user manual

ManualsBrandsMultiquip ManualsSeptic SystemSeptic System ST-2005

OPERATION AND PARTS MANUAL

Revision #3 (09/21/04)

Submersible Pumps

Model ST-2005 Series

THIS MANUAL MUST ACCOMPANY

THE EQUIPMENT AT ALL TIMES.

Summary of content (44 pages)

PAGE 1
OPERATION AND PARTS MANUAL Submersible Pumps Model ST-2005 Series Revision #3 (09/21/04) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PAGE 2
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING MULTIQUIP CORPORATE OFFICE 18910 Wilmington Ave. Carson, CA 90746 Email: mq@multiquip.com Internet: www.multiquip.com PARTS DEPARTMENT 800-427-1244 310-537-3700 MAYCO PARTS 800-306-2926 310-537-3700 SERVICE DEPARTMENT 800-421-1244 310-537-3700 TECHNICAL ASSISTANCE 800-478-1244 WARRANTY DEPARTMENT 800-421-1244, EXT. 279 310-537-3700, EXT.
PAGE 3
ST-2005 SERIES SUB. PUMP — TABLE OF CONTENTS Multiquip ST-2005 Series Submersible Pumps Submersible Pump Component Drawings Here's How To Get Help ............................................ 2 Table Of Contents ..................................................... 3 Parts Ordering Procedures ....................................... 4 Safety Message Alert Symbols ................................. 5 Rules For Safe Operation ...................................... 6-7 Dimensions ..............................
PAGE 4
ST-2005 SERIES SUB.
PAGE 5
ST-2005 SERIES SUB. PUMP — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. NOTE This Owner's Manual has been developed to provide complete instructions for the safe and efficient operation of the Multiquip Model ST2005 Series Submersible Pumps.
PAGE 6
ST-2005 SERIES SUB. PUMP — RULES FOR SAFE OPERATION CAUTION Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the ST- 2005 Series Submersible Pumps: GENERAL SAFETY ■ DO NOT operate or servicing this equipment before reading this entire manual.
PAGE 7
ST-2005 SERIES SUB. PUMP ■ ALWAYS make sure that electrical circuits are properly grounded per the National Electrical Code (NEC) and local codes before operating pump. Severe injury or death by electrocution can result from operating an ungrounded pump. — RULES FOR SAFE OPERATION . Emergencies ■ ALWAYS know the location of the nearest fire extinguisher. ■ NEVER use this pump to remove water from a swimming pool when people are in the water.
PAGE 8
ST-2005 SERIES SUB. PUMP — DIMENSIONS Figure 1. ST-2005T Dimensions PAGE 8 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 9
ST-2005 SERIES SUB. PUMP — SPECIFICATIONS TABLE 1. SPECIFICATIONS Model ST-2005T ST-2005C ST-2005S ST-2005CUL ST-2005TCUL Type Submersible Trash Pump Centrifugal Submersible Pump Centrifugal Submersible Pump Centrifugal Submersible Pump Submersible Trash Pump Impeller Cast Iron Ductile Cast Iron Ductile Stainless Steel Cast Iron Ductile Suction & Discharge Size 2.00 in. (51 mm) 2.00 in.
PAGE 10
ST-2005 SERIES SUB. PUMP — GENERAL INFORMATION Introduction The Multiquip Model ST-2005 series submersible pumps are designed to pump water and is used for the draining (dewatering) of swimming pools, well casings construction sites, cofferdams, manholes, transformer vaults and excavations. A cast iron ductile type impeller is attached to the output shaft of a 0.5 HP electric motor which provides adequate power for general purpose pumping.
PAGE 11
ST-2005 SERIES SUB. PUMP — COMPONENTS Figure 2. Submersible Pump Components Figures 2 shows the location of the basic components, for the ST-2005 series submersible pumps. Listed below is a brief explanation of each component. 1. Strainer Base – This strainer base is made of stainless steel which is resistant to hardware corrosion. DO NOT pump large objects or debris with this pump. This pump is for pumping water only. For de-watering purposes, always place the strainer base on a platform. 2.
PAGE 12
ST-2005 SERIES SUB. PUMP — FLOAT SWITCHES Float Switch Theory Design Features Mercury monitoring is a mercury-switch actuated, liquid level control that has proven to be more economical and longer lasting than other types of liquid-level control systems, easily replacing and improving upon diaphram switches, air bubble systems and electro-mechanical switches most often relied upon in the past. Constructed of rigid, durable ABS polymer ultrasonically welded.
PAGE 13
ST-2005 SERIES SUB. PUMP — FLOAT SWITCH (PIGGY-BACK) Float Switch Single or dual control float switches can be used for the unattended operation of the submersible pump. When using the piggyback power configuration (plug), the ST-2005 series pumps DO NOT require the use of a control box. In this configuration (piggyback), the SW-1 (single float switch) or SW-2 (dual float switch) are required. Figure 6 is an example of a single float switch application. Mounting The Float Switch 1.
PAGE 14
ST-2005 SERIES SUB. PUMP — FLOAT SWITCH (CONTROL BOX) Control Box (CB3) For special remote pumping applications of the submersible pump, a control box (Model CB3) may be required. This water resistant control box provides watertight housing and glands to prevent water from leaking into the box, and a float switch interface. When using the CB3 control box, only the SW-1WOP float switch (2) can be used (no plug, bare wires). Shown below (Figure 7) is a wiring layout of the CB3 control box.
PAGE 15
ST-2005 SERIES SUB. PUMP — OPERATION Hose Connections 1. Connect a 2-inch hose to the discharge port on the pump as shown in Figure 8. Make sure that the hose is attached correctly to the discharge port. Pump Power Connections (Piggy-Back Cord Only) 1. Make sure the circuit breaker supplying power to the pump is in the OFF position. 2. Connect the float switch or switches to the AC power receptacle as shown in Figure 6. Attaching Lifting Rope 1.
PAGE 16
ST-2005 SERIES SUB. PUMP— CONTROL BOX INSTALLATION DANGER The ST-2005 series submersible pumps are also designed to work with a control box (Model CB3). This control box contains the necessary electronics (electronic overload module, float switch connections) to operate the pump. Remember this control box contains hazardous voltages. Disconnect all sources of power before installing or servicing.
PAGE 17
ST-2005 SERIES SUB. PUMP— CONTROL BOX INSTALLATION Connecting AC Power to the Control Box 1. 2. 3. The AC power cord (input) should have three wires. Each wire is color coded. The colors are WHITE, BLACK and GREEN. Remove the AC input connector housing from the control box, then route the power cord through the cable gland on the control box. Connect the AC power cord to the contactor as shown in Figure 7 and Table 6. 2.
PAGE 18
ST-2005 SERIES SUB. PUMP — CLEAN-UP Pump Shut-Down/Clean-up 1. Remove the power from the pump by turning off the circuit breaker or switch that provides power to the pump. Remember to make sure that hands are dry (not wet), and feet are not standing in water when removing disconnecting power from the pump. 2. Using the lifting rope, lift the pump up from its current position. Remove the discharge hose from the discharge port on the pump. 3. Remove all power cables and float switches from the control box.
PAGE 19
ST-2005 SERIES SUB. PUMP — MAINTENANCE LUBRICATION To check the oil level of the mechanical seal perform the following: 1. Lay the pump (Figure 11) on its side with the oil plug facing upwards. 2. Remove oil fill plug. 3. Visually inspect oil plug hole to verify that oil cavity is full enough to cover seal spring. Check every 300 hours, change hydraulic oil every 6 months (1,000 hours) or as needed. 5. If oil level is low fill with SAE 10 weight non-detergent hydraulic oil (i.e.
PAGE 20
ST-2005 SERIES SUB. PUMP — TROUBLESHOOTING Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, use Table 8 (Pump Troubleshooting) as a basic guideline for troubleshooting the pump. If the problem cannot be remedied, contact Multiquip's service department. TABLE 8. PUMP TROUBLESHOOTING SYMPTOM POSSIBLE PROBLEM SOLUTION Incorrect voltage/amps? Check that proper voltage (115 VAC, 60 Hz, single-phase ) is being supplied to the pump.
PAGE 21
ST-2005 SERIES SUB. PUMP — PERFORMANCE CURVES 60 ST-2005CUL Performance Curve 60 TOTAL HEAD TOTAL HEAD Max 34 FT Max 42 FT CAPACITY 40 CAPACITY Max 72 G.P.M 20 Max 85 G.P.M 40 20 0 30 60 90 Capacity(US.G.P.M) 0 30 60 90 Capacity(US.G.P.M) 0 ST-2005S Performance Curve 60 ST-2005C Performance Curve TOTAL HEAD Max 36 FT CAPACITY Max 70 G.P.
PAGE 22
ST-2005 SERIES SUB. PUMP — WIRING DIAGRAMS PAGE 22 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 23
NOTE PAGE ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 24
ST-2005 SERIES SUB. PUMP — EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. NOTE Items Found In the “Remarks” Column T he contents of this parts catalog are subject to change without notice. Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
PAGE 25
ST-2005 SERIES SUB. PUMP — SUGGESTED SPARE PARTS ST-2005T/TCUL SUBMERSIBLE PUMP 1 TO 3 UNITS Qty. P/N Description 1 ............ 0202005T120 ................. AC CORD W/ GLAND 1 ............ 0202005T081 ................. OIL SEAL 1 ............ 0202005T112 ................. OIL SEAL 1 ............ 0202005T008 ................. PACKING, CASING 1 ............ 0202005T060 ................. MECHANICAL SEAL 1 ............ 0202005T074 ................. PACKING 1 ............ 0202005TCUL157 ......... PACKING 1 ...
PAGE 26
ST-2005T/TCUL — ELECTRIC SUBMERSIBLE PUMP ASSY. ST-2005T - ST-2005TCUL - ELECTRIC SUBMERSIBLE PUMP ASSY. 128 127 128 125 120 158 121 224 125 156 157 445 34 446 42 23 7 119 76 81 447 160 65 3 24 4 8 16 6 74 112 5 60 1 530 531 PAGE 26 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 27
ST-2005T/TCUL — ELECTRIC SUBMERSIBLE PUMP ASSY. ST-2005T - ST-2005TCUL - ELECTRIC SUBMERSIBLE PUMP ASSY.
PAGE 28
ST-2005/A/CUL — ELECTRIC SUBMERSIBLE PUMP ASSY. ST-2005 - ST-2005A - ST-2005CUL SUBMERSIBLE PUMP ASSY. 102 265 641 125 120 236 104 263 266 121 563 103 127 123 122 174 60 65 131 214-1 1 224 132 474 299 129 179 445 119 446 81 130 447 160 47 3 6 5 214-2 4 8 176 177 112 146 147 PAGE 28 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 29
ST-2005/A/CUL — ELECTRIC SUBMERSIBLE PUMP ASSY. ST-2005 - ST-2005A - ST-2005CUL SUBMERSIBLE PUMP ASSY.
PAGE 30
ST-2005/A/CUL — ELECTRIC SUBMERSIBLE PUMP ASSY. ST-2005 - ST-2005A - ST2005CUL SUBMERSIBLE PUMP ASSY. 102 265 641 125 120 236 104 263 266 121 563 103 127 123 122 174 60 65 131 214-1 1 224 132 474 299 129 179 445 119 446 81 130 447 160 47 3 6 5 214-2 4 8 176 177 112 146 147 PAGE 30 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 31
ST-2005/A/CUL — ELECTRIC SUBMERSIBLE PUMP ASSY. ST-2005 - ST-2005A - ST-2005CUL SUBMERSIBLE PUMP ASSY. NO 176 177 179 214-1 214-2 224 236 263 265 266 299 299 445 446 446 447 447 474 563 641 PART NO 0202005A176 0201503A177 0202005A179 0201503UL214A 0201503A214B 0201503A224 0202005S236 0401450080 011206020 952404470 0202005299 0202005A299 0202005A445 0202005UL446 0202005A446 0202005A447 0201503A447 0201503A474 0201503A563 030208200 PART NAME QTY.
PAGE 32
ST-2005SB — ELECTRIC SUBMERSIBLE PUMP ASSY. ST-2005SB SUBMERSIBLE PUMP ASSY. PAGE 32 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 33
ST-2005SB — ELECTRIC SUBMERSIBLE PUMP ASSY. ST-2005SB SUBMERSIBLE PUMP ASSY.
PAGE 34
ST-2005T — ELECTRIC MOTOR ASSY. ST-2005T ELECTRIC MOTOR ASSY. PAGE 34 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 35
ST-2005T — ELECTRIC MOTOR ASSY. ST-2005T ELECTRIC MOTOR ASSY. NO 112 * 269 * 270 * 273 * 445 * 446 * 447-1 * 447-2 * 539 * 606 * 607 * 608 * A PART NO 0202005T112 0202005T269 0202005T270 0202005T273 0202005T445 0202005T446 0202005T4471 0202005T4472 0202005T539 0202005T606 0202005S607 0202005T608 0202005T119 PART NAME QTY.
PAGE 36
ST-2005TCUL — ELECTRIC MOTOR ASSY. ST-2005TCUL ELECTRIC MOTOR ASSY. PAGE 36 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 37
ST-2005TCUL — ELECTRIC MOTOR ASSY. ST-2005TCUL ELECTRIC MOTOR ASSY. NO 112 * 269 * 270 * 273 * 445 * 446 * 447-1 * 447-2 * 539 * 606 * 607 * 608 * A PART NO 0202005T112 0202005T269CUL 0202005T270 0202005T273 0202005T445 0202005T446 0202005T4471 0202005T4472 0202005T539 0202005T606 0202005S607 0202005T608 0202005TCUL119 PART NAME QTY.
PAGE 38
ST-2005CUL — ELECTRIC MOTOR ASSY. ST-2005CUL ELECTRIC MOTOR ASSY. PAGE 38 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 39
ST-2005CUL — ELECTRIC MOTOR ASSY. ST-2005CUL ELECTRIC MOTOR ASSY. NO 112 * 129* 130* 131* 132* 268* 269 * 270 * 273 * 445 * 446 * 447-1 * 447-2 * 539 * 540* 541* 606 * 607 * 608 * A PART NO 0201503A112 0202005A129 0202005UL130 0202005A131 0201503A132 0201503A268 0202005A269 0202005UL270 0202005UL273 0202005A445 0202005UL446 0202005T4471 0201503A4472 0202005T539 0201503UL540 0201503UL541 0202005T606 0202005S607 0202005T608 0202005UL119 PART NAME QTY.
PAGE 40
ST-2005SB — ELECTRIC MOTOR ASSY. ST-2005SB ELECTRIC MOTOR ASSY. PAGE 40 — ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 41
ST-2005SB — ELECTRIC MOTOR ASSY. ST-2005SB ELECTRIC MOTOR ASSY. NO 112 * 129* 130* 131* 132* 268* 269 * 270 * 273 * 445 * 446 * 447-1 * 447-2 * 539 * 540* 541* 606 * 607 * 608 * A PART NO 0201503A112 0202005A129 0202005A130 0202005A131 0201503A132 0201503A268 0202005A269 0202005A270 0202005A273 0202005A445 0202005A446 0201503A4471 0201503A4472 0202005T539 0201503A540 0201503A541 0202005T606 0202005S607 0202005T608 0202005SB119 PART NAME QTY.
PAGE 42
Effective: October 1, 2002 PAYMENT TERMS TERMS AND CONDITIONS OF SALE — PARTS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin.
PAGE 43
NOTE PAGE ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV.
PAGE 44
OPERATION AND PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING MULTIQUIP CORPORATE OFFICE 18910 Wilmington Ave. Carson, CA 90746 Email: mq@multiquip.com Internet: www.multiquip.com PARTS DEPARTMENT 800-427-1244 310-537-3700 MAYCO PARTS 800-306-2926 310-537-3700 SERVICE DEPARTMENT 800-421-1244 310-537-3700 TECHNICAL ASSISTANCE 800-478-1244 WARRANTY DEPARTMENT 800-421-1244, EXT. 279 310-537-3700, EXT.