OPERATION AND PARTS MANUAL Diamond Back SP3 “STREET PRO” PROFESSIONAL SLAB SAW 35 HP WISCONSIN DIESEL ENGINE MODELS SP303516, SP303520, SP303526 SP303530 Revision #3 (09/29/06) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST COMPANY THE EQUIPMENT AT ALL TIMES.
MQ SP-3035 CONCRETE SAW PROPOSITION 65 WARNING MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 CONCRETE SAW SILICOSIS /RESPIRATORY HAZARDS WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks.
MQ SP-3035 CONCRETE SAW Table of Contents PROPOSITION 65 WARNING .......................................................................................1 SILICOSIS /RESPIRATORY HAZARDS......................................................................2 PARTS ORDERING PROCEDURES ........................................................................... 6 SAFETY..............................................................................................................................7 HAZARD SYMBOLS ..
MQ SP-3035 CONCRETE SAW MAINTENANCE.............................................................................................................40 REMOVABLE GUARDS AND ACCESS PANELS.................................................................. 40 BELTS AND PULLEYS ..................................................................................................... 41 BLADE FLANGE REMOVAL/INSTALLATION .................................................................... 45 CIRCUIT BREAKERS ...............
MQ SP-3035 CONCRETE SAW PULLEY AND V-BELT ASSY. ........................................................................................ 101 BATTERY ASSY............................................................................................................ 103 ENGINE BRACKETS ASSY............................................................................................. 105 ENGINE INSTALLATION ASSY.......................................................................................
www.multiquip.com MQ SP-3035 CONCRETE SAW PARTS ORDERING PROCEDURES Ordering parts has never been easier! Choose from three easy options: If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip.com.
MQ SP-3035 CONCRETE SAW SAFETY FOR YOUR SAFETY AND THE SAFETY OF OTHERS! NOTE This Owner's Manual has been developed to provide instructions for the safe and efficient operation of the Multiquip SP-3035 CONCRETE SAW. For engine maintenance information, please refer to the engine manufacturers’ instructions for data relative to its safe operation. Before using this CONCRETE SAW, ensure that the operating individual has read and understands all instructions in this manual.
MQ SP-3035 CONCRETE SAW HAZARD SYMBOLS Lethal Exhaust Gases Explosive Fuel Burn Hazards Engine exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. NEVER operate this equipment in a confined area or enclosed structure that does not provide ample free flow of air. Gasoline is extremely flammable, and its vapors can cause an explosion if ignited. DO NOT start the engine near spilled fuel or combustible fluids.
MQ SP-3035 CONCRETE SAW HAZARD SYMBOLS NEVER tamper with factory settings of engine governor or speed settings. Ensure the proper Speed Kits are installed to safely support the prescribed RPM settings for diamond blade operations. Over Speed Guards and Covers in Place NEVER operate the saw without blade guards and covers in place. Adhere to safety guidelines ANSI American National Standards Institute, OSHA, and/or other applicable local regulations. Rotating Blade can cut, tear, and crush.
MQ SP-3035 CONCRETE SAW HAZARD SYMBOLS Skin Injection NEVER use your hand to find hydraulic leaks. Use a piece of wood or cardboard. Hydraulic fluid injected into the skin must be treated by a knowledgeable physician immediately or severe injury or death can occur. Hazard NOTE Text set off like this presents clarifying information, specific instructions or commentary designed to help prevent damage to your saw, other property, or the environment.
MQ SP-3035 CONCRETE SAW General Safety Warnings Most accidents involving product operation, maintenance and repair are caused by failure to observe basic safety rules and precautions. Accidents can often be avoided by recognizing potentially hazardous situations before an incident occurs. WARNING Before operating the saw, make sure all protective guards are securely in place. All saws are supplied with a blade guard, collar guard and belt guard.
MQ SP-3035 CONCRETE SAW General Safety Warnings WARNING ALWAYS read, understand, and follow procedures in the Operator’s Manual before attempting to operate the equipment. Be sure the operator is familiar with proper safety precautions and operating techniques before using the saw. Make sure the operating area is clear before starting the engine. Maintain this equipment in a safe operating condition at all times Keep the saw clean.
MQ SP-3035 CONCRETE SAW BLADE SAFETY ALWAYS inspect diamond blades before each use. The blade should exhibit no cracks, dings, or flaws in the steel centered core and/or rim. Center (arbor) hole must be undamaged and true. Examine blade flanges for damage, excessive wear and cleanliness before mounting blade. Blade should fit snugly on the shaft and against the inside/outside of the saw. WARNING Only cut the material that is specified by the blade.
MQ SP-3035 CONCRETE SAW SAW TRANSPORTATION SAFETY WARNING Use appropriate lifting movement of the saw. equipment to ensure the safe DO NOT use the handle bars and/or front pointer as lifting points. NEVER attempt to tow the untrailered saw behind a vehicle. NEVER transport the saw with the blade mounted. EMERGENCIES WARNING ALWAYS know the location of the nearest fire extinguisher. ALWAYS know the location of the nearest first aid kit.
MQ SP-3035 CONCRETE SAW MACHINE OPERATION AND SAFETY DECALS The Multiquip SP-3035 Saw is equipped with a number of operation and safety decals. Should any of these decals become unreadable, replacements can be obtained from your dealer. WARNING To avoid injury, you MUST read and understand operator’s manual before using this machine. This machine to be operated by qualified personnel only. Ask for training as needed.
MQ SP-3035 CONCRETE SAW Serial Tag Fig. 2 — Serial Tag For future reference, fill in the model number and serial number of your saw in the space above. NOTE The serial tag contains the model number and serial number of the saw. This information details all parts that were included with the saw when it was shipped from the factory, as well as the date of manufacture. Record your ENGINE model number, spec. number and serial number here: MODEL NO. SPEC. NO. SERIAL NO.
MQ SP-3035 CONCRETE SAW OPERATION Before Starting Walk around the saw and ensure that all guards and panels are properly installed. Wear eye and hearing protection. Wear protective clothing. 1. Check engine and hydraulic oil. 2. Verify the proper-sized blade guard is fully installed on the blade guard mounting tab. 3. Adjust handlebars for best operator control. 4. If a belt driven water pump is installed, turn on the water flow before starting the engine.
MQ SP-3035 CONCRETE SAW Control Panel Voltmeter Engine Tach Auxiliary Switch Drive Light Switch Disengage Engine OnOff-Start Throttle Choke Depth Gauge Fuel Tank Cap Plunge Button Depth Zero Positraction Control Gauge Maintenance Information Operating Instructions Safety Warnings Water Pump Switch Water Flow Control Speed Control Joystick Fig. 5 — The Control Panel MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 CONCRETE SAW Engine Power, Cutting Power & Sheave Size NEVER tamper with factory settings of engine governor or speed settings. Ensure the proper Speed Kits are installed to safely support the prescribed RPM settings for diamond blade operations. WARNING Blade Size & Configuration per Model The SP-3035 is available in four Blade Speed configurations. The following chart shows the various configurations for each model.
MQ SP-3035 CONCRETE SAW Installing the Blade, Blade Guard & Blade Flange Remain Clear of all parts of saw while installing blade to prevent crush injury or death. Verify the engine start switch is OFF before installing blade. WARNING Tighten the 5/8” blade-mounting bolt to 100-125 footpounds torque. The blade can be mounted on either side of the saw to accommodate different cutting jobs. 1. 2. 3. 4. Raise the saw so that the blade will clear the ground when installed.
MQ SP-3035 CONCRETE SAW Removing the Blade, Blade Guard & Blade Flange Remain Clear of all parts of saw while installing blade to prevent crush injury or death. Verify the engine start switch is OFF before installing blade. WARNING Tighten the 5/8” blade-mounting bolt to 100-125 footpounds torque. 1. 2. 3. 4. Raise the saw so that the blade will clear the ground. Remove blade guard. See fig. 7 Remove the mounting bolt from the outer flange and bushing.
MQ SP-3035 CONCRETE SAW Stacking Blades for Wide Cuts Remain Clear of all parts of saw while installing blade to prevent crush injury or death. Verify the engine start switch is OFF before installing blade. WARNING Tighten the 5/8” blade-mounting bolt to 100-125 footpounds torque. Combining (stacking) blades to make wide cuts requires an optional Bushing Extension Kit. Kit #18502 allows blade stacking from .375” to .75” thickness. Kit #18501 allows blade stacking from .75” to 1.125” thickness. 1.
MQ SP-3035 CONCRETE SAW Installing and Removing the Blade Guard Blade Guards for the SP-3035 concrete saw can be installed on either side of the saw. Verify the engine start switch is OFF before installing blade. WARNING Remain clear of all parts of saw while installing blade to prevent crush injury or death. Installing the Blade Guard 1. 2. 3. 4. Ensure on/off key is off. See Fig. 5 or Fig. 15 Slide the Blade Guard Mounting Clip onto the Guard Mounting Tab on the frame.
MQ SP-3035 CONCRETE SAW Removing the Blade Guard During use, the Blade Guard can become tight on the tapered mounting tab. To loosen it, wiggle the Rear Blade Guard Handle up and down, while lifting with the Top Handle. Blade Guard Water Supply Verify that the water hose on the saw is connected to the Blade Guard and that the water pipes are pointed into both Blade Collars.
MQ SP-3035 CONCRETE SAW Installing the Flange Guard The Flange Guard provides protection from the Blade Flange not in use. 1. Verify that the unused Blade Flange is secured to the Spindle by tightening the mounting bolt. 2. Slide the Flange Guard onto the Guard Mounting Tab on the frame. Flange Guard Flange Fig. 11 — The Flange Guard, Installed MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 CONCRETE SAW Water Supply and Control To prevent damage to the impeller of a belt driven water pump, do not run the engine with the water pump switch on, unless the water supply is connected and water is flowing. WARNING When storing the saw during freezing weather, blow out the water lines to prevent damage to the water delivery system. Connect the job water hose to the water inlet fitting on the left side of the saw.
MQ SP-3035 CONCRETE SAW Handlebars The handlebars are adjustable to three different angles, for optimum operator control, and can also be slid fully inward for storage. Once handlebars are adjusted, lock them into position by tightening the lock knob on each side. Using the handlebars in position #2 or #3, when employing larger diameter blades reduces the need to bend over and the effort required by the operator to maneuver the unit. Lock Knob P3 P2 P1 Three operating positions Storage position Fig.
MQ SP-3035 CONCRETE SAW Fueling the Saw The 3000 Series saws feature a five-gallon clear molded plastic fuel tank with a sight gauge, central drain, and shutoff valve. The gas tank cap is located at the front of the saw. To prevent damage to the impeller of a belt driven water pump, do not run the engine with the water pump switch on, unless the water supply is connected and water is flowing.
MQ SP-3035 CONCRETE SAW Starting and Stopping the Engine WARNING Do not leave the saw unattended while the engine is running. Do not start, park, or leave the saw unattended on a slope. CAUTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. If the saw has an optional water pump, do not run the saw dry with the water pump switch ON — otherwise the pump impellers will be damaged.
MQ SP-3035 CONCRETE SAW Pointer Adjustment 1. Lower the front pointer assembly: Release the rope from the cam cleat, and rotate the pointer forward into position. 2. Adjust the pointer rod by loosening the lock knob: Once the pointer rod is set to the cut line, tighten the lock knob. 3. Adjust the rear pointer to the cut line: Loosen the lock bolt, position the pointer rod, and tighten the lock bolt. 4. To raise the front pointer assembly, pull back and up on the pointer cable. 5.
MQ SP-3035 CONCRETE SAW Raise – Lower Controls This saw uses a 12-volt hydraulic pump and cylinder to raise and lower the blade. Controls are located on the speed control joystick handle. Plunge Button Raise Button Fig. 17 — Joystick Handle 1. To plunge the blade, depress the button on the outer end of the handle. 2. To raise the blade, depress the button on the forward side of the handle. See the Maintenance section of this manual for a diagram of the Raise-Lower System components.
MQ SP-3035 CONCRETE SAW Setting the Depth Gauge & Depth Stop The 3000 Series saws use a cable-controlled Depth Gauge and mechanical Depth Stop to lock the blade at the desired cut depth. See Fig. 18. Setting the Depth Gauge 1. Lower the blade until it just touches the cutting surface. 2. Turn the Depth Gauge dial to zero. The Depth Gauge will show the depth of cut. It should not be necessary to readjust the Depth Indicator until a different diameter of blade is installed. Setting the Depth Stop 1.
MQ SP-3035 CONCRETE SAW Drive System The 3000 Series saws have a cable-controlled Hydro-Gear hydrostatic powered transaxle with fully adjustable F-N-R (Forward-Neutral-Reverse) speed adjustment via a joystick control handle. The system utilizes a remote oil filter. There are no chains, sprockets or gearboxes requiring daily service. The 3000 Series saws can travel at speeds up to 250 feet per minute. Transaxle Oil Filter Positraction Engagement Lever Transaxle Positraction Bar Fig.
MQ SP-3035 CONCRETE SAW Drive System Controls The control handle controls FORWARD-NEUTRAL-REVERSE (F-N-R) speeds and the raising and lowering of the saw. To increase forward speed, slowly move the joystick FORWARD. Pulling the joystick backward decreases saw speed, and when the joystick passes NEUTRAL the saw moves into REVERSE. Reverse speed is also controlled by the position of the joystick.
MQ SP-3035 CONCRETE SAW Positraction Positraction, when ON, locks both drive wheels together for straight-line movement. It is recommended for all cutting and is especially helpful on uneven surfaces, and when loading and unloading the saw. 1. Move the Positraction lever to “ON” (positraction engaged) to lock both drive wheels. 2. To unlock the drive wheels for easy maneuverability and turning, move the Positraction lever to OFF.
MQ SP-3035 CONCRETE SAW Transaxle The hydrostatic-powered transaxle has no chains, sprockets or gearboxes to service. There is a simple cable control for forward-reverse motion, and a single drive belt from the engine to power the transaxle. Fig. 22 —Transaxle Night Light The optional night light can be used on either side of the saw, and can be extended and rotated for best illumination of the cutting area. Once the light is aimed, lock it in position by tightening the lock knob.
MQ SP-3035 CONCRETE SAW Transportation Tie-downs and Lift Point Tie-downs The saw is provided with holes at each corner of the lower frame for easy tie-down during transportation. The saw MUST be tied down whenever it is being transported. Tie-down Tie-down Fig. 24 —Tie-down Points Lift Point The convenient single point for raising the saw with a hoist is located on top of the engine. Lift Point Fig. 25 — Lift Point WARNING To avoid possible injury, stay clear of the saw while it is being hoisted.
MQ SP-3035 CONCRETE SAW Operation on a Slope or Incline Never operate, cut, or face the saw down a slope or incline. The weight of the saw will shift to the front wheels allowing the rear wheels to skid or come completely off the ground. This allows the saw to free wheel and possibly cause a runaway condition. Always remove the blade when transporting or moving the saw outside of the cutting area. Use the following procedures for loading and unloading the saw.
MQ SP-3035 CONCRETE SAW If an attempt is made to start the saw with the blade pinched, the starter will suffer damage. If an attempt is made to use the lift pump to raise the saw to free the blade, the lift motor and front axle could be damaged. If an attempt is made to lift the saw and blade out of the cut utilizing equipment such as a loader or back hoe, the saw frame and axle are likely to be damaged.
MQ SP-3035 CONCRETE SAW MAINTENANCE This saw has many service-saving features, such as fully enclosed oil bath lubricated Spindle bearings, which require no daily lubrication. Level the saw frame surface prior to service in order to get accurate oil level readings.
MQ SP-3035 CONCRETE SAW Belts and Pulleys Belt Qty Part Number Spindle Drive Belt (POWERBAND) 1 520006 Transaxle Drive Belt 1 521005 Engine to Jack shaft Drive Belt 1 521005 Spindle (Blade Shaft) Drive Belt TransAxle Drive Belt Fig. 27 — Belt Locations Engine to Jack Shaft Drive Belt V-Belt Tension The ideal V-Belt tension is the lowest tension at which the belt will not slip under peak load conditions. Check V-Belt tension frequently during the first 24-48 hours of run-in operation.
MQ SP-3035 CONCRETE SAW Spindle (Blade Shaft) Drive Belt Tension Adjustment NOTE When loosening drive belts, lower the saw to reduce stress on the tensioning system, and use gravity to pull the engine forward slightly. When tightening belts, raise the saw, and gravity will aid the process also. NEVER attempt to check or adjust the V-belt tension with the engine running. Severe injury can occur. Keep fingers, hands, hair, and clothing away from all moving parts. WARNING 1.
MQ SP-3035 CONCRETE SAW 4. Loosen the Outer Jam Nut on the Single Point Belt Tension Bolt. Turn the Inner Jam Nut counter-clockwise. 5. Adjust drive belt to desired tension. Do Not over tighten. 6. Tighten Engine Mount Lock Bolts. 7. Tighten the Jam Nuts to prevent the Single-Point Bolt from turning. Inner Jam Nut Engine Mount Lock Bolt (1 of 2) Outer Jam Nut Spindle Belt Upper Belt Guard Bolt Lower Belt Guard Bolts Lower Belt Guard Single-Point Belt Tension Bolt Fig.
MQ SP-3035 CONCRETE SAW Replacing the Jack Shaft Belt WARNING 1. 2. 3. 4. 5. 6. NEVER attempt to check or adjust the V-belt tension with the engine running. Severe injury can occur. Keep fingers, hands, hair, and clothing away from all moving parts. Remove the Belt Guards (see Figs. 26 & 29). Loosen the Rotary Tensioner. Remove the Spindle Belt (see above). Remove and replace the Jack Shaft Belt. Replace the Spindle Belt (see above). Adjust the Rotary Tensioner.
MQ SP-3035 CONCRETE SAW Blade Flange Removal/Installation Correct removal or installation of the Inner Blade Flange or Flange requires a Flange Puller (option Part Number 18503) as shown below. Follow instructions closely to prevent injury from flying Blade Flanges! WARNING Because of tapered fit between Blade Flange and Spindle, 5-10 tons of force is needed to release the inner flange. Parts and tools can become dangerous projectiles if instructions are not followed properly.
MQ SP-3035 CONCRETE SAW Ensure the Outer Flange is in place to prevent the Puller and Inner Flange from flying off when the taper breaks loose, and causing injury! DANGER NOTE If the Inner Flange does not readily come free from the tapered Spindle, lightly tap on the central Puller bolt. This should cause the flange to break free from the shaft. Installing the Inner Blade Flange 1.
MQ SP-3035 CONCRETE SAW 6. Loosen the Mounting Bolt and remove the Outer Flange and Bushing. 7. Inspect the Inner Flange to ensure the proper seating of the tapered fit. The Inner Flange should be seated between .030” and 0.0” (flush) to the end of the Spindle. Fig. 33 — Proper seating of the Inner Flange and Spindle 8. Test to ensure that the Inner Flange does not wobble when rotated. Use a dial indicator on the face of the Flange. Maximum tolerance is .003” run-out on the face of the Flange.
MQ SP-3035 CONCRETE SAW Spindle Replacement To assure correct Spindle/Wheel alignment it is recommended that this operation be performed by a Multiquip Authorized Service Center. DO NOT unbolt the Spindle Mounting Blocks, as they have been factory installed for correct Spindle/wheel alignment. NOTE 1. Remove the Spindle Drive Belts (see Replacing the Spindle Belt, above). 2. Tighten the Engine Mount Lock Bolts to prevent engine movement during step #3.
MQ SP-3035 CONCRETE SAW Spindle Mounting Block DO NOT REMOVE Spindle Mounting Block DO NOT REMOVE Saddle Clamps Lower Belt Protector Fig. 35 — Spindle Replacement 7. Remove the Spindle. DO NOT unbolt the Spindle Mounting Blocks, as they have been factory-installed for correct Spindle/wheel alignment. 8. Fill the new Spindle with approved hydraulic oil and cap. 9. Perform Steps 1-5 in reverse order. Spacing Spacing Fig.
MQ SP-3035 CONCRETE SAW Circuit Breakers Three thermal circuit breakers are located behind the Control Panel access cover. Remove Dash Panel to access circuit breakers Fig. 37 — Circuit Breaker location Under normal circumstance circuit breakers do not require service; they are automatically re-set once an overload condition has been corrected. If one or more breakers are cycling on/off, locate the cause of the electrical overload and repair as required. Also see the Electrical Schematic on page 61.
MQ SP-3035 CONCRETE SAW Lubrication This saw has six grease fittings. Locations are shown in Figure 38 on the front axle assembly, and one, (not shown) on the Jackshaft assembly. Front axle pivot bearings (2) Hydraulic lift cylinder end (1) Depth cylinder pivot bracket (2) Jackshaft pivot (1) These fittings are easily accessed by raising the saw half way up, and then lifting the rear of the saw until the blade flanges rest on the ground.
MQ SP-3035 CONCRETE SAW Engine Maintenance The Model SP-3035 uses a 35 HP Wisconsin engine. See the engine manual for service details. Check air filters daily. Do not clean. Replace as needed. See Caution below. Check engine oil level daily. Level the saw frame prior to service to get accurate readings. Change the engine oil and filter every 50 hours of operation.
MQ SP-3035 CONCRETE SAW Raise-Lower System This saw uses a 12-volt hydraulic pump and cylinder to power the raise-lower system. Level the frame prior to service to get accurate readings. Check oil level daily. Fill the reservoir half full when cold. Use 5W-30 premium grade engine oil. Raise-Lower Pump Raise-Lower Reservoir Hydraulic Manifold Raise-Lower Cylinder Fig. 40 — Raise-Lower System MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 CONCRETE SAW Control Handle Adjustment The Control Handle is adjustable to provide the preferred “feel”. 1. Using a ¼” Allen wrench and 9/16” wrench, loosen both pivot bolts until they can be turned by hand. Pivot #1 requires only a 9/16” wrench, as the Allen nut side is welded in place. 2. Tighten pivot #1 until the handle is close to the desired “feel”. 3. Tighten pivot #2 until it just starts to increase the force required to move the handle. Pivot #1 Pivot #2 Fig.
MQ SP-3035 CONCRETE SAW Hydraulic System The hydraulic system consists of: Spindle Assembly (1) Transaxle Assembly (9) Lift Cylinder (5) Hydraulic Drive and Spindle Oil Reservoir (7) Hydraulic Pump (2) Hydraulic Manifold (4) Oil Filters (3, 6) Lift Cylinder Reservoir (8) Routine Maintenance Check oil level daily. Fill the reservoir to the fill line when cold. Level frame prior to service to get an accurate reading. Use 5W-30 premium grade engine oil.
MQ SP-3035 CONCRETE SAW Draining & Filling the Hydraulic System To drain the Transaxle 1. Remove the drain plug from the bottom of the Spindle housing and the bottom of the Transaxle. Drain Plug Fig. 43 — Transaxle Drain Plug NOTE 2. 3. 4. 5. Collect and dispose of the used oil and oil filter in an environmentally friendly manner. Do not drain onto the ground or pour used oil down drains. Remove the old oil filter. See Fig. 43, above. Once drained, reinstall the drain plugs.
MQ SP-3035 CONCRETE SAW To Remote Fill Reservoir Drain Fig. 44 — Spindle Assembly 1. Raise the saw 2/3 or more up. 2. Remove the drain plug from the bottom of the Spindle housing. 3. Re-install the drain plug and install a new oil filter. CAUTION To prevent damage to the hydraulic pump, pre-fill the new oil filter prior to installation. To refill the hydraulic system 1. Ensure the saw is fully lowered if it had been raised. 2. Add hydraulic oil to the Drive & Spindle System Reservoir.
MQ SP-3035 CONCRETE SAW Drive Wheel Alignment Below is the suggested technique for aligning the wheels. Distance X is the same on either side; the Front Axle and Spindle must be at right angles to the frame edge. Distance A is 3/16” (.187”) longer on the right side, so that the saw steers slightly left. Users may wish to alter the alignment to fit a particular application. Fig. 45 — Drive Wheel Alignment MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 CONCRETE SAW The drive wheels are aligned by adjusting the entire rear drive assembly. 1. Raise the saw halfway, then lift the rear of the saw until flanges touch the ground. Use suitable supports to prevent tipping or shifting of weight. 2. Loosen the adjustment-side attachment bolts until washers spin freely. 3. Loosen pivot-side bolts enough to move the adjustment-side wheel in the appropriate direction to achieve the desired alignment distance. 4.
MQ SP-3035 CONCRETE SAW Positraction Adjustment Clamp Position (Inner Lip of Drive Hub) Clamp Position (Inside Wheel Lip) Clamp Plate Bolt Clamp Plate Bolt Spacer Position Fig. 47 — Positraction Adjustment Bolt Locations 1. Lift Saw 4” to 6” and tilt forward to place spindle flanges on ground. When flanges are on the ground, depress Raise Button to raise the rear of the saw to full height. Use suitable stands to hold rear of saw up. 2. Disengage Positraction Lever fully. 3.
MQ SP-3035 CONCRETE SAW EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availibility of the parts listed.
MQ SP-3035 CONCRETE SAW SUGGESTED SPARE PARTS MQ SP-3035 CONCRETE SAW WITH WISCONSIN 35 HP AIR-COOLED DIESEL ENGINE 1 to 3 Units Qty. P/N Description 1..........300000-1...........FILTER, AIR, ELEMENT, PRIMARY 1..........300000-2...........FILTER, AIR ELEMENT, SAFETLY 1..........306004 ..............FILTER, OIL, WISCONSIN 35 HP 1..........306006 ..............FILTER, TRANSAXLE 1..........304000 ..............FILTER, FUEL, WISCONSIN 35 HP 1..........520006 ..............V-BELT, 6 3VX425 (GOODYEAR) 1........
MQ SP-3035 Concrete Saw — Nameplate and Decals COMPONENT DRAWINGS Nameplate and Decals Assy. The Multiquip SP-3035 Saw is equipped with a number of operation and safety decals. Should any of these decals become unreadable, replacements can be obtained from your dealer. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Nameplate and Decals Nameplate and Decals Assy.
MQ SP-3035 Concrete Saw — Deck/Gauge Panel Assy. Deck/Gauge Panel Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Deck/Gauge Panel Assy. Deck/Gauge Panel Assy. NO 1 2 PART NO M600020 M600019 PART NAME GAUGE PANEL DECK PANEL QTY. 1 1 REMARKS MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Console/Sheet Metal Assy. Console/Sheet Metal Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Console/Sheet Metal Assy. Console/Sheet Metal Assy. NO 1# 2# 3# 8 18 19 22 25 26 28# 29# 30 31 32 PART NO 0166 933242 204007 25796 0655 25865 25805 3214 933244 15503 584011 923114 35180 13287 PART NAME QTY.
MQ SP-3035 Concrete Saw — Access Panel Assy. Access Panel Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Access Panel Assy. Access Panel Assy. NO 1# 2# 3# 4# 5# 6# 7# 8 PART NO 25795 29057 560020 577002 12287 10024 10930 25794 PART NAME QTY. REMARK PANEL, REAR CONSOLE, RED 1 DOCUMENT BOX, CP90007-07 1 LATCH, REAR SAW ACCESS PANEL 2 WEATHER STRIP, REAR SAW ACCESS PANEL 1.75 FT. SCREW, THP 1/4-20 X 3/4" SS 4 NUT, NYLOCK 1/4-20 4 WASHER, FENDER, 1/4 X 1-1/4" 4 PANEL ASSY., REAR CONSOLE, RED ........................ 1..................
MQ SP-3035 Concrete Saw — Fuel Tank Assy. Fuel Tank Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Fuel Tank Assy. Fuel Tank Assy. NO 1# 2# 3# 4# 5# 6# 7# 8# 9# 10# 11# 12# 13 14 15 16 PART NO 1400003 29509 19633 446005 19473 35022 35059 2295 304000 35060 370626 367216 25831 25801 933242 4196 PART NAME QTY. REMARK TANK, FUEL 1 CAP, FUEL TANK 2.25" DIA. ONE WAY VALVE 1 BUSHING, RUBBER FUEL DAPCO 10672 1 VALVE, FUEL ON/OFF 1/4" 1 CLAMP, HOSE WORM #2 4 CLAMP, LOOP CUSHIONED #8 1 HOSE, FUEL .250 ID, 12" 1 SCREW, HHC 1/4-20 X 7/8" 1 FILTER, FUEL, WISCONSIN 1 HOSE, FUEL .
MQ SP-3035 Concrete Saw — F-N-R Control Handle Assy. F-N-R Control Handle Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — F-N-R Control Handle Assy. F-N-R Control Handle Assy. NO 1 2# 3# 4# 5# 6# 7# 8# 9# 10# 11 12% 13% 14% 15% 16% 17% 18% 19% 20% 21% 22% 23% 24% 25% PART NO 560030 560028-6 5600028-8 560028-4 560028-3 560028-5 560028-1 60118 925381 560028-2 35176 25627 405070 405046 12223 6904 580001 440006 120077 565006 915003 584044 2295 440005 933240 PART NAME QTY. REMARK F-N-R CONTROL HANDLE ASSY. ...................... 1 .......................
MQ SP-3035 Concrete Saw — Joystick Mounting Assy.MQ SP-3035 CONCRETE SAW — Joystick Mounting Assy. 25 11 7 5 4 6 13 21 23 2 16 20 20 24 1 20 24 3 22 10 9 19 1 15 12 8 17 18 14 26 MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Joystick Mounting Assy.MQ SP-3035 CONCRETE SAW — Joystick Mounting Assy. NO 1# 2# 3# 4# 5# 6# 7# 8# 9# 10# 11# 12# 13# 14# 15# 16# 17# 18# 19# 20# 21# 22# 23# 24# 25# 26 PART NO 0161D 10019 1579 2203 405053 442005-6 442006-3 442011 442012 442013 442021 442022 460018 565005 584021 584023 584024 926348 933015 933073 933225 933240 933242 938062 973735 35122 PART NAME QTY. REMARK NUT, HEX FINISH 5/16-18 2 NUT, FYLOC #10-32 1 SCREW. JJC 1/4-20 X .
MQ SP-3035 Concrete Saw — Lift Pump Circuit Assy. Lift Pump Circuit Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Lift Pump Circuit Assy. Lift Pump Circuit Assy. NO 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 23 24 25 26 27 28 PART NO 340011 169003 447007 21159 368817 35149 366640 35157 35156 35250 366437 35248 570050 35057 0655 933241 933240 20909 0949 480003 2621 446009 400000 923000 933076 PART NAME PUMP, LIFT PIN, CYLINDER CYLINDER, LIFT FITTING, 45 4MJ-4MO FITTING, 90 4MJ-4MO FITTING, ORIFICE 4MJ-4MO FITTING, 90 4MJ-4FJ FITTING, TEE 4MO-4MJ HOSE ASM, 11.3" HOSE ASM, 10.
MQ SP-3035 Concrete Saw — Water System Assy. Water System Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Water System Assy. Water System Assy. NO 1 2 3 4 5 6 7 PART NO 446004 35047 35052 25059 25931 26496 25827 PART NAME VALVE, BALL, 1/2 BRASS HOSE ASM, 95.1" #8LP HOSE, 1/2 ID PUSHLOCK 250 PSI, 8" FITTING, BRASS 8 PUSH-ON 1/2 MP FITTING, 90 8 BARB - 1/2 MP FITTING, 90 1/2 MP - 1/2 FP FITTING, BRASS (F) 3/4 GHT SWIVEL 1/2 MNPT QTY. 1 1 1 1 2 1 1 REMARK MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Depth Indicator Assy. Depth Indicator Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Depth Indicator Assy. Depth Indicator Assy. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 PART NO 125032 110031 560025 460019 973752 584025 10024 926149 1618 933240 540011 583059 440012 120243 0131 A 1579 565004 160013 923116 13287 PART NAME DEPTH INDICATOR U-BRACKET POINTER, DEPTH KNOB, COMFORT GRIP FLANGE BEARING, .
MQ SP-3035 Concrete Saw — Handle and Light Assy. Handle and Light Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Handle and Light Assy. Handle and Light Assy. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. 12387 120206 405001 0161 C 0161 D 560023-1 560024 923199 574002 35359 405002 2532 560017 0655 933241 120244 PART NAME NUT, NYLOCK 8X32 LIGHT BAR, CONCRETE SAW CONNECTOR, PLUG, 4 PIN FEMALE WASHER, LOCK 5/16" NUT, 5/16-18 HANDLE BAR, CONCRETE SAW KNOB, HANDLEBAR SCREW, SHC 8-32 X 1-1/4 CAM CLEAT TERMINAL,FEM-SMALL 16-18 GA CORD, LIGHT-EXTENDABLE LIGHT ASSY., RECTANGULAR COMP.
MQ SP-3035 Concrete Saw — Front/Rear Pointer Assy. Front/Rear Pointer Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Front/Rear Pointer Assy. Front/Rear Pointer Assy. NO 1# 2# 3# 4# 5# 6# 7# 8# 9# 10# 11# 12# 13# 14# 15# 16# 17# 18# 19 20 21 PART NO 120045 120046 25832 110044 15503 500005 160004 582008 966166 965105 933241 0202 926006 1493 10133 1456 3233 933244 M10005 110020 0205 PART NAME QTY. REMARK RIGHT SIDE POINTER 1 LEFT SIDE POINTER 1 ROPE ASSY.
MQ SP-3035 Concrete Saw — Gauges and Controls Assy. Gauges and Controls Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Gauges and Controls Assy. Gauges and Controls Assy. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PART NO 15171 446004 25627 560025 574002 15481 120210 TBD 25634 TBD TBD 15171 584028 926327 25634 933242 5283 35174 406001 423000 421000 406000 35125 406012 933241 923201 406019 25935 PART NAME QTY. REMARK CABLE PULL 1 VALVE, WATER FLOW CONTROL 1 F-N-R CONTROL ASSY.
MQ SP-3035 Concrete Saw — Front Axle Assy. Front Axle Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Front Axle Assy. Front Axle Assy. NO 8 9 10 11 12 13 14 15 16 17# 18# 19# 20# 21# 22 23 24 25 PART NO 913161 933243 100005 460006 16677 2621 926064 16010-1 25839 485002 500003 460002 M508006 576003 933246 06505-008 508005 1579 PART NAME QTY. REMARK SCREW, HHC 7/16-14 X 2 4 WASHER, FLAT SAE 7/16 8 BEARING BACKING PLATE 2 BEARING, FLANGED, 1" 2 NUT, LOCK NUT, NYLOC 7/16 4 FITTING, GREASE ZERK STR 2 SCREW, SQHS, CP 2 FRONT AXLE 1 FRONT WHEEL ASSEMBLY...................2.............
MQ SP-3035 Concrete Saw — Depth Stop Assy. Depth Stop Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Depth Stop Assy. Depth Stop Assy. NO 1 2 3 4 5 6 7 PART NO 35120 933244 565002 582009 442014 19974 965103 PART NAME DEPTH STOP LEAD SCREW WASHER, FLAT SAE 1/2 SPRING, COMPRESSION, 7/8 COLLAR, SET .50 ID DEPTH STOP LINKAGE PIN, CLEVIS 1/2 X 1.25 EFFECT PIN, COTTER 5/32 X 1 PLTD QTY. 1 3 1 1 1 1 1 REMARK MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Platform Assy. Platform Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Platform Assy. Platform Assy. NO 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO 25807 924287 120038 120040 3214 933244 583092 25837 25820 120092 M200000 5283 926327 448002 933242 PART NAME PLATFORM SCREW, FHSC, 3/8-16 X 1-1/4,NP CLIP, MOUNT,BLADEGUARD SPACER, BLADEGUARD CLIP, .
MQ SP-3035 Concrete Saw — Drive Assy. Drive Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Drive Assy. Drive Assy. NO 1 2 3 4 5 6 7 8 9 10 11# 12 13% 14 15 16% 17# 18# 19# 20# 21# 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 PART NO 263002 35325 582038 206005 35190 120078 540033 06500-020 933241 5283 933242 1493 BDU-10L-122 25495 0202 35151 933201 933072 923118 583064 384001 25623 35019 370192 370162-1 368699 35054 25976 35226 35050 35051 366692 570053 35049 35048 120260 25617 306006 144003 367470 923200 933076 923201 11780 PART NAME QTY.
MQ SP-3035 Concrete Saw — Bladeshaft and Mounting Assy. Bladeshaft and Mounting Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Bladeshaft and Mounting Assy. Bladeshaft and Mounting Assy. NO. 1 2# 4# 5# 6# 7# 8# 9# 10# 11#% 12#% 13#% 14#% 15#% 16#% 17#% 18#% 19#% 20#% 21#% 22#% 23#% 24#% 25#% 26#% 27#% 28#% 29#% 30#% 31#% 32#% 33#% 34#% 35#%+ 36#%+ 37#%+ 38#%+ 39#%+@ 40#%+@ PART NO.
MQ SP-3035 Concrete Saw — Positraction Assy. Positraction Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Positraction Assy. Positraction Assy.
MQ SP-3035 Concrete Saw — Pulley and V-Belt Assy. Pulley and V-Belt Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Pulley and V-Belt Assy. Pulley and V-Belt Assy. NO PART NO PART NAME 1 1 1 1 2 2 2 3 4 5 5 6 7 8 9@ 10@ 11@ 12@ 13@ 14@ 15 16$ 17$ 18$ 19$ 20$ 21$ 22$ 23$ 24$ 25$ 26$ 27 28 29 540006 540066 540065 540049 540000 540070 540012 582013 582028 582020 460030 520006 521005 25557 3214 933244 448000 544001 540003 25716 13016 540030 925437 576003 460021 25845 584013 167001 10307 933244 960102 10176 120081 0205 PULLEY, BLADESHAFT 3.8 6G 3VX1615 .............1..........
MQ SP-3035 Concrete Saw — Battery Assy. Battery Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Battery Assy. Battery Assy. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO 404000 25838 19303 TBD 16782 TBD 12022 933242 933240 10133 10024 35023 1023 12278 TBD PART NAME BATTERY, GROUP 26R MOUNT, BATTERY CLAMP CABLE, BATTERY POS 4 GA X 48" POST CABLE, BATTERY POS CABLE, 24" POS CABLE, BATTERY NEG CABLE, BATTERY NEG 4 GA X 20" X 1/2" WASHER, FLAT SAE 3/8 GRD 9 YZ WASHER, FLAT SAE 1/4 GRD 9 YZ NUT, NYLOC 3/8-16 NUT, NYLOC 1/4-20 CLAMP, LOOM CUSHIONED #10 .
MQ SP-3035 Concrete Saw — Engine Brackets Assy. Engine Brackets Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Engine Brackets Assy. Engine Brackets Assy. NO 1 2 3 4 5# 6# 7# 8# 12# 13# 14# 15# 16 17 20 21# 22# 24 PART NO 125034 933242 915105 125016-3 282002 300000 300000-1 300000-2 364002 10434 364003 364000 280000 2534 25719 35098 962015 35182 PART NAME QTY. REMARK LIFTING RING 1 WASHER, FLAT SAE 3/8 GRD 9 YZ 4 SCREW, HHC 3/8-16 X 1.
MQ SP-3035 Concrete Saw — Engine Installation Assy. Engine Installation Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Engine Installation Assy. Engine Installation Assy. NO 1 2 3 4 5 6 7 8 9 10 PART NO 15500 25813 120079 933246 4702 06503-026 25836 913217 933244 10176 PART NAME ENGINE, WISCONSIN W41770-467438R MOUNT, JACKSHAFT PIVOT ARM MOUNT, MOTOR TENSIONER WASHER, FLAT SAE 5/8 GRD 9 YZ NUT, HEX FINISH 5/8-11 SCREW, HHC 1/2-13 X 3-1/4 MOUNT, ENGINE TENSIONING SCREW, HHC 1/2-13 X 3 1/2 GR5 WZ WASHER, FLAT SAE 1/2 GRD 9 YZ NUT, NYLOC 1/2-13 QTY.
MQ SP-3035 Concrete Saw — Bladeguard Assy. Bladeguard Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Bladeguard Assy. Bladeguard Assy. NO 1 1 1 1 2 3 3 4 5 6 7 9 10 11 12 13 13 14 15 16 17 18 19 19 20 PART NO M18100 M18140 M18180 M18220 10176 582040 582039 362000 923144 362003 1618 933209 10024 200019 0131 A 445002 445003 5277 36002 320010 2113 370455 06503-026 06503-030 320009 PART NAME QTY. REMARK BLADE GUARD 16-INCH 1 BLADE GUARD 20-INCH 1 BLADE GUARD 26-INCH 1 BLADE GUARD 30-INCH 1 NUT, NYLOCK 1 BUSHING, BLADE GUARD 1 BUSHING, BLADE GUARD.....................................
MQ SP-3035 Concrete Saw — Optional Water Pump Kit Assy. Optional Water Pump Kit Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Optional Water Pump Kit Assy. Optional Water Pump Kit Assy. NO 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO M18100 120084 120085 342000 933242 933244 205 16524 369970 366057 366956 25932 25931 540032 521005 35257 35258 406000 PART NAME BLADE GUARD 16-INCH DESCRIPTION MOUNT, WATER PUMP PUMP, WATER JABSCO WASHER, FLAT SAE 3/8 GRD 9 YZ WASHER, FLAT SAE 1/2 GRD 9 YZ SCREW, HHC 3/8-16 X 1.
MQ SP-3035 Concrete Saw — Collar Puller Assy. Collar Puller Assy. MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Collar Puller Assy. Collar Puller Assy. NO 1# 2# 3# 4# 5# 6 PART NO 584037 584038 2549 25138 18503-I 18503 PART NAME QTY. REMARK OUTER PULLER 1 PLATE, PULLER 1 SCREW, HHC 1/2-13 X 3 3 SCREW, HHC 5/8-11 X 5 TAP 1 COLLAR PULLER INSTRUCTION SHEET 1 COLLAR PULLER ..................................................... 1.................. INCLUDES ITEMS W/# MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Seal Sleeve Puller Seal/Seal Installation Tool Seal Sleeve Puller/Seal Installation Tool MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Seal Sleeve Puller Seal/Seal Installation Tool Seal Sleeve Puller/Seal Installation Tool NO 1# 2 3# 4# 5# 6# 7# 8# 9# PART NO 35163 M18505 35162 584052 35161 937980 35164 35165 584050 PART NAME QTY. REMARK SCREW, HHC 3/8 – 16 X 4 FULL THREAD 1 SEAL SLEEVE & THRUST WASHER PULLER ASM ....... 1 ..............
MQ SP-3035 Concrete Saw — Bushing Extension Kits Bushing Extension Kits MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Bushing Extension Kits Bushing Extension Kits BUSHING EXTENSION KIT 18501 (.375 — .75) NO PART NO PART NAME 1 926949 DOWEL PIN, 3/8 X 2-1/4 2 180003-1 OUTER COLLAR 582032 QD BUSHING 3/8 TO 3/4 3 4 90123445 5/8-11X 4 LH HEX BOLT 5 915319 5/8-11X 4 RH HEX BOLT QTY. 1 1 1 1 1 REMARK BUSHING EXTENSION KIT 18502 (.75 — 1.
MQ SP-3035 Concrete Saw — Electric Schematic ELECTRIC SCHEMATIC MQ SP-3035 CONCRETE SAW — OPERATION AND PARTS MANUAL — REV.
MQ SP-3035 Concrete Saw — Specifications SPECIFICATIONS Engine Precleaner Air Cleaner Fuel Tank Spindle Drive Belt Belt Tensioners Blade Range Max Cut Depth Blade Guard Spindle Assembly Wisconsin 35 hp V-4, electronic ignition, remote oil filter and above-frame remote oil drain Centrifugal type, self-cleaning Four-stage air filtration, cartridge element w/ safety element 5 gallon molded tank, shutoff valve and central drain Single 6-groove premium quality 3V Cross-Section Powerband Single-point Spindle be
OPERATION AND PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office 18910 Wilmington Ave. Carson, CA 90746 Contact: mq@multiquip.com Mayco Parts 800-306-2926 310-537-3700 Service Department 800-421-1244 310-537-3700 Tel.
