PARTS AND OPERATION MANUAL OPERATION AND PARTS MANUAL ULTRA-SILENTTM SERIES MODEL DCA-70SSIU 60 Hz GENERATOR PARTS LIST NO. M2870300504 Revision #1 (01/06/09) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PAGE 2 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING MQ POWER CORPORATE OFFICE 18910 Wilmington Ave. 800-421-1244 Carson, CA 90746 FAX: 310-632-2656 Email: mqpower@multiquip.com Internet: www.mqpower.com PARTS DEPARTMENT 800-427-1244 FAX: 800-672-7877 310-537-3700 FAX: 310-637-3284 SERVICE DEPARTMENT 800-835-2551 FAX: 310-638-8046 310-537-3700 TECHNICAL ASSISTANCE 800-835-2551 FAX: 310-638-8046 WARRANTY DEPARTMENT 800-835-2551, EXT. 279 FAX: 310-638-8046 310-537-3700, EXT.
TABLE OF CONTENTS MQ POWER DCA-70SSIU (60HZ) SUPER-SILENT GENERA TOR GENERATOR California Proposition 65 Warning ..................................... 2 Here's How To Get Help .................................................... 3 Table Of Contents ............................................................. 4 Parts Ordering Procedures ............................................... 5 Specifications ................................................................... 6 Dimensions (Top, Side, Front) ........
PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ ❒ ❒ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: ✓ FedEx or UPS Ground Note: Unless otherwise indicated by customer, all ✓ FedEx or UPS Second Day or Third Day orders are treated as “Standard Orders”, and will ✓ FedEx or UPS Nex
DCA-70SSIU (60 Hz) — SPECIFICATIONS Table 1. Generator Specifications Model DCA-70SSIU Type Revolving field, self ventilated, open protected type synchronous generator Armature Connection Star with Neutral Zig Zag Phase 3 Single Standby Output 73.5 KVA (58.8 KW) 42 KW Prime Output 70 KVA (56 KW) 40 Kw Voltage 240V or 480V 240/120 Frequency 60 Hz S pe e d 1800 r pm Power Factor 0.8 1 Aux. AC Power Single Phase, 60 Hz Voltage 120 V Output 4.8 KW (2.4 KW x 2) Table 2.
DCA-70SSIU (60 Hz) — DIMENSIONS (TOP, SIDE AND FRONT) B C D E A TOP VIEW 70 SIDE VIEW F FRONT VIEW G Denyo TABLE 3. DIMENSIONS Reference Letter Dimension in. (mm.) Reference Letter Dimension in. (mm.) A 31.10 in. (790 mm.) F 105.11 in. (2,670 mm.) B 30.15 in. (766 mm.) G 68.30 in. (1,735 mm.) C 30.15 in. (766 mm.) H 37.40 in. (950 mm.) D 30.15 in. (766 mm.) E 30.15 in. (766 mm.) H Figure 1. Dimensions 1 DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. NOTE This Operation and Parts Manual has been developed to provide complete instructions for the safe and efficient operation of the MQ Power Model DCA-70SSIU (60Hz) SuperSilent™ Generator.
DCA-70SSIU (60 Hz) — SAFETY MESSAGE ALERT SYMBOLS WARNING - ROTATING PARTS NEVER operate equipment with covers, or guards removed. Keep fingers, hands, hair and clothing away from all moving parts to prevent injury. CAUTION - ACCIDENTAL STARTING ALWAYS place the Engine ON/OFF switch in the OFF position and remove the ignition key when the pump is not in use. CAUTION - OVER-SPEED CONDITIONS NEVER tamper with the factory settings of the engine governor or settings.
DCA-70SSIU (60 Hz) — RULES FOR SAFE OPERATION DANGER - READ THIS MANUAL! Failure to follow instructions in this manual may lead to serious injury or even DEATH! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the DCA-70SSIU (60 Hz) Ultra Silent™ Generator. General Safety: ■ DO NOT operate or service this equipment before reading this entire manual.
DCA-70SSIU (60 Hz) — RULES FOR SAFE OPERATION Generator Grounding To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground. Article 250 (Grounding) of the National Electrical Code (NEC) provides guide lines for proper grounding and specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
DCA-70SSIU (60 Hz) — RULES FOR SAFE OPERATION Maintenance Safety Battery Safety ■ The electrical voltage required to operate the generator can cause severe injury or even death through physical contact with live circuits. Turn all circuit breakers OFF before performing maintenance on the generator. Use the following guidelines when handling the battery: ■ NEVER lubricate components or attempt service on a running machine.
DCA-70SSIU (60 Hz) — RULES FOR SAFE OPERATION ■ The maximum speed for highway towing is 55 MPH unless posted otherwise. Recommended off-road towing To reduce the possibility of an accident while transporting is not to exceed 15 MPH or less depending on type of the generator on public roads, always make sure the trailer terrain. that supports the generator and the towing vehicle are in good operating condition and both units are mechanically ■ Place chock blocks underneath wheel to prevent rolling, sound.
DCA-70SSIU (60 Hz) — GENERATOR DECALS The DCA-70SSIU (60 Hz) SuperSilent™ Generator is equipped with a number of safety decals (Figures 2 & 3). These decals are provided for operator safety and maintenance information. The illustration below and on the preceding page show the decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer. Figure 2. Generator Decals PAGE 14 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — GENERATOR DECALS Figure 3. Generator Decals (Cont inued) 1 DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — INSTALLATION Figure 4. Typical Generator Grounding Application PAGE 16 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — INSTALLATION Outdoor Installation Generator Grounding Install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift around. Also install the generator in a manner so that the exhaust will not be discharged in the direction of nearby homes. To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground.
DCA-70SSIU (60 Hz) — GENERAL INFORMATION DCA-70SSIU Ultra Silent™ (60 Hz) Series Familiarization Generator The MQ Power Model DCA-70SSIU (60 Hz) is a 56 kW generator (Figure 5) that is designed as a high quality portable (requires a trailer for transport) power source for telecom sites, lighting facilities, power tools, submersible pumps and other industrial and construction machinery.
DCA-70SSIU (60 Hz) — MAJOR COMPONENTS 1 2 3 70 WHISPERWATT 4 7 5 6 Table 4. Generator Major Components ITEM NO.
NOTE PAGE PAGE 20 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — GENERATOR CONTROL PANEL Figure 6. Generator Control Panel The definitions below describe the controls and functions of the Located behind the generator control panel is the Generator Control Box. This box contains some of the necessary DCA-70SSIU (60 Hz) Generator Control Panel (Figure 6). 1. Main Circuit Breaker – This three-pole, 175A main electronic components required to make the generator breaker is provided to protect the the U,V, and W Output function. 2. 3. 4. 5. 6. 7.
DCA-70SSIU (60 Hz) — ENGINE OPERATING PANEL Figure 7. Engine Operating Panel PAGE 22 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — ENGINE OPERATING PANEL The definitions below describe the controls and functions of During cranking cycle , The MPEC will attempt to crank the the DCA-70SSIU (60 Hz) Engine Operating Panel (Figure 7). engine for 10 seconds before disengaging. If the engine does not engage (start) by the third attempt, the engine will be 1. Panel Light – Normally used in dark areas or at night shutdown by the engine controller’s Over Crank Protection time. When activated, panel lights will illuminate.
DCA-70SSIU (60 Hz) — OUTPUT TERMINAL PANEL FAMILIARIZATION Output Terminal Panel Output Terminal Familiarization The Output Terminal Panel (Figure 8) shown below is located The “Output Terminal Panel ” (Figure 8) is provided with the on the right-hand side (left from control panel) of the generator. following: Lift up on the cover to gain access to receptacles and terminal ■ Three (3) 120/240V output receptacles @ 50 amp lugs.
DCA-70SSIU (60 Hz) — OUTPUT TERMINAL PANEL FAMILIARIZATION 120 VAC GFCI Receptacles There are two 120 VAC, 20 amp GFCI (Duplex Nema 5-20R) recepacles provided on the output terminal panel. These receptacles can be accessed in any voltage selector switch position. Each receptacle is protected by a 20 amp circuit breaker. These breakers are located directly above the GFCI receptacles.
DCA-70SSIU (60 Hz) — OUTPUT TERMINAL PANEL FAMILIARIZATION Connecting Loads Blower Fan Loads can be connected to the generator by the Ouput Terminal Lugs or the convienience receptacles (Figure 13). Make sure to read the operation manual before attempting to connect a load to the generator. This unit has an intake fan located at the rear of the machine to draw outside air into the cabinet to cool the engine. The fan has a 10 amp AC fuse located beneath the Voltage Selector Switch (Figure 15).
DCA-70SSIU (60 Hz) — LOAD APPLICATION Single Phase Load Three Phase Load Always be sure to check the nameplate on the generator and equipment to insure the wattage, amperage, frequency, and voltage requirements are satisfactorily supplied by the generator for operating the equipment. When calculating the power requirements for 3-phase power use the following equation: Generally, the wattage listed on the nameplate of the equipment is its rated output.
DCA-70SSIU (60 Hz) — GENERATOR OUTPUTS Voltage Selector Switch Generator Amperage The voltage selector switch (Figure 16) is located above Table 8 describes the generator’s current output capability the output terminal panel’s Hard Wire Hook-up Panel. It for both 1Ø-phase and 3Ø phase applications. has been provided for ease of voltage selection. Table 8.
DCA-70SSIU (60 Hz) — GAUGE READING How to Read the Output Terminal Gauges. The gauges and selector switches on the control panel DO NOT effect the generator output. They are provided to help observe how much power is being supplied at the Output terminals lugs. Before taking a reading from either gauge, set the Voltage Selector Switch (Figure 17) to the position which produces the required voltage (For example, for 3Ø 240V, choose the center 3Ø 240/ 139V position on the voltage selector switch.
DCA-70SSIU (60 Hz) — OUTPUT TERMINAL PANEL CONNECTIONS UVWO Terminal Output Voltages Various output voltages can be obtained using the Output Terminal Lugs. The voltages at the terminals are dependent on the position of the Voltage Selector Switch and the adjustment of the Voltage Regulator Control Knob. Remember the voltage selector switch determines the range of the output voltage. The voltage regulator (VR) allows the user to increase or decrease the selected voltage.
DCA-70SSIU (60 Hz) — OUTPUT TERMINAL PANEL CONNECTIONS 3Ø 480/277 Output Terminal Lug Voltages 1Ø 240V/120V Output Terminal Lug Voltages 1. Place the voltage selector switch in the 3Ø 480/277 1. Place the voltage selector switch in the 1Ø 240/120 position as shown in Figure 27. position as shown in Figure 29. Figure 27. Voltage Selector Switch 480/277V Three-Phase Position Figure 29. Voltage Selector Switch 240/120V Single-Phase Position 2. Connect the load wires to the Output Terminal Lugs as 2.
DCA-70SSIU (60 Hz) — PRE-SETUP Circuit Breakers To protect the generator from an overload, a 3-pole, 175 amp, main circuit breaker is provided to protect the U,V, and W Output Terminals from overload. In addition two single-pole, 20 amp GFCI circuit breakers are provided to protect the GFCI receptacles from overload. Three 50 amp load circuit breakers have also been provided to protect the auxiliary receptacles from overload.
DCA-70SSIU (60 Hz) — PRE-SETUP Refueling Procedure: 3. WARNING - RESPIRATORY HAZARDS Open cabinet doors on the “right side” of the generator (from generator control panel position). Remove fuel cap and fill tank (Figure 34). Diesel fuel and its vapors are dangerous to your health and the surrounding environment. Avoid skin contact and/or inhaling fumes. 1. Level Tanks – Make sure fuel cells are level with the ground.
DCA-70SSIU (60 Hz) — PRE-SETUP Coolant (ISUZU Antifreeze/Summer Coolant/Water) ISUZU recommends ISUZU Antifreeze/Summer Coolant for use in thier engines, which can be purchased in concentrate (and mixed with 50% demineralized water) or pre-diluted. See the ISUZU Engine Owner's Manual for further details. Cleaning the Radiator The engine may overheat if the radiator fins become overloaded with dust or debris. Periodically clean the radiator fins with compressed air.
DCA-70SSIU (60 Hz) — PRE-SETUP When connecting battery do the following: Battery This unit is of negative ground DO NOT connect in reverse. 1. NEVER connect the battery cables to the battery terminals when the MPEC Control Switch is in either Always maintain battery fluid level between the specified the MANUAL position. ALWAYS make sure that the MPEC marks. Battery life will be shortened, if the fluid level are not Control Switch is in the OFF/RESET position when properly maintained.
DCA-70SSIU (60 Hz) — GENERATOR START-UP PROCEDURE (MANUAL) Before Starting CAUTION - LETHAL EXHAUST HAZARD The engine's exhaust contains harmful emissions. ALWAYS have adequate ventilation when operating. Direct exhaust away from nearby personnel. 5. Place the voltage selector switch in the desired voltage position (Figure 41). Figure 41. Voltage Selector Switch WARNING - STARTING THE GENERATOR NEVER! manually start the engine with the main, GFCI or auxiliary circuit breakers in the ON (closed) position.
DCA-70SSIU (60 Hz) — GENERATOR START-UP PROCEDURE (MANUAL) 10.Verify that the Engine Running status LED on the MPEC unit (Figure 45) is ON (lit) after the engine has been started. Figure 45. Engine Running LED (ON) 11. The generator's frequency meter (Figure 46) should be displaying the 60 cycle output frequency in HERTZ. 14. The engine oil pressure gauge (Figure 50) will indicate the oil pressure (kg/ cm2) of the engine. Under normal operating conditions the oil pressure is approximately 35~65 PSI.
DCA-70SSIU (60 Hz) — GENERATOR START-UP PROCEDURE (AUTO MODE) 19. The generator will run until manually stopped or an abnormal condition occurs. NOTE Starting (Auto Mode) DANGER - ELECTRICAL SYSTEM HAZARDS Before connecting this generator to any building’s electrical system, a licensed electrician must install an isolation (transfer) switch. Serious damage to the building’s electrical system may occur without this transfer switch.
DCA-70SSIU (60 Hz) — MAINTENANCE 10 Hrs DAILY TABLE 14.
DCA-70SSIU (60 Hz) — MAINTENANCE Flushing Out Radiator and Replacing Coolant Air Removal If air enters the fuel injection system of a diesel engine, Open both cocks located at the crankcase side and at the lower part of the radiator and drain coolant. Open the starting becomes impossible. After running out of fuel, or radiator cap while draining. Remove the overflow tank after disassembling the fuel system, bleed the system and drain. according to the following procedure.
DCA-70SSIU (60 Hz) — MAINTENANCE If the generator will be used daily, the battery should normally not require charging. If the generator will be idle (not used) This generator can be optionally equipped with two 120 VAC, for long periods of time, apply power to the battery charger 20 amp input receptacles located on the output terminal receptacle via commercial power using an power cord of adequate size. panel.
DCA-70SSIU (60 Hz) — TRAILER MAINTENANCE Trailer Maintenance 7. Coupler - Type of hitch used on the trailer for towing. This section is intended to provide the user with generic 8. Tire Size - Indicates the diameter of the tire in inches trailer service and maintenance information. The service and (10,12,14, etc.), and the width in millimeters maintenance guidelines referenced in this section refer to a (175,185,205, etc.). The tire diameter must match the wide range of trailers. diameter of the tire rim.
DCA-70SSIU (60 Hz) — TRAILER MAINTENANCE Brakes Trailer brakes should be inspected the first 200 miles of operation. This will allow the brake shoes and drums to seat properly. After the first 200 mile interval, inspect the brakes every 3,000 miles. If driving over rough terrain, inspect the brakes more frequently. Figure 58 displays the major hydraulic surge brake components that will require inspection and maintenance.
DCA-70SSIU (60 Hz) — TRAILER MAINTENANCE Tires/Wheels/Lug Nuts Tires and wheels are a very important and critical components of the trailer. When specifying or replacing the trailer wheels it is important the wheels, tires, and axle are properly matched. CAUTION - EYESIGHT HAZARD Suspension The leaf suspension springs and associated components (Figure 59) should be visually inspected every 6,000 miles for signs of excessive wear, elongation of bolt holes, and loosening of fasteners.
DCA-70SSIU (60 Hz) — TRAILER MAINTENANCE Lug Nut Torque Requirements It is extremely important to apply and maintain proper wheel mounting torque on the trailer. Be sure to use only the fasteners matched to the cone angle of the wheel. Proper procedure for attachment of the wheels is as follows: 1. Start all wheel lug nuts by hand. 2. Torque all lug nuts in sequence (see Figure 60). DO NOT torque the wheel lug nuts all the way down. Tighten each lug nut in 3 separate passes as defined by Table 18. 3.
DCA-70SSIU (60 Hz) — TRAILER WIRING DIAGRAM Figure 61. Trailer/Towing Vehicle Wiring Diagram PAGE 46 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
NOTE PAGE 1 DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — GENERATOR WIRING DIAGRAM Figure 62. Generator Wiring Diagram PAGE 48 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — ENGINE WIRING DIAGRAM Figure 63. Engine Wiring Diagram 1 DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — TROUBLESHOOTING (GENERATOR) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, use Table 19 shown below for diagnosis of the Generator. If the problem cannot be remedied, consult our company's business office or service plant. TABLE 19.
DCA-70SSIU (60 Hz) — TROUBLESHOOTING (ENGINE CONTROLLER) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, use Table 20 (Engine Controller Troubleshooting) as a basic guideline for troubleshooting the Microprocessor Engine Controller unit (MPEC). If the problem cannot be remedied, consult our company's business office or service plant. TABLE 20. ENGINE CONTROLLER TROUBLESHOOTING (MPEC) SYMPTOM Low oil pressure light is on.
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
DCA-70SSIU (60 Hz) — SUGGESTED SPARE PARTS DCA-70SSIU (60 Hz) WHISPER WATTGENRATOR W/ISUZU FF4BG1T DIESEL ENGINE 1 TO 3 UNITS Qty. P/N Description 5 ......... 1132402321 ........ FILTER, OIL 5 ......... 1132400791 ........ FILTER, FUEL, PRIMARY 3 ......... 0602046365 ........ ELEMENT, AIR 1 ......... 8972333820 ........ BELT, FAN 1 ......... 0605505070 ........ CAP. FUEL TANK 1 ......... 0602122272 ........ UNIT, OIL PRESSURE 1 ......... 0602123260 ........ UNIT, WATER TEMPERATURE 2 ......... 0601802149 ...
DCA-70SSIU (60 HZ) — GENERATOR ASSY. GENERATOR ASSY. PAGE 54 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — GENERATOR ASSY. GENERATOR ASSY. NO. PART NO.
DCA-70SSIU (60 Hz) — CONTROL BOX ASSY. CONTROL BOX ASSY. PAGE 56 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — CONTROL BOX ASSY. CONTROL BOX ASSY. NO. 1 2-1 2-2 3 3-1 4 5 6 7 8 9 10 11 12 13 13A 14 15 16 16A 16B 17 17-1 17-2 17-3 18 18A 18B 18C 19 20 21 21-1 21-2 21-3 22 23 24 25 26 27 27A 27B 28 29 30 31 32 PART NO.
DCA-70SSIU (60 Hz) — CONTROL BOX ASSY. (CONT.) CONTROL BOX ASSY. PAGE 58 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — CONTROL BOX ASSY. (CONT.) CONTROL BOX ASSY. NO. 33 34 35 35A 36 37 38 39 40 41 42 43 44 45 46 47 47-1 48 49 50 51 52 52A 53 54 55 56 57 58 59 60 61 62 63 64 65 66 66-1 67 68 69 70 71 72 73 73A 74 75 76 77 PART NO.
DCA-70SSIU (60 Hz) — ENGINE AND RADIATOR ASSY. ENGINE AND RADIATOR ASSY. PAGE 60 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — ENGINE AND RADIATOR ASSY. ENGINE AND RADIATOR ASSY. NO. 1 1-1 1-2 2 3 4 5 6 7 8 9 10 11 11-1 11-2 12 13 14 15 16 17 18 19 20 21 22 23 24 25 25A 25-1 26 27 28 29 30 31 32 33 34 35 36 37 38 PART NO.
DCA-70SSIU (60 Hz) — ENGINE AND RADIATOR ASSY. (CONT.) ENGINE AND RADIATOR ASSY. PAGE 62 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — ENGINE AND RADIATOR ASSY. (CONT.) ENGINE AND RADIATOR ASSY. NO. 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 PART NO. 0605511395 0603306395 0602021070 0269200500 M9300000103 M9300100003 0199900400 0199900175 0193601800 0605515106 M2316100304 0016908020 8972333820 0602123260 9827200690 PART NAME QTY. REMARKS VALVE 1 HOSE JOINT 1 CAP 1 DRAIN HOSE 1 RESERVE TANK 1 RESERVE TANK CAP 1 HOSE 1 HOSE 1 HOSE 1 HOSE BAND 3 RESERVE TANK BRACKET 1 HEX HEAD BOLT 2 FAN BELT .........................
DCA-70SSIU (60 Hz) — OUTPUT TERMINAL ASSY. OUTPUT TERMINAL ASSY. ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER WHEN ORDERING ANY PAINTED PANEL TO INDICATE COLOR OF UNIT: 1-ORANGE 2-WHITE 3-SPECTRUM GREY 4-SUNBELT GREEN 5-BLACK 6-CATERPILLAR YELLOW 7-CATO GOLD 8-RED THE SERIAL NUMBER MAY BE REQUIRED. PAGE 64 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — OUTPUT TERMINAL ASSY. OUTPUT TERMINAL ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 13A 13B 14 14A 15 16 17 18 19 20 21 22 22-1 23 24 25 26 26A 27 28 29 30 31 32 33 34 35 PART NO.
DCA-70SSIU (60 Hz) — ACTUATOR ASSY. ACTUATOR ASSY. PAGE 66 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — ACTUATOR ASSY. ACTUATOR ASSY. NO. 1 1-1 2 3 3A 3B 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NO.
DCA-70SSIU (60 Hz) — BATTERY ASSY. BATTERY ASSY. PAGE 68 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — BATTERY ASSY. BATTERY ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. 0602220187 M9310500014 M9103000304 0602220920 0040006000 M2346900004 M2346900104 0017112025 0040512000 0017110020 0040512000 0602220622 PART NAME QTY. REMARKS BATTERY 1 BATTERY SHEET 1 BATTERY BAND 1 BATTERY BOLT SET 2 SPRING WASHER 2 BATTERY CABLE 1 BATTERY CABLE 1 HEX HEAD BOLT 1 TOOTHED WASHER 1 HEX HEAD BOLT 1 TOOTHED WASHER 1 TERMINAL CAP 1 CABLE ................................................................
DCA-70SSIU (60 Hz) — MUFFLER ASSY. MUFFLER ASSY. PAGE 70 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — MUFFLER ASSY. MUFFLER ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 PART NO. B5330100303 0016910025 M2333001203 3943690210 M2333200504 0039308000 0016908040 M2333300204 M2333300304 0016908020 0602326090 PART NAME QTY. REMARKS MUFFLER 1 HEX HEAD BOLT 4 EXHAUST PIPE 1 GASKET ................................................................. 1 .........
DCA-70SSIU (60 Hz) — FUEL TANK ASSY. FUEL TANK ASSY. PAGE 72 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — FUEL TANK ASSY. FUEL TANK ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART NO.
DCA-70SSIU (60 Hz) — ENCLOSURE ASSY. ENCLOSURE ASSY. ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER WHEN ORDERING ANY PAINTED PANEL TO INDICATE COLOR OF UNIT: 1-ORANGE 2-WHITE 3-SPECTRUM GREY 4-SUNBELT GREEN 5-BLACK 6-CATERPILLAR YELLOW 7-CATO GOLD 8-RED THE SERIAL NUMBER MAY BE REQUIRED. PAGE 74 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — ENCLOSURE ASSY. ENCLOSURE ASSY. NO. PART NO.
DCA-70SSIU (60 Hz) — ENCLOSURE ASSY. (CONT.) ENCLOSURE ASSY. ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER WHEN ORDERING ANY PAINTED PANEL TO INDICATE COLOR OF UNIT: 1-ORANGE 2-WHITE 3-SPECTRUM GREY 4-SUNBELT GREEN 5-BLACK 6-CATERPILLAR YELLOW 7-CATO GOLD 8-RED THE SERIAL NUMBER MAY BE REQUIRED. PAGE 76 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — ENCLOSURE ASSY. (CONT.) ENCLOSURE ASSY. NO. PART NO.
DCA-70SSIU (60 Hz) — RUBBER SEALS ASSY. RUBBER SEALS ASSY. PAGE 78 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — RUBBER SEALS ASSY. RUBBER SEALS ASSY. NO. PART NO.
DCA-70SSIU (60 Hz) — NAME PLATE AND DECALS ASSY. NAMEPLATE AND DECALS ASSY. PAGE 80 — DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
DCA-70SSIU (60 Hz) — NAME PLATE AND DECALS ASSY. NAMEPLATE AND DECALS ASSY. NO. PART NO.
Effective: October 1, 2002 PAYMENT TERMS TERMS AND CONDITIONS OF SALE — PARTS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin.
NOTE PAGE 1 DCA-70SSIU (60 Hz) — OPERATION AND PARTS MANUAL — REV.
PARTS AND OPERATION MANUAL OPERATION AND PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING MQ POWER CORPORATE OFFICE 18910 Wilmington Ave. 800-421-1244 FAX: 310-632-2656 Carson, CA 90746 Email: mqpower@multiquip.com Internet: www.mqpower.
