety Messages and Operating Instructions could result in injury to yourself and others. This Operation Manual has been developed to provide instructions for the safe and efficient operation of the Ride-On Trowel.
STR46SPVG — SAFETY MESSAGE ALERT SYMBOLS CAUTION - Accidental Starting ALWAYS place the engine ON/OFF switch in the OFF position, when equipment is not in use. CAUTION - Rotating Blades ALWAYS keep hands and loose clothing from rotating blades. WARNING - Over Speed NEVER tamper with the factory settings of the engine governor or settings.
STR46SPVG — RULES FOR SAFE OPERATION WARNING - Read this Manual Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the Ride-On Trowel. SAFETY ■ DO NOT operate or service this equipment before you read, understand, and comply with all safety messages in this manual.
STR46SPVG — RULES FOR SAFE OPERATION WARNING - Clear Operating Area ALWAYS make sure that the operating area is clear before starting the engine. ■ AVOID wearing jewelry or loose fitting clothing that may snag on the controls or moving parts as this can cause a serious injury. ■ ALWAYS keep clear of rotating or moving parts while operating the equipment. Shut down the engine before performing service or maintenance functions. Contact with moving parts can cause serious injury.
STR46SPVG — RULES FOR SAFE OPERATION Towing Safety Precautions CAUTION - Transporting Conform to Safety Towing Regulations before transporting trowel on public roads. To reduce the possibility of an accident while transporting the equipment on public roads, always make sure the trailer that supports the equipment and the towing vehicle are in good operating condition and that both units are mechanically sound. Battery The battery contains acids that can cause injury to the eyes and skin.
STR46SPVG — RULES FOR SAFE OPERATION Maintenance Safety Emergencies ■ ALWAYS shut down the engine and disconnect battery before performing service or maintenance functions. Contact with moving parts can cause serious injury. ■ ALWAYS know the location of the nearest fire extinguisher. ■ Securely support any equipment components that must be raised. ■ NEVER lubricate components or attempt service on a running equipment. ■ ALWAYS allow the equipment a proper amount of time to cool before servicing.
STR46SPVG — DIMENSIONS/SPECIFICATIONS (TROWEL) Figure 1. STR46SPVG Dimension Specifications Table 1. STR46SPVG Specifications SPECIFICATION PARAMETER STR46SPVG (VANGUARD) A–Length – in. (cm) 97.00 (246.4) B–Width – in. (cm) 50.0 (127) C–Height – in. (cm)1 46.0 (117) Weight – lbs. (kgs.) Operating 1,000 (453) Weight – lbs. (kgs.) Shipping 1,200 (544) Sound Pressure – dBA2 95 Vibration – ft/s2 (m/ s2)3 <8.0 (2.5) Blade Tip Speed – FPM (m/s) 1216 (6.2) Engine – H.P.
STR46SPVG — SPECIFICATIONS (ENGINE) Table 2. STR46SPVG Engine Specifications Model Briggs & Stratton Vanguard 950G Type Gasoline Engine Cylinders 3 Power 31 HP (23.1 kW) @3600 rpm Maximum Torque 51.7 ft lbs. (70.1 Nm) @ 2200 rpm Displacement 58.1 cu.in. (952 cc) Bore 2.9 in. (72 mm) Stroke 3.1 in. (78 mm) Engine Oil Capacity 3.2 qt. (3 liters) Dry Weight 159 lbs. (72.3 Kg) Dimensions (L x W x H) 15.6 in. x 17.1 in. x 19.7 in. (431.3 mm x 443.2 mm x 501.
STR46SPVG — GENERAL INFORMATION STR46SPVG Ride-On Trowel Familarization The STR46SPVG Ride-On Power Trowel is designed for the floating and finishing of concrete slabs. gearbox assemblies that are enclosed in rugged cast aluminum gear cases. The main gear is a high quality bronze and steel composite. The worm gear is composed of hardened steel. Take a walk around the STR46SPVG Ride-On Power Trowel.
STR46SPVG — CONTROLS AND INDICATORS one function. The functions of each control or indicator is described below and on the next page. 11. Charge Indicator - Lights red when electrical system is not charging properly. 1. 12. Hour Meter - Indicates number of hours machine has been in use or hours engine was run. Seat – Place for operator to sit. Engine will not start unless operator is seated. Seat is adjustable, fore and aft for operator comfort. 2.
STR46SPVG — CONTROLS AND INDICATORS 20. Kill Switch – Shuts down engine when operator is not sitting in seat . 21. Radiator/Filler Cap – Holds coolant or water necessary to keep engine at a safe operating temperature. Remove this cap to add water or antifreeze. 22. Lift Loops – Located on both the left and right sides of the main frame. Used when the trowel must be lifted onto a concrete slab. 23. Lights – Four 12 volt halogen lights are provided with this unit. 24.
STR46SPVG — ENGINE COMPONENTS Figure 4. Engine Components The following refer to the basic engine components for reference (Figure 4). Refer to the manufacturer's engine manual for instructions and details of operation and servicing. The engine shown above is a Briggs & Stratton Vanguard gasoline engine. Operation for other types of engines may vary somewhat. 1. Thermostat-– Regulates the temperature of the engine coolant. 2. Oil Filler Cap – Remove to add engine oil. 3.
STR46SPVG — SETUP Trowel Setup Instructions The purpose of this section is to assist the user in the setting up of a NEW trowel. If your trowel is already assembled (seats, handles, knobs and battery, then this section can be skipped. NOTE The new ride-on trowel cannot be put into service until the setup installation instructions are completed. These pre-setup instructions only need to be performed at the time of unpacking a NEW trowel.
STR46SPVG — INSPECTION 1. 2. Check and clean battery terminals for corrosion. Check and keep battery electrolyte between upper and lower limits indicated on the battery. Never operate or recharge without sufficient fluid in the battery. 3. Never attempt to charge a battery that is frozen. The battery can explode unless first allowed to thaw. 4. Disconnect the negative terminal ( - ) of the battery during storage.
STR46SPVG — OPERATION Important Information Before You Start 1. This ride-on trowel is equipped with a safety "safety stop switch". This switch is located beneath the seat assembly. Remember the engine will not start unless an operator is sitting in the operator’s seat. The weight of an operator depresses an electrical switch which will allow the engine to start. 2. Keep your foot OFF the gas pedal.
STR46SPVG — OPERATION Steering 6. Two control levers located in front of the operator’s seat provide directional control for the trowel. Table 3 illustrates the various directional positions of the joysticks and their effect on the ride-on trowel. Try adjusting the pitch of the blades. This can be done with the ride-on trowel stopped or while the trowel is moving, whatever feels comfortable. Test the operation of optional equipment like retardant spray and lights if equipped. 7.
STR46SPVG — MAINTENANCE (ENGINE) MAINTENANCE When performing any maintenance on the trowel or engine, follow all safety messages and rules for safe operation stated at the beginning of this manual. At the front of the book there is a “Daily Pre-Operation Checklist”. Make copies of this checklist and use it on a daily basis. Air Filter (As Required) Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessary.
STR46SPVG— MAINTENANCE (ENGINE) Changing Engine Oil (200 Hours) 1. 2. 3. Change the engine oil after the first 50 hours of use, then change every 6 months or 200 hours. Drain oil while engine is warm. Remove the oil filler cap (Figure 11), and fill engine crankcase with recommended type oil as listed in Table 4. Fill to the upper limit (F) of dipstick. Reinstall oil filler cap, start engine and run at idle for 5 minutes. Stop engine. Recheck oil level. Add oil if necessary. DO NOT over-fill.
STR46SPVG — MAINTENANCE (ENGINE/TROWEL) Radiator/Cooling System 1. Check and clean radiator fins. 2. Check cooling water. 3. Check radiator hoses for fatigue or cracking. 4. Check radiator cap sea. Refer to your engine manual for additional information. Figure 16. Spark Plug Gap Checking Drive V-Belts WARNING - BURN HAZARDS If adding coolant/antifreeze mix to the radiator, DO NOT remove the radiator cap until the unit has completely cooled.
STR46SPVG — MAINTENANCE (TROWEL) Belt Changing Procedure The belts need to be changed as soon as they show signs of wear. Remember that all belts should be changed at the same time. Do not reuse a belt under any circumstances. Indications of excessive belt wear are fraying, squealing when in use, belts that emit smoke or a burning rubber smell when in use. Under normal operating conditions, a set of belts may last approximately six months.
STR46SPVG — MAINTENANCE (TROWEL) WARNING - BURN HAZARDS ALWAYS allow the engine to cool before servicing. NEVER attempt any maintenance work on a hot! engine. ■ Pitch the blades as flat as possible and look at the adjustment bolts. They should all barely make contact with the lower wear plate on the spider. If you can see that one of them is not making contact, some adjustment will be necessary. ■ Is the machine wearing out blades unevenly (i.e.
STR46SPVG — MAINTENANCE (TROWEL) Spider Removal (Disassembly) 1. Once it is determined that an adjustment is required, remove the spider assembly from the gearbox shaft as follows: a. Locate cone point square head set screw (Figure 21) and attached jam nut found on the side of the spider assembly. b. Loosen the jam nut and cone point square head set screw, and carefully lift the upper trowel assembly off of the spider assembly.
STR46SPVG — MAINTENANCE (TROWEL) 3. Should the trowel arm inserts (bronze bushing ) come out with the trowel arm, remove the bushing from the trowel arm and set aside in a safe place. If the bushing is retained inside the spider plate, carefully remove the bushing. 4. Examine the bronze trowel arm bushing insert (Figure 24), clean if necessary. Replace bushing if out-of-round or worn. Figure 26. Typical Trowel Arm Trowel Arm Flatness Test Figure 24. Bronze Bushings Trowel Blade Removal 1.
STR46SPVG — MAINTENANCE (TROWEL) Trowel Arm Adjustment Shown in Figure 28 is the adjustment fixture with a trowel arm inserted. As each trowel arm is locked into the fixture, the arm bolt is adjusted to where it contacts a stop on the fixture. This will consistently adjust all of the trowel arms, keeping the finisher as flat and evenly pitched as possible. NOTE Arms with CLOCK-WISE blade rotation use the fixture arm in the UP position (A in Figure 39).
STR46SPVG — MAINTENANCE (TROWEL) Re-Assembly 1. Clean and examine the upper/lower wear plates and thrust collar. Examine the entire spider assembly. Wire brush any concrete or rust build-up. If any of the spider components are found to be damaged or out of round, replace them. This bolt is the contact point of the trowel arm to the lower wear plate on the thrust collar. The goal of adjustment is to promote consistent blade pitch and finishing quality. 2.
STR46SPVG — MAINTENANCE Often times, if the blades are incorrectly adjusted, they will not be able to pitch flat. This occurs when the adjusting bolts have been raised too high. Conversely, sometimes the adjusting bolts are too low and the blades cannot be pitched high enough for finishing operations. Single Pitch Control Blade pitch for one spider assembly is adjusted by rotating the crank handle on the pitch control tower for that side of the machine.
STR46SPVG — MAINTENANCE Installing Pans Onto Finisher Blades These round discs sometimes referred to as "pans" attach to the spiders arms and allow early floating on wet concrete and easy movement from wet to dry areas. They are also very effective in embedding large aggregates and surface hardeners. CAUTION - Installing Float/Finishing Pans ALWAYS install pans either on the work area or on an area that is next to and level with the work area. DO NOT lift the trowel when the pans are attached.
STR46SPVG — TROWEL TROUBLESHOOTING TABLE 5. TROWEL TROUBLESHOOTING SYMPTOM Engine running rough or not at all. Safety kill switch not functioning. If trowel “bounces, rolls concrete, or makes uneven swirls in concrete”. Machine has a perceptible rolling motion while running. POSSIBLE PROBLEM SOLUTION Kill switch malfunction? Make sure that the kill switch is functioning when the operator is seated; replace switch if necessary. Fuel? Look at the fuel system.
STR46SPVG — TROWEL TROUBLESHOOTING TABLE 5. TROWEL TROUBLESHOOTING (CONTINUED) SYMPTOM Lights not working. POSSIBLE PROBLEM SOLUTION Wiring? Check all electrical connections, including the master on/off switch and check to see if wiring is in good condition with no shor ts. Replace as necessary. Lights? Check to see if light bulbs are still good. Replace if broken. Retardant? Check the tank to make sure retardant is present. Fill tank as necessary.
STR46SPVG — ENGINE TROUBLESHOOTING TABLE 6. ENGINE TROUBLESHOOTING SYMPTOM Engine Cranks But Will Not Start Engine Starts But Will Not Continue Running POSSIBLE PROBLEM SOLUTION Fuel tank is empty. Fill fuel tank. Shut-off valve is closed. Open fuel shut-off valve. Fuel line has suction leak or is restricted. Fuel filter, or fuel tank cap vent is obstructed. Check fuel line condition and fuel line clamps. Ensure that fuel line is not kinked.
STR46SPVG — ENGINE TROUBLESHOOTING TABLE 6. ENGINE TROUBLESHOOTING (CONTINUED) SYMPTOM Engine Lacks Power POSSIBLE PROBLEM SOLUTION Air filter is obstructed. Replace air filter. Altitude causes 3% loss of horsepower per 1000 feet of altitude. If available, install high altitude jets in carburetor. Choke is par tially closed. Open choke. Faulty spark plugs or spark plug leads. Spark plug lead disconnected. Replace spark plugs or spark plug leads if faulty. Reattach spark plug lead if disconnected.
STR46SPVG — EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availibility of the parts listed. PART NO. PART NAME QTY. 12345 BOLT ....................... 1 .... WASHER, 1/4 IN. ...........
STR46SPVG — SUGGESTED SPARE PARTS 31 VANGUARD ENGINE 1 to 3 Units Qty. P/N Description 5 ................ 2829 .............. ARMS 4 ................ 10937 ............ BELT (B-37) 2 ................ 11693 ............ BOLT BATTERY 2 ................ 8381 .............. BOOT, TOGGLE SWITCH 2 ................ 11692-1 ........ BRACKET BATTERY 1 ................ 11771 ............ BRACKET ENGINE THROTTLE CABLE 11 .............. 12771 ............ BRONZE GEAR (L.S. FOR 1-1/4 SHAFT) 1 ................ 12772 ...
20947 STR46SPVG — NAMEPLATE AND DECALS ASSY. NAMEPLATE AND DECALS ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — NAMEPLATE AND DECALS ASSY. NAMEPLATE AND DECALS ASSY. NO. PART NO. PART NAME 1 11246 DECAL SET, INTERNATIONAL STDS 1A# DECAL, BELT DRIVE 1B# DECAL, GEAR DRIVE 1C# DECAL, CHECK OIL 1D# DECAL, HOT SURFACE 1E# DECAL, LIFT POINT 1F# DECAL, LUBRICATION 1G# DECAL, CLOCKWISE ROTATION 1H# DECAL, COUNTER-CLOCKWISE ROTATION 2 13118 DECAL, POWDER COATED 4 11092 DECAL, “CE” 5 35168 DECAL,ROTATING BLADE HAZARD,2.0 x 4.3 6 21455 DECAL,LIFTING/CRUSH HAZARD 7 36091 DECAL, HOT COOLANT 3.5 X 1.
STR46SPVG — PIVOT ASSY. PIVOT ASSY. 3 1 3 1 9 10 10 2 5 10 11 6 8 2 RIGHT SIDE 12 11 3 4 1 1 4 10 7 12 1 LEFT SIDE STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — PIVOT ASSY. PIVOT NO 1 2 3 4 5 6 7 8 9 10 11 12 ASSY. PART NO 0166 A 10138 1023 11248 12412-1 12413-1 1394 2145 2146 2304 2312 4196 PART NAME WASHER, LOCK, 3/8 MED. SCREW, SHS 1/4-20 X 1/2, N.P. SCREW, HHC 3/8-16 X 1 1/4 PLATE, GEARBOX ADAPTOR ARM, PIVOT RIGHT ARM, PIVOT LEFT SCREW, FHSC 3/8-16 X 1 PIVOT JOINT, SINGLE ROCKER PIVOT, DOUBLE ROCKER ROCKER BLOCK ROCKER BLOCK SCREW, HHC 3/8-16 X 3/4 QTY.
STR46SPVG — STEERING HANDLES ASSY. STEERING HANDLES ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — STEERING HANDLES ASSY. CONTROL STEERING (ASSIST) NO PART NO PART NAME 2 0189 GRIP, HANDLE 3 0447 WASHER, FLAT, 1/2 SAE 4 0735 BEARING, CONE, TIMKEN #A6075 5 0735 A BEARING, CUP, TIMKEN #A6157 9 10176 NUT, NYLOC 1/2-13 12 11138 BEARING, P-BLOCK HOUSING 47MPB 14 11141 SPACER, ROD END 15 11142 ROD END, 1/2-20 MALE RH 16 11143 ROD END, 1/2-20 FEMALE RH 17 11144 SCREW, SHC 1/2-20 X 2 PLTD 18 11145 SCREW.
STR46SPVG — STEERING ASSIST CONTROL ASSY. STEERING ASSIST CONTROL ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — STEERING ASSIST CONTROL ASSY. STEERING ASSIST CONTROL ASSY.
STR46SPVG — SINGLE PITCH HANDLE ASSY. (RIGHT AND LEFT) SINGLE PITCH HANDLE ASSY. (RIGHT AND LEFT) STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — SINGLE PITCH HANDLE ASSY. (RIGHT AND LEFT) SINGLE PITCH HANDLE ASSY. (RIGHT AND LEFT) NO PART NO PART NAME QTY. REMARKS 1#%+ 4403 CRANK KNOB 2 2#%+ 3231 SPACER 2 3#%+ 2575 CRANK LEVER 2 4#%+ 1733 HARDENED WASHER 2 5#%+ 1616 SHOULDER BOLT 2 6#% 2737 KNOB KIT ................................................................... 2 ...........
STR46SPVG — ENGINE MOUNTING BRACKETS ASSY. ENGINE MOUNTING BRACKETS ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — ENGINE MOUNTING BRACKETS ASSY. ENGINE MOUNTING BRACKETS ASSY. NO PART NO PART NAME 1 0202 SCREW, HHC 5/16-18 X 1 2 0300 B WASHER, FLAT, 5/16 SAE 3 21628-1 BRACKET, ENGINE MOUNT LEFT 4 1023 SCREW, HHC 3/8-16 X 1 1/4 5 10136 WASHER, FLAT, 3/8 SAE 6 10133 NUT, NYLOC 3/8-16 7 11155 SCREW, HHC, FT, 5/16-24 X 4” 8 6014 C NUT, HEX FINISH 5/16-24 9 11153 CAP, ENGINE ADJUST BOLT 10 5283 NUT, NYLOC 5/16-18 11 2866 SCREW, HHC M8 1.25 X 20 MM GR 8.8 12 0161 C WASHER, LOCK, 5/16 MED.
STR46SPVG — MUFFLER ASSY. MUFFLER ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — MUFFLER ASSY. MUFFLER ASSY. NO PART NO 1 12848 2 20908 3 0655 4 0300 B 5 12847 PART NAME EXHAUST FLANGE NUT MUFFLER SCREW, HHC 5/16-18 X 3/4 WASHER, FLAT 5/16 SAE EXHAUST GASKET QTY. 4 1 2 2 1 REMARKS STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — FUEL TANK ASSY. FUEL TANK ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — FUEL TANK ASSY. FUEL TANK ASSY. NO PART NO 1 4514 2 0181 B 3 0948 4 12404 5 29509 8 22067 9 11984 10 0131 A 11 825232 12 10024 13 0948 14 60013 15 22081 17 16185 PART NAME QTY. REMARKS SCREW, HHC 1/4-20 X 5/8 4 WASHER, LOCK, 1/4 MED. 6 WASHER, FLAT, 1/4 SAE 8 TANK, FUEL, STEEL 1 FUEL CAP/GAUGE, STEEL TANK 1 CLAMP, STEPLESS EAR 1/4" 6 IN-LINE FUEL FILTER 5/16 1 SCREW, HHC 1/4-20 X 3/4 2 FUEL PUMP 1 NUT, NYLOC 1/4-20 2 WASHER, FLAT, 1/4 SAE 8 HOSE, .25 ID RUBBER FUEL LINE ................ 3 FT ..
STR46SPVG — CLUTCH ASSY. CLUTCH ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — CLUTCH ASSY. CLUTCH ASSY. NO PART NO 1 12417 2 4703 3 12188 4 11994 5 10937 6 11758 7 12463 PART NAME SCREW, HHC 5/8-18 X 2 WASHER, LOCK, 5/8 MED. RETAINER, 1-7/16 BLM CLUTCH CLUTCH, F74H-3080 X 1-7/16” BELT, B37 GATES HP 11 ADAPTOR, CLUTCH, 31HP. VANGUARD SHOES/SPRINGS KIT QTY. 1 1 1 1 2 1 1 REMARKS STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — RADIATOR GUARD/ OVERFLOW BRACKET ASSY. RADIATOR GUARD/OVERFLOW BRACKET ASSY. 1 2 4 3 4 NOTES: ITEMS WITHIN DASHED LINE ARE INCLUDED WITH ENGINE. 4 REFER TO ENGINE PARTS MANUAL. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — RADIATOR GUARD/ OVERFLOW BRACKET ASSY. RADIATOR GUARD/OVERFLOW BRACKET ASSY. NO PART NO PART NAME 1 60049 TRIM EDGE, 1/32 (62B3-1/32) 2 12450 GUARD, RADIATOR (31 VAN) 3 11900 MOUNT, RADIATOR OVERFLOW 4 12464 SCREW, HHC M6-1.0 X 16mm QTY. 1.5 FT 1 1 3 REMARKS STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — V-BELT GUARD ASSY. V-BELT GUARD ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — V-BELT GUARD ASSY. V-BELT GUARD ASSY. NO PART NO 1 11819 2 1605 3 0161 C 4 21036 5 21190 6 11534 7 21197 8 20178 PART NAME SCREW, HHC 1/4-20 X 3/4 W/WASH SCREW, HHC M8-1.25 X 25mm WASHER, LOCK, 5/16 MED. BELT GUARD/MUFFLER SPPT W/A PLATE, BELT GUARD SIDE NUT, “U” TYPE, 1/4-20 PANEL, BELT GUARD REAR MUFFLER HEAT SHIELD QTY. 7 4 4 1 1 7 1 1 REMARKS STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — ENGINE SERVICE PARTS ENGINE SERVICE PARTS STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — ENGINE SERVICE PARTS ENGINE SERVICE PARTS NO PART NO PART NAME 1 496018S SPARK PLUG 2 821075 FAN BELT 3 491056 OIL FILTER 4 825557 HOSE 5 825133 HOSE 6 820026 FUEL FILTER 7 820263 ELEMENT, AIR CLEANER QTY. 1 1 1 1 1 1 1 REMARKS STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — GEARBOX ASSY. (LEFT-SIDE) GEARBOX ASSY (LEFT-SIDE) STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG— GEARBOX ASSY. (LEFT-SIDE) GEARBOX ASSY (LEFT-SIDE) NO. PART NO. PART NAME QTY. REMARKS 1% 12906 SHAFT, GEARBOX INPUT W/FAN 1 2% 5031 A SCREW, RHM 1/4-20 X1/2 4 3% 0948 WASHER, FLAT, 1/4 SAE 5 4% 12982 SHROUD, GB FIN COVER, LEFT 1 5% 12765 GEAR BOX HD RIDER 1-1/4 SHAFT .................. 1............. HOUSING ONLY 6% 0121 A FITTING, PLUG 3/8MP SQUARE HEAD 3 7% 10989 STUD, N10 - 32 X 3/4 1 8% 12907 LEFT HAND WORM 1 9% 1132 VENT, AIR 1 10% 12583 SPACER, 1.380D X 1.015 X 1.
STR46SPVG — GEARBOX ASSY. (RIGHT-SIDE) GEARBOX ASSY (RIGHT-SIDE) STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — GEARBOX ASSY. (RIGHT-SIDE) GEARBOX ASSY (RIGHT-SIDE) NO. PART NO. PART NAME QTY. REMARKS 1% 12906 SHAFT, GEARBOX INPUT W/FAN 1 2% 5031 A SCREW, RHM 1/4-20 X1/2 4 3% 0948 WASHER, FLAT, 1/4 SAE 5 4% 12981 SHROUD, GB FIN COVER, RIGHT 1 5% 12765 GEAR BOX HD RIDER 1-1/4 SHAFT .................. 1 ................ HOUSING ONLY 6% 0121 A FITTING, PLUG 3/8MP SQUARE HEAD 3 7% 10989 STUD, N10 - 32 X 3/4 1 8% 12908 RIGHT HAND WORM 1 9% 1132 VENT, AIR 1 10% 12583 SPACER, X 11D X 1.
STR46SPVG — DRIVE ASSY. DRIVE ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — DRIVE ASSY. DRIVE NO 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 21 21A# 22 23 24 25 27@ ASSY. PART NO 0126 0161 C 10133 10136 10138 10337 10514 10748 10909 11171 1146 2029 2037 2052 2090 2129 2186 2187 20186 20187 2259 11108 392052 10904 11773 PART NAME QTY. REMARKS KEY, WOODRUFF #9 4 WASHER, LOCK, 5/16 MED 12 NUT, NYLOC 3/8-16 4 WASHER, FLAT 3/8 SAE 4 SCREW, SHS 1/4-20 X 1/2, N.P. 1 BEARING, P-BLOCK, FAF YAK-1 ............... 2 ........
STR46SPVG — 5-BLADE SPIDER ASSY. (LEFT-SIDE) STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — 5-BLADE SPIDER ASSY. (LEFT-SIDE) 5-BLADE SPIDER ASSY. (LEFT) NO PART NO PART NAME QTY. REMARKS 1 12791 SPIDER ASM, LEFT SIDE (1-1/4) ..................... 1 ...........
STR46SPVG — 5-BLADE SPIDER ASSY. (RIGHT-SIDE) STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — 5-BLADE SPIDER ASSY. (RIGHT-SIDE) 5-BLADE SPIDER ASSY. (LEFT) NO PART NO PART NAME QTY. REMARKS 1 12792 SPIDER ASM, LEFT SIDE (1-1/4) ..................... 1 ...........
STR46SPVG — SEAT AND FRAME ASSY. SEAT AND FRAME ASSY. (VIEW FROM OPERATOR'S SEAT) STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — SEAT AND FRAME ASSY. SEAT AND FRAME ASSY. NO PART NO PART NAME 1 12109-1 FRAME, SEAT W/A VAN 2 11660-1 PLATE, SEAT 3 21597 BUMPER, STEM 4 21507 PLUG, PANEL 11/16 DIA. 5 5283 NUT, NYLOC 5/16-18 6 0300 B WASHER, FLAT, 5/16 SAE 7 19468 GROMMET, MINOR Z-4004 8 21936 CONNECTOR, BODY 2-PIN 9 21938 WIRE ASSY., KILL SWITCH 37" 10 21861 SEAT, ADJUSTABLE W/O ARMS 11 8081 PIN, CLEVIS 1/2X2 3/4 12 0183 PIN, COTTER 1/8X1 1/4 13 5218 SCREW, HHC 1/2-13X1 1/2 14 5054A WASHER, LOCK, 1/2 MED.
STR46SPVG — FRAME AND COMPONENTS ASSY. FRAME AND COMPONENTS STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — FRAME AND COMPONENTS ASSY. FRAME AND COMPONENTS NO PART NO PART NAME 1 12345-1 FRAME 2 4014 SCREW, 2-3/16 P-K TYPE U DRIVE 3 5065B SCREW, RHM 10-32X1/2 4 2203 WASHER, FLAT, #10 5 8126 CLAMP, HOSE SUPPORT 1/2” SMALL 6 4514 SCREW, HHC 1/4-20X5/8 7 0948 WASHER, FLAT, 1/4 SAE 8 2429 HOLDER, SPARE BELT 9 11534 NUT “U” TYPE, 1/4-20 10 4514 SCREW, HHC 1/4-20X5/8 11 20947-1 PANEL, FRONT 12 0683 PIN COTTER 3/32X3/4 13 10136 WASHER, FLAT, 3/8 SAE 14 12100 YOKE 15 9028 PIN, YOKE QTY.
STR46SPVG — FOOT PEDALS ASSY. FOOT PEDALS ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — FOOT PEDALS ASSY. FOOT PEDALS ASSY. NO PART NO 2 0300B 3 10136 4 2086 5 2772 6 5283 7 6014B 8 22035-1 9 22037-1 10 3233 11 3083 PART NAME WASHER, FLAT, 5/16 SAE WASHER, FLAT, 3/8 SAE PEDAL, ACCELERATOR PIN, ACC MOUNT NUT, NYLOC 5/16-18 PIN, COTTER 3/32X1 FOOT RISER W/A RIDER LEFT SIDE FOOT RISER W/A, RIDER ACCELERATOR SIDE WASHER, FENDER, 1.5" OD X3/8" ID SPACER QTY. REMARKS 4 2 1 1 4 2 1 1 4 1 STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — THROTTLE ASSY. THROTTLE FOOT PEDAL ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — THROTTLE ASSY. THROTTLE FOOT PEDAL ASSY. NO PART NO PART NAME 1 0937 NUT, HEX 10-32 3 2153 ROD END, 10-32 FEMALE RH 4 2203 WASHER, FLAT, #10 5 2203 WASHER, FLAT, #10 6 3513 SCREW, HHF 10-32 X 1 7 11710 SPACER, ENGINE THROTTLE 8 11771 BRACKET, ENGINE THROTTLE CABLE 9 0161 C WASHER, LOCK, 5/16 MED. 10 0730 SCREW, HHC 1/4-20 X 1 11 2124 CABLE, THROTTLE (RT) 12 22042 SPACER, THROTTLE SPRING 1.0 X.5 X3.0 13 2753 SPRING, THROTTLE RETURN, LOWER 14 2755 ADAPTOR, THROTTLE RET.
STR46SPVG — BATTERY ASSY. BATTERY ASSY. 13 5 15 11 12 CONNECT TO ENGINE (CHASSIS GROUND) 9 BLACK CABLE (NEGATIVE) STARTER 7 NEG (-) POS (+) 6 Y ER RED CABLE (POSITIVE) 8 TT BA 9 3 2 1 10 2 4 14 12 3 STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — BATTERY ASSY. BATTERY ASSY.
STR46SPVG — CONTROL PANEL ASSY. FRONT PANEL ASSY. STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
STR46SPVG — CONTROL PANEL ASSY. FRONT PANEL ASSY.
Effective: July 15, 2003 TERMS AND CONDITIONS OF SALE — PARTS Terms and Conditions of Sale STOW Construction Equipment PAYMENT TERMS Terms of payment for unit sales are 2% 15 days net 30 days from date of invoice unless otherwise specifically stated on our invoice. Parts invoices have terms of net 10 days. Minimum parts billing is $15.00 net. Applicable discounts will be computed on merchandise value only. Late charges will be assessed at prevailing rates.
NOTE PAGE STR46SPVG • RIDE-ON POWER TROWEL — OPERATION AND PARTS MANUAL — REV.
OPERATION AND PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 FAX: 800-672-7877 310-537-3700 FAX: 310-637-3284 SERVICE DEPARTMENT 800-478-1244 FAX: 310-537-4259 310-537-3700 TECHNICAL ASSISTANCE 800-478-1244 FAX: 310-631-5032 WARRANTY DEPARTMENT 800-421-1244, EXT. 279 FAX: 310-537-1173 310-537-3700, EXT. 279 SALES DEPARTMENT 310-661-4242 FAX: 310-604-9237 877-289-7869 (877-BUY-STOW) © COPYRIGHT 2007, MULTIQUIP INC.
