PARTS AND OPERATION MANUAL PARTS AND OPERATION MANUAL © COPYRIGHT 2001, MULTIQUIP INC. MQ POWER DCA-60SSAI TM WHISPERWATT GENERATOR (Standard) PARTS LIST NO. 7451201B FINAL COPY MULTIQUIP INC. PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT: 310-537-3700 800-421-1244 800-835-2551 FAX: 310-537-3927 FAX: 310-638-8046 E-mail:mq@multiquip.com • www:multiquip.
PAGE 2 — DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01)
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PAR TS DEP AR TMENT ARTS DEPAR ARTMENT 800/427-1244 or 310/537-3700 FAX: 800/672-7877 or 310/637-3284 VICE DEP AR TMENT SER ARTMENT SERVICE DEPAR 800/835-2551 or 310/537-3700 FAX: 310/638-8046 WARRANTY DEP AR TMENT DEPAR ARTMENT 800/835-2551 or 310/537-3700 FAX: 310/638-8046 MAIN 800/421-1244 or 310/537-3700 FAX: 310/537-3927 DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01) — PAGE 3
TABLE OF CONTENTS Here's How To Get Help ........................................... 3 Table Of Contents .................................................... 4 Parts Ordering Procedures ...................................... 5 Rules for Safe Operation ......................................... 6-9 Towing and Transportation ....................................... 10 Trailer Safety Guidelines .......................................... 11-17 Trailer Wiring Diagram ..............................................
PARTS ORDERING PROCEDURES ■ ■ ■ ■ ■ ■ ■ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • • • • UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* • • Airborne Express* Truck or parcel post *Normally shipped the same day the order
RULES FOR SAFE OPERATION CAUTION: Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. ■ NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to cool before servicing engine or generator.
RULES FOR SAFE OPERATION CAUTION: CAUTION: DO NOT touch or open any of the below mentioned components while the generator is running. Always allow sufficient time for the engine and generator to cool before performing maintenance. ■ NEVER touch output terminals during operation. This is extremely dangerous. Always stop the machine when contact with the output terminals is required. CAUTION: ■ Backfeed to a utility system can cause electrocution and.or property damage.
RULES FOR SAFE OPERATION ■ NEVER Run engine without air filter. Severe engine damage may occur. Battery CAUTION: Never over fill the battery with water above the upper limit. The battery contains acids that can cause injury to the eyes and skin. To avoid eye irritation, always wear safety glasses. Use well insulated gloves when picking up the battery. Use the following guidelines when handling the battery: ■ Always service air cleaner frequently to prevent carburetor malfunction.
RULES FOR SAFE OPERATION Transporting ■ Always shutdown engine before transporting. ■ Tighten fuel tank cap securely. ■ Drain fuel when transporting generator over long distances or bad roads. ■ Always tie-down the generator during transportation by securing the generator. ■ If generator is mounted on a trailer, make sure trailer complies with all local and state safety transportation laws. See page 10 for basic towing procedures.
DCA-60SSAI — TOWING RULES FOR SAFE OPERATION Towing Safety Precautions CAUTION : Check with your county or state safety towing regulations department before towing your generator. To reduce the possibility of an accident while transporting the generator on public roads, always make sure the trailer (Figure 1) that supports the generator and the towing vehicle are in good operating condition and both units are mechanically sound.
DCA-60SSAI — TRAILER-SAFETY GUIDELINES CAUTION: ALWAYS make sure the trailer is in good operating condition. Check the tires for proper inflation and wear. Also check the wheel lug nuts for proper tightness. Explanation of Chart: This section is to provide the user with trailer service and maintenance information. The service and maintenance guidelines referenced in this section apply a wide range of trailers.
DCA-60SSAI —TRAILER-SPECIFICATIONS Table 1. Specifications MODEL APPLICATION FU E L C E LL BRAKE SYSTEM GVWR FRAME LENGTH FRAME WIDTH JACK STAND TRLR-10W SDW225, SGW250,TLW300 NO NO 1900LB S 96" 50" 800LB . FULL TILT WHEEL TRLR-10 DCA10, TLG12, DCA-15 NO NO 1900LB S 96" 50" 800LB . FULL TILT WHEEL TRLR-10XF DCA10, TLG-12, DCA15, TLW-300 52 GAL NO 1900LB S 96" 50" 800LB . FULL TILT WHEEL TRLR-225W WELDERS, D A 7000S S NO NO 2200LB S 85" 42" 800LB .
DCA-60SSAI —TRAILER-SPECIFICATIONS Table 1. Specifications (Con't) MODEL COUPLER TIRES WHEELS AXLE HUBS SUSPENSION ELECTRICAL TRLR-10W 2" B A LL C LA S S 2 ADJUSTABLE 175-13C 13"X4.50" 2200# 2X 2 5 LUG 3 LE A F 4 WIRE LOOM W/ 4 POLE FLAT TRLR-10 2" B A LL C LA S S 2 ADJUSTABLE 175-13C 13"X4.5" 2200#2X 2 5 LUG 3 LE A F 4 POLE FLAT TRLR-10XF 2" B A LL C LA S S 2 ADJUSTABLE 175-13C 13"X4.
DCA-60SSAI —TRAILER SAFETY GUIDELINES Brakes If your trailer has a braking system, the brakes should be inspected the first 200 miles of operation. This will allow the brake shoes and drums to seat properly. After the first 200 mile interval, inspect the brakes every 3,000 miles. If driving over rough terrain, inspect the brakes more frequently. Electric Brakes Electrically actuated brakes (Figure 2) are similar to hydraulic brakes.
DCA-60SSAI — TRAILER SAFETY GUIDELINES Figure 2. Electrical Brake Components Hydraulic/Air/Surge Brakes Hydraulic brakes (Figure 3) should not require any special attention with the exception of routine maintenance such as shoe and lining replacement. These brakes can be adjusted in the same manner as electric brakes. Brake lines should be periodically checked for cracks, kinks, or blockage.
DCA-60SSAI — TRAILER SAFETY GUIDELINES Tires/Wheels/Lug Nuts Tires and wheels are a very important and critical components of the trailer. When specifying or replacing the trailer wheels it is important the wheels, tires, and axle are properly matched. CAUTION: DO NOT attempt to repair or modify a wheel. DO NOT install in inner tube to correct a leak through the rim.
DCA-60SSAI —TRAILER SAFETY GUIDELINES Table 3. Suspension Torque Requirements Item Torque (Ft.-Lbs.) 3/8" U-BOLT MIN-30 MAX-35 7/16" U-BOLT MIN-45 MAX-60 1/2" U-BOLT MIN-45 MAX-60 SHACKLE BOLT SNUG FIT ONLY. PARTS MUST ROTATE FREELY. SPRING EYE BOLT LOCKING NUTS OR COTTER PINS ARE PROVIDED TO RETAIN NUT-BOLT ASSEMBLY. MIN-30 MAX-50 SHOULDER TYPE SHACKLE BOLT Lug Nut Torque Requirements It is extremely important to apply and maintain proper wheel mounting torque on the trailer.
DCA-60SSAI —TRAILER-WIRING DIAGRAM NOTE: LIGHTS ARE ORIENTED FROM THE DRIVER’S SEAT PAGE 18 — DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01)
DCA-60SSAI —TRAILER-BRAKE TROUBLESHOOTING Table 5. Electric Brake Troubleshooting Symptom Possible Cause Solution No Brakes or Intermittent Brakes Any open circuits or broken wires? Find and correct. Any shor t circuits? Find and correct. Faulty controller? Test and correct. Any loose connections? Find and repair. Ground wire secure? Find and secure. Grease or oil on magnets or linings? Clean or replace. Connections corroded? Clean and correct cause of corrosion.
DCA-60SSAI —TRAILER-BRAKE TROUBLESHOOTING Table 6. Hydraulic Brake Troubleshooting Symptom Possible Cause Solution No Brakes Brake line broken or kinked? Repair or replace. Weak Brakes or Brakes Pull to One Side Brake lining glazed? Reburnish or replace. Trailer overloaded? Correct weight. Brake drums scored or grooved? Machine or replace. Tire pressure correct? Inflate all tires equally. Tires unmatched on the same axle? Match tires.
DCA-60SSAI — GENERATOR DECALS The DCA -100SSJU generator is wquipped with a number of safety decals. These decals are provided for operator safety and maintenance information. The illustration below and on the preceding pages show the decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
DCA-60SSAI — GENERATOR DECALS PAGE 22 — DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01)
DCA-60SSAI — SPECIFICATIONS Table 7. Specifications Generator Specifications Model DCA-60SSI2 Type Revolving field, self ventilated, open protected type synchronous generator Armature Connection Star with Neutral Zig Zag Phase 3 Single Standby Output 72 KVA (57.6 KW) 41.5KW Prime Output 60 KVA (48 KW) 34.6KW Voltage 240V or 480V 240/120V Frequency 60 Hz Speed 1800 rpm Power Factor 0.8 1 Aux. AC Power Single Phase, 60 Hz Voltage 120 V Output 4.8 KW (2.
DCA-60SSAI — GENERAL INFORMATION DCA-60SSAI FAMILIARIZATION Open Delta Excitation System Generator The DCA-60SSAI generator is equipped with the state of ator the art "Open-Delta" excitation system. The open delta The MQ Power Model DCA-60SSAI is a 48 kW gener generator that is designed as a high quality portable (requires a trailer system consist of an electrically independent winding wound for transport) power source for telecom sites, lighting among stationary windings of the AC output section.
DCA-60SSAI — MAJOR COMPONENTS Figure 6.
DCA-60SSAI — DIMENSIONS (TOP, SIDE AND FRONT) Figure 7.
NOTE PAGE DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01) — PAGE 27
DCA-60SSAI — CONTROL PANEL Figure 8.
DCA-60SSAI — CONTROL PANEL The definitions below describe the controls and functions of the DCA-60SSAI " Control Panel " (Figure 8). 1. Frequency Meter – Indicates the output frequency in hertz (Hz). Normally 60 Hz ±1 Hz . 2. AC Ammeter – Indicates the amount of current the load is drawing from the generator. 3. ACVoltmeter – Indicates the single phase output voltage present at the UNV terminals. 4. Pilot Lamp - This lamp indicates the load is not properly set.
DCA-60SSAI — ENGINE OPERATING PANEL Figure 9.
DCA-60SSAI — ENGINE OPERATING PANEL The definitions below describe the controls and functions of the DCA-60SSAI " Engine Operating Panel " (Figure 9). 1. Oil Pressure Gauge – Normal operation should be about 25 psi. When starting the generator the oil pressure may read a bit higher, but after the engine warms up the oil pressure should return to normal. 2. Panel light - Normally used in dark places or at night. When activated, panel will luminate.
DCA-60SSAI — OUTPUT TERMINAL PANEL Output Terminal Panel The output control panel is located on the rear (control panel) end of the generator. The UNV lugs are protected by a face plate cover that can be secured in the close position by a pad lock. 120 Volt Receptacle One GFCI Duplex NEMA 5-20R (120V, 20 Amp) receptacle is located on the output terminal. This receptacle can be used anytime the generator is in operation. The receptacle is controlled by the circuit breaker located on the control panel.
DCA-60SSAI — OUTPUT TERMINAL VOLTAGE SELECTION DCA-60SSAI NOTE Legs O and Ground are considered Bonded Grounds. Figure 12.
DCA-60SSAI — OUTPUT AMPERAGE SETUP Output Terminal Panel Available Voltages A wide range of voltages are available to supply load to many different applications. Voltages may be selected by using the voltage selector switch and depending how you hookup your hard wire connection to the generator. To obtain some of the voltages listed, fine adjustment with the voltage regulator on the control panel is necessary. See Table 8 for available voltages the generator will supply.
DCA-60SSAI — OUTPUT AMPERAGE SETUP Receptacle Use When the UVWO terminals are providing power, the receptacle power availability will decrease. How To Read The Output Terminal Gauges. The gauges (Figure 15 and 17) and change-over switches on the control panel DO NOT effect the generator output. They are to help observe how much power is being supplied at the UVWO legs.
DCA-60SSAI — OUTPUT VOLTAGE SETUP 240/120V Hard Wire Hookup 480/240V Hard Wire Hookup With the voltage selector set and locked at ‘single phase 240/120’ and using single phase 120 volts, the generator will provide three legs available with 100 amps each on three different circuits (Figure 18). With the voltage selector set and locked at ‘3 phase 480/ 277’ (Figure 19) and using the 3-phase 240 hookup, it will provide one circuit available at 108 amps with any two wires plus the ground (Figure 20).
DCA-60SSAI — OUTPUT VOLTAGE SETUP Voltage Selector Switch- 3 Phase 480/277V Position The following are additional voltages available when the voltage selector switch is in the ‘3 phase 480/277V’ position. Single Phase: 480V, 440V, or 416 Volt This setting can provide single phase power at 480, 440, or 416 volts.
DCA-60SSAI — OUTPUT VOLTAGE SETUP Voltage Selector Switch- 3 Phase 240/139V Position The following are additional voltages available when the voltage selector switch is in the ‘3 phase 240/139V’ position. Figure 25. Voltage Selector Switch 240/139V Three Phase Position Single Phase: 240V, 220V, or 208 Volt This setting can provide single phase power at 240, 220, or 208 volts.
DCA-60SSAI — OUTPUT VOLTAGE SETUP Voltage Selector Switch- Single Phase 240/120V Position The following are additional voltages available when the voltage selector switch is in the ‘single phase 240/120V’ position. Single Phase: 120 Volt This setting can provide single phase power at 120 volts. After hooking up the hard wires to the lugs as shown in Figure 31, 120 volts can be obtained with the voltage regulator knob turned to fine tune. Figure 31. Hard Wire Hookup for Single Phase, 120 volt Figure 29.
DCA-60SSAI — INSTALLATION Outdoor Installation Install the generator in a location where it will not be exposed to rain or sunshine. Make sure the generator is on secure level ground so it cannot slide or shift around. Also install the generator so the exhaust will not be discharged in the direction of nearby homes. The installation site must be relatively free from moisture and dust. All electrical equipment should be protected from excessive moisture.
DCA-60SSAI — INSTALLATION Figure 32.
DCA-60SSAI — PRE-SETUP General Inspection Prior to Operation Circuit Breakers The DCA-60SSAI generator has been thoroughly inspected and accepted prior to shipment from the factory. However, be sure to check for damaged parts or components, or loose nuts and bolts, which could have occurred in transit. Extension Cable To protect the generator from an overload, a 3-pole, 150 amp, main circuit breaker is provided to protect the UNV output terminals from overload.
DCA-60SSAI — PRE-SETUP Lubrication Oil Fill the engine crankcase with lubricating oil through the filler hole, but do not overfill. Make sure the generator is level. With the dipstick inserted all the way, but without being screw into the filler hole, verify that the oil level is maintained between the two notches (Figure 33) on the dipstick. See Table 11 for proper selection of engine oil. Fuel Fill the fuel tank with clean and fresh diesel fuel. DO NOT fill the tank beyond capacity.
DCA-60SSAI — PRE-SETUP CAUTION : When adding coolant or antifreeze to the radiator, do not remove the radiator cap until the unit has completely cooled. Day-to-day addition of coolant is done from the reserve tank. When adding coolant to the radiator, DO NOT remove the radiator cap until the unit has completely cooled. See Table 12. for engine, radiator, and reserve tank coolant capacities. Make sure the coolant level in the reserve tank is always between the "H" and the "L" markings. Table 12.
DCA-60SSAI — PRE-SETUP Battery This unit is of negative ground. DO NOT connect in reverse. Always maintain battery fluid level between the specified marks. Battery life will be shortened, if the fluid level is not properly maintained. Add only distilled water when replenishment is necessary. DO NOT over fill. The battery is sufficiently charged if the specific gravity of the battery fluid is 1.28 (at 68° F). If the specific gravity should fall to 1.
DCA-60SSAI — LOAD APPLICATION Single Phase Load CAUTION: Always be sure to check the nameplate on the generator and equipment to insure the wattage, amperage and frequency requirements are satisfactorily supplied by the generator for operating the equipment. Motors and motor-driven equipment draw much greater current for starting than during operation. Generally, the wattage listed on the nameplate of the equipment is its rated output.
DCA-60SSAI — GENERATOR START-UP PROCEDURE WARNING: The engine's exhaust contains harmful W AY S ventilate the emissions. A LLW exhaust when operating inside tunnels, excavations or buildings. Direct exhaust away from nearby personnel. 2. Connect the load to the UVW terminals as shown in Figure 37. These terminals can be found on the output terminal panel, (see page 22 Figure 6). To gain access to the output terminals lift the UVW cover.
DCA-60SSAI — GENERATOR START-UP PROCEDURE 4. Close all engine enclosure doors (Figure 39). 8. Once the preheat indicator lights, turn the key to ‘START’ (Figure 43). After the engine cranks, release the key to ‘RUN’. Figure 43. Starter Switch (Start) Figure 39. Engine Enclosure Doors 5. Check the voltage selection switch (Figure 40) is at the desired voltage. 9. Pull the engine throttle lever and turn left until the lever sets on the knob (Figure 44). Figure 44. Engine Throttle Lever (Up) Figure 40.
DCA-60SSAI — GENERATOR START-UP PROCEDURE 15. The charging ammeter (Figure 51) will indicate if the battery is properly charged. Figure 47. Voltage Adjust Control Knob 12. The ammeter (Figure 48) will indicate zero amps with no load applied. When a load is applied, this meter will indicate the amount of current that the load is drawing from the generator’s alternator. 20 40 0 Figure 51. Charging Ammeter 16.
DCA-60SSAI — GENERATOR SHUT-DOWN PROCEDURE ENGINE SHUTDOWN To shutdown the generator, use the following procedure: 1. Switch both the MAIN, GFCI and LOAD circuit breakers (Figure 55)to the “OFF” position. EMERGENCY STOP 1. To stop the engine in the event of an emergency, switch the MAIN, GFCI and LOAD circuit breakers to ‘OFF’ position. 2. Turn the key switch to ‘STOP’. Figure 55. Main, GFCI and Load circuit breakers 2. Turn to the right and press in the engine throttle lever (Figure 56). Figure 56.
NOTE PAGE DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01) — PAGE 51
DCA-60SSAI — MAINTENANCE General Inspection Cleaning the Fuel Strainer Prior to each use, the generator should be cleaned and inspected for deficiencies. Check for loose, missing or damaged nuts, bolts or other fasteners. Also check for fuel, oil, and coolant leaks. Clean the fuel strainer if it contains dust or water. Remove dust or water in the strainer cap and wash it in gasoline. Securely fasten the fuel strainer cap so that fuel will not leak.
DCA-60SSAI — MAINTENANCE Feed Pump Strainer Cleaning The strainer is incorporated in the feed pump inlet side joint bolt. Clean the strainer with compressed air and rinse it in the fuel oil. Flushing Out Radiator and Replacing Coolant 1. Open both cocks located at the crankcase side and at the lower part of the radiator and drain coolant. Open the radiator cap while draining. Remove the overflow tank and drain. 2. Check hoses for softening and kinks. Check clamps for signs of leakage. 3.
DCA-60SSAI — MAINTENANCE Valve Clearance Check 1. In order to bring No. 1 or No. 4 cylinder to top dead center in the compression stroke, align the notched line on the crank pulley with TDC mark on the timing gear case cover. 3. Remove the timing check hole cover at the front of injection pump to check the alignment between the pointer “a” on the injection pump gear lock plate and the projected area mark “b” on the timing gear case. 4. If “a” and “b” are in alignment, the timing is set correctly.
DCA-60SSAI — MAINTENANCE INSPECTION / MAINTENANCE ENGINE GENERATOR 10 Hrs DAILY Check Engine Fluid Levels X Check Air Cleaner X Check Battery Acid Level X Check Fan Belt Condition X Check for Leaks X Check for Loosening of Parts X 250 Hrs Replace Engine Oil and Filter *1 X Clean Air Filter X Drain Bottom of Fuel Tank X Clean Unit, Inside and Outside X 500 Hrs Change Fuel Filter *2 X Clean Radiator and Check Coolant Protection Level X 1000 Hrs Replace Air Filter Element X Ch
DCA-60SSAI — GENERATOR WIRING DIAGRAM PAGE 56 — DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01)
DCA-60SSAI — ENGINE WIRING DIAGRAM DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01) — PAGE 57
DCA-60SSAI — TROUBLESHOOTING (ENGINE) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, use the tables shown for diagnosis based on the Engine Troubleshooting (Table 16). If the problem cannot be remedied, consult our company's business office or service plant. TABLE 16. ENGINE TROUBLESHOOTING SYMPTOM Engine does not start. POSSIBLE PROBLEM SOLUTION No fuel? Replenish fuel. Air in the fuel system? Bleed system.
DCA-60SSAI — TROUBLESHOOTING (ENGINE) TABLE 16. ENGINE TROUBLESHOOTING (CONTINUED) SYMPTOM Engine revolution is not smooth. Either white or blue exhaust gas is observed. Either black or dark gray exhaust gas is observed. Deficient output. POSSIBLE PROBLEM SOLUTION Fuel filter clogged or dirty? Clean or change. Air cleaner clogged? Clean or change. Fuel leak due to loose injection pipe retaining nut? Tighten nut. Injection pump malfunctioning? Repair or replace.
DCA-60SSAI — TROUBLESHOOTING (GENERATOR/ENGINE) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, use the tables shown for diagnosis based on the Engine and Radiator Troubleshooting (Table 7). If the problem cannot be remedied, consult our company's business office or service plant. TABLE 17. ENGINE & GENERATOR TROUBLESHOOTING SYMPTOM Engine fails to start and starter does not rotated. Engine fails to start and starter rotates.
NOTE PAGE DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01) — PAGE 61
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
DCA-60SSAI — SUGGESTED SPARE PARTS DCA-60SSAI W/ISUZU 6BD1 DIESEL ENGINE 1 TO 3 UNITS Qty. P/N Description 1 ......... 0601805869 ......... CIRCUIT BREAKER 1 ......... 0601820671 ......... AUTOMATIC VOLTAGE REGULATOR 1 ......... 0601840073 ......... RHEOSTAT VOLTAGE REGULATOR 1 ......... 0601840121 ......... KNOB REHOSTAT 1 ......... 0602013901 ......... RADIATOR HOSE, UPPER 1 ......... 0602013160 ......... RADIATOR HOSE, LOWER 5 ......... 1878100753 ......... OIL FILTER 5 ......... X132400240 ........
DCA-60SSAI --- GENERATOR ASSY. GENERATOR ASSY.
DCA-60SSAI --- GENERATOR ASSY. GENERATOR ASSY. NO. PART NO.
DCA-60SSAI --- GENERATOR ASSY. GENERATOR ASSY.
DCA-60SSAI --- GENERATOR ASSY. GENERATOR ASSY. NO. PART NO. 19 3361350030 19-1 3361352023 19-2 3361362303 20 0041608000 21 0040008000 22 0010008060 23 0040010000 24 0010010030 25 3801312004 26 3331310104 27 0040006000 28 0010006055 29 3361331003 30 0017106010 31 0040010000 32 0010310025 33 3341332103 34 0041606000 35 0040006000 36 0010006030 37 0605000011 38 0040016000 39 0030116000 ITEM FIELD ASSY., EXCITER FIELD CORE, EXCITER FIELD COIL, EXCITER PLAIN WASHER LOCK WASHER HEX. HEAD BOLT LOCK WASHER HEX.
DCA-60SSAI --- CONTROL BOX ASSY. CONTROL BOX ASSY.
DCA-60SSAI --- CONTROL BOX ASSY. CONTROL BOX ASSY. NO. PART NO.
DCA-60SSAI --- CONTROL BOX ASSY. CONTROL BOX ASSY.
DCA-60SSAI --- CONTROL BOX ASSY. CONTROL BOX ASSY. NO. PART NO. 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 0601840031 0601840120 3331824003 0027105016 0030005000 0805001304 0041608000 0030008000 0027105010 7451826504 7451826514 0017106016 0017108020 0030008000 0601815933 0601815934 0027105020 ITEM VOLTAGE REGULATOR KNOB STOPPER, CONTROL PANEL MACHINE SCREW HEX. NUT SET SCREW, CONTROL PANEL PLAIN WASHER HEX. NUT MACHINE SCREW SIDE PANEL, CONTROL BOX SIDE PANEL, CONTROL BOX HEX. HEAD BOLT HEX.
DCA-60SSAI ENGINE AND RADIATOR ASSY. ENGINE AND RADIATOR ASSY.
DCA-60SSAI ENGINE AND RADIATOR ASSY. ENGINE AND RADIATOR ASSY. NO. PART NO. ITEM QTY. REMARKS 1 0602000100 ENGINE ........................................... 1 ......... ISUZU 6BD1 2 0602010802 RADIATOR ....................................... 1 ......... H190110000 3 0602013901 RADIATOR HOSE ........................... 1 ......... B400008 4 0602013160 RADIATOR HOSE ........................... 1 ......... B400007 5 0602014302 HOSE BAND 3 6 0602014303 HOSE BAND 1 7 0602040090 AIR CLEANER .....................
DCA-60SSAI ENGINE AND RADIATOR ASSY. ENGINE AND RADIATOR ASSY.
DCA-60SSAI ENGINE AND RADIATOR ASSY. ENGINE AND RADIATOR ASSY. NO. PART NO. ITEM 31 3362054104 JOINT BOLT 32 3362051003 DRIAN JOINT 33 0802024004 PACKING 34 0802010204 PLUG 35 7452052104 DRAIN HOSE 36 0605515003 HOSE BAND 37 0017108020 HEX. HEAD BOLT 38 0030008000 HEX. NUT 39 0845031303 RESERVE TANK 41 7452082504 BRAKET, RESERVE TANK 42 0017108020 HE. HEAD BOLT 43 0017106025 HEX.
DCA-60SSAI --- ENGINE OPERATING PANEL ASSY. ENGINE OPERATING PANEL ASSY.
DCA-60SSAI --- ENGINE OPERATING PANEL ASSY. ENGINE OPERATING PANEL ASSY. NO. PART NO. ITEM QTY. REMARKS 1 7452111103 OPERATING PANEL 1 2 7452142004 SLIDE BAR 1 ......... UP TO S/N3313037 7452142014 SLIDE BAR 1 ......... S/N3313038~ 3 0805012904 KNOB 1 4 0080200006 SNAP RING 1 ......... UP TO S/N3313037 0036003000 HEX. NUT 1 ......... S/N3313038~ 5 7452140504 BRACKET, GOVERNOR ROD 1 6 0030008000 HEX., NUT 2 7 0605010503 SNAP PIN 1 8 0602100004 STARTER SWITCH 1 .........
DCA-60SSAI --- ENGINE OPERATING PANEL ASSY. ENGINE OPERATING PANEL ASSY.
DCA-60SSAI --- ENGINE OPERATING PANEL ASSY. ENGINE OPERATING PANEL ASSY. NO. PART NO. ITEM QTY. REMARKS 47 0027104016 MACHINE SCREW 2 48 7451860203 SET BOARD, OUTPUT TERMINAL 1 49 0801830204 OUTPUT TERMINAL 4 50 0801830704 HEX. HEAD BOLT 4 51 0041412000 PLAIN WASHER 16 52 0040012000 LOCK WASHER 12 53 0039312000 HEX, .NUT 8 54 0601805318 CIRCUIT BREAKER 1 ......... S/N3312673~;KM52 265V 20A 55 0041608000 PLAIN WSHER 5 56 0040008000 LOCK WASHER 5 57 0010008030 HEX. HEAD BOLT 5 58 0601811032 RECEPTACLE 2 .....
DCA-60SSAI --- BATTERY ASSY. BATTERY ASSY.
DCA-60SSAI --- BATTERY ASSY. BATTERY ASSY. NO. PART NO. 1 0160012100 2 0805003904 3 0805004004 4 0805002904 5 0041608000 6 0040008000 7 0037808000 8 0215260065 9 02511160180 10 0215860100 11 0602220310 0208008000 12 0602220311 0208008000 ITEM QTY. REMARKS BATTERY ......................................... 2 ......... N1000 12V 100Ah BATTERY SHEET 2 BATTERY BAND 2 BATTERY BOLT 4 PLAIN WASHER 4 LOCK WASHER 4 WING NUT 4 BATTERY CABLE 1 BATTERY CABLE 1 BATTERY CABLE 1 TERMINAL ASSY. (+) ......................
DCA-60SSAI --- MUFFLER ASSY. MUFFLER ASSY.
DCA-60SSAI --- MUFFLER ASSY. MUFFLER ASSY. NO. PART NO. 1 7452330103 2 0602320000 3 0602323002 4 3802311122 5 0017110020 6 7452330303 7 3342356104 8 0010108035 9 0041608000 10 0040008000 11 0030008000 12 1382320003 13 0010008030 14 0041608000 15 0030008000 16 3342354104 17 3342354004 18 3342328104 19 0030008000 20 3342359004 21 0017108025 ITEM EXHAUST PIPE GASKET HEX. NUT MUFFLER HEX. HEAD BOLT EXHAUST PIPE GASKET HEX. HEAD BOLT PLAIN WASHER LOCK WASHER HEX. NUT PIPE BAND HEX. HEAD BOLT PLAIN WASHER HEX.
DCA-60SSAI --- FUEL TANK ASSY. FUEL TANK ASSY.
DCA-60SSAI --- FUEL TANK ASSY. FUEL TANK ASSY. NO. PART NO. 1 1-1 1-2 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 7455510123 7455510303 0810105004 0810105400 0802010304 0602021042 7455523104 7455523304 0805003404 0017108020 0041608000 0040008000 0030008000 3805522004 0191300530 0191300650 0605515014 0845032204 0150000018 0802011104 0193100255 0605515079 0131906000 ITEM FUEL TANK FUEL TANK CAP, FUEL TANK FUEL FILTER PACKING PLUG TANK BAND TANK BAND PAD, TANK BAND HEX.
DCA-60SSAI --- ENCLOSURE ASSY. ENCLOSURE ASSY.
DCA-60SSAI --- ENCLOSURE ASSY. ENCLOSURE ASSY. NO. PART NO.
DCA-60SSAI --- ENCLOSURE ASSY. ENCLOSURE ASSY.
DCA-60SSAI --- ENCLOSURE ASSY. ENCLOSURE ASSY. NO. PART NO.
DCA-60SSAI --- RUBBER SEAL ASSY. RUBBER SEAL ASSY.
DCA-60SSAI --- RUBBER SEAL ASSY. RUBBER SEAL ASSY. NO. PART NO.
DCA-60SSAI --- DECALS DECAL ASSY.
DCA-60SSAI --- DECALS DECAL ASSY. NO. PART NO. ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 DECAL; CAUTION ....................................................... 1 ....... B92110050 DECAL; CONTROL PANEL ........................................ 1 ....... B45100590 PLATE; AMMETER CHANGE-OVER SWITCH .......... 1 ....... N2438 PLATE; VOLTAGE CHANGE-OVER SWITCH ........... 1 ....... N2439 DECAL; SAFETY INSTRUCTION ..............................
ISUZU 6BD1 — CYLINDER HEAD COVER ASSY. CYLINDER HEAD COVER ASSY.
ISUZU 6BD1 — CYLINDER HEAD COVER ASSY. CYLINDER HEAD COVER ASSY. NO PART NO PART NAME QTY. REMARKS 1 1111105271 CYLINDER HEAD 1 .......... UP TO AUG. 85; REPLACES 1111105270 1111106141 CYLINDER HEAD 1 .......... AUG. 85~; INCL. ITEMS W/# EA1013 3# 1096000051 REAR SEALING CUP, D=44.5 1 3-1# 9111291280 LOWER SEALING CUP, D=20 3 3-2# 5112190150 EXH. SEALING CUP, D=31.75 3 3-3# 5096000130 DRILLED SEALING CUP, D=12 6 .......... REPLACES 9111296010 3-4# 1096000160 TOP FACE SEALING CUP, D=25 5 3-5# 1096000160 INL.
ISUZU 6BD1 — CYLINDER BLOCK ASSY. CYLINDER BLOCK ASSY.
ISUZU 6BD1 — CYLINDER BLOCK ASSY. CYLINDER BLOCK ASSY. NO. PART NO. PART NAME QTY.
ISUZU 6BD1 — CYLINDER BLOCK ASSY. CYLINDER BLOCK ASSY.
ISUZU 6BD1 — CYLINDER BLOCK ASSY. CYLINDER BLOCK ASSY. NO. PART NO. PART NAME 61 63 64 61-1 65 66 66-1 66-3 67 68 69 96 97& 98 110 9091505080 1093604390 9117426140 1117420211 5093609780 9097130740 9097150670 9099156661 1097040570 0208006250 0208008140 9091505080 8970233390 111 5096230350 5111290030 1112190983 1112191630 9019708180 120 0501408200 8942351570 QTY. REMARKS LOCK WASHER 2 BREATHER COVER HOSE 1 DRAIN PIPE, H=32 ................................................ 1 .......... UP TO MAR.
ISUZU 6BD1 — TIMING GEAR CASE ASSY. TIMING GEAR CASE ASSY.
ISUZU 6BD1 — TIMING GEAR CASE ASSY. TIMING GEAR CASE ASSY. NO. 1 2 3 4 7 8 9 12 13 14 17 18 19 22 PART NO. 5113110113 9081510180 1113120140 0500408450 0500408200 1113210790 1113220360 8943632690 5096250540 1096254380 5113270090 0501408250 5090000841 9091605080 9091505080 5113210090 1112820130 0500406140 PART NAME QTY. REMARKS TIMING GEAR CASE 1 STRAIGHT PIN 1 GEAR PACKING ............................................. 1 .......... REPLACES 1113120100 BOLT ...................................................
ISUZU 6BD1 — FLYWHEEL HOUSING ASSY. FLYWHEEL HOUSING ASSY.
ISUZU 6BD1 — FLYWHEEL HOUSING ASSY. FLYWHEEL HOUSING ASSY. NO. 1 6 7 8 15 41 45 46 47 48 49 PART NO. 9113416098 9992023160 9095714160 9944112350 992023160 0500408250 9910664500 999104140 9096510690 5096250141 1096253620 9123631460 PART NAME QTY. REMARKS FLYWHEEL HOUSING 1 DRAIN PLUG 1 DRAIN PLUG PACKING 1 NUT ................................................................. 3 .......... REPLACES 9944112280 PLUG 1 BOLT ............................................................... 7 ..........
ISUZU 6BD1 —OIL PAN ASSY. OIL PAN ASSY.
ISUZU 6BD1 — OIL PAN ASSY. OIL PAN ASSY. NO 1 3# 4# 6 7 17 20 21 29 32 36 51-2 51-5 52& 53& 53-2 58 59 62 63 PART NO 1113604421 9096620120 1096230570 9992023160 9095714160 1113670961 9992023240 9095714240 0500408180 9112290700 1117602000 5117401102 1117402011 5117410131 1117500060 1117500241 9099129760 9099155531 9091104080 9091505080 PART NAME QTY. REMARKS OIL PAN ...................................... 1 ........ INCL. ITEMS W/# PLUG, M=20 1 PACKING, ID=24 ........................ 1 ........
ISUZU 6BD1 — OIL PUMP ASSY. OIL PUMP ASSY.
ISUZU 6BD1 — OIL PUMP ASSY. OIL PUMP ASSY. NO. 1 1-2 2#& 4#&$ 6#& 8#& 9# 11# 12# 13# 14# 16# 16-2# 17# 18#& 19#& 21#& 22#& 23#& 24#& 26#& 36#& 41 43 PART NO. 5131000913 1131002330 1131130470 1131190030 5131210050 5131250010 5131190020 9095612230 1131410210 1131190020 5131410020 9098010741 1090440470 9091505080 5098430030 5095800980 5131650040 9081040300 1131230160 1131280180 9131190100 1131400860 0500410250 9131190100 PART NAME QTY. REMARKS OIL PUMP ...................................... 1 ...........
ISUZU 6BD1 — CRANKSHAFT ASSY. CRANKSHAFT ASSY.
ISUZU 6BD1 — CRANKSHAFT ASSY. CRANKSHAFT ASSY. NO. 1 1-1 1-2 2# 3 4 6 7 8 9& 11& 13 13-1 13-2 14 17$ 19 26 27 33 34 36 37 38 60 67 81 83 PART NO.
ISUZU 6BD1 — CAMSHAFT, IDLE GEAR, ROCKER ARM ASSY. CAMSHAFT, IDLE GEAR, ROCKER ARM ASSY.
ISUZU 6BD1 — CAMSHAFT, IDLE GEAR, ROCKER ARM ASSY. CAMSHAFT, IDLE GEAR, ROCKER ARM ASSY. NO. 1 6 7 8 9 11 12 21 22 24 26 27 31 32 33 35 36 38 43 44 51 53 54 56-1 56-2 57 58 58-1 58-2 59 60 61 62 64 64-1 66 67 68 PART NO.
ISUZU 6BD1 — OIL AND FUEL FILTER ASSY. OIL AND FUEL FILTER ASSY.
ISUZU 6BD1 — OIL AND FUEL FILTER ASSY. OIL AND FUEL FILTER ASSY. NO. 1 2# 3#& 4# 5# 6# 8# 9# 12# 16# 17# 21# 28# 29#$ 70 72 PART NO.
ISUZU 6BD1 — OIL AND AIR PIPE ASSY. OIL AND AIR PIPE ASSY.
ISUZU 6BD1 — OIL AND AIR PIPE ASSY. OIL AND AIR PIPE ASSY. NO. 1 2 3 4 6 7 9 10# 11 12 PART NO. 5133110890 133115322 9099211880 0500408400 5133111190 1096232820 1096234620 0500408400 5133112050 9099171050 1096308830 9098440220 PART NAME QTY. REMARKS OIL PUMP ASSY. ................. 1 ..................... UP TO MAR. 84 OIL PUMP ASSY. ................. 1 ..................... APR. 4~ PACKING 2 BOLT .................................... 4 ..................... REPLACES 9019108400 COOLER PIPE ASSY. 1 O RING .
ISUZU 6BD1 — COOLING SYSTEM ASSY. COOLING SYSTEM ASSY.
ISUZU 6BD1 — COOLING SYSTEM ASSY. COOLING SYSTEM ASSY. NO. 1 2# 3#% 4#% 6#% 6-1#% 7#% 8#% 9#% 11#% 12#% 13#% 16#% 17#% 18#% 20#% 21#% 22#% 31% 33 33-1 41 50 51 52 53 54 59 61 62 64 68 71 72 73 74 75 PART NO.
ISUZU 6BD1 — COOLING SYSTEM ASSY. COOLING SYSTEM ASSY.
ISUZU 6BD1 — COOLING SYSTEM ASSY. COOLING SYSTEM ASSY. NO. 76 77 79 80 91 92 92-1 93 94 106 107 119 120 121@ 122@ 123@ 124@ 125@ 126@ 127@ 128@ 129@ 130@ 141 142 142-1 144 PART NO.
ISUZU 6BD1 — INTAKE AND EXHAUST ASSY. INTAKE AND EXHAUST ASSY.
ISUZU 6BD1 — INTAKE AND EXHAUST ASSY. INTAKE AND EXHAUST ASSY. NO. 1 3 4 20 20-1# 21 22 24 27 30 30-1 31 32 32-1 33 33-1 34 34-1 46 48 49 50 51 76 76-1 77 78 83 86 PART NO.
ISUZU 6BD1 — FUEL SYSTEM ASSY. FUEL SYSTEM ASSY.
ISUZU 6BD1 — FUEL SYSTEM ASSY. FUEL SYSTEM ASSY. NO. 1 11 12 13 14 15 16 17 18 19 20 21 22 23 24 31 32 33 34 35 36 37 38 39 39-1 41-5 41-6 43 47 48 49 54 56 PART NO.
ISUZU 6BD1 — ENGINE FOOT AND HANGER ASSY. ENGINE FOOT AND HANGER ASSY.
ISUZU 6BD1 — ENGINE FOOT AND HANGER ASSY. ENGINE FOOT AND HANGER ASSY. NO. 8 11 13 13-1 15 16 17 18 19 31 32 35 36 37 38 41 42 42-1 42-2 43 51 52 55 56 62 63 64 80 81 82 83 84 85 87 PART NO.
ISUZU 6BD1 — INJECTION PUMP ASSY. INJECTION PUMP ASSY.
ISUZU 6BD1 — INJECTION PUMP ASSY. INJECTION PUMP ASSY. NO. 5 PART NO. 1156020451 1156026800 1157203470 1157704760 20# 1157500480 36# 5157810030 37# 1197510400 38# 9884105020 39# 5156190480 40# 9096620070 41# 1095390070 41-2# 1156192450 42# 5125240570 43# 9019006140 15# PART NAME QTY. REMARKS INJECTION PUMP ASSY. ......... 1 ................ UP TO NOV. 89; REPLACES 1156010605 INCL. ITEMS W/# INJECTION PUMP ASSY. ......... 1 ................ DEC. 89~ GOVERNOR ASSY. ................... 1 ................
ISUZU 6BD1 — ELECTRICAL ASSY. ELECTRICAL ASSY.
ISUZU 6BD1 — ELECTRICAL ASSY. ELECTRICAL ASSY. NO. 3 7 22 23# 24# 29 30 31 32& 33& 37 40 64 65 65-1 67 82 82-1 83% 109 PART NO. 1811001910 1812002050 5831510030 9827200690 9099022380 9831514320 1823200010 1823100080 1823130030 1823170070 5824500141 1825500732 9825139288 5197320010 5197320020 9825300430 1819000161 1819001931 1828490430 9829322110 PART NAME QTY. REMARKS STARTER 1 ALTERNATOR 1 OIL PRESSURE SWITCH ADAPTER ...1 ............... INCL. ITEMS W/# OIL PRESSURE WARNING SW.
ISUZU 6BD1 — INJ. PUMP COMP. ASSY. INJECTION PUMP COMP. ASSY.
ISUZU 6BD1 — INJ. PUMP COMP. ASSY. INJECTION PUMP COMP. ASSY. NO. 5 14 15 16 18 20 22 23 24 27 28 29 31 32 34 35 36 40 41 43 45# 47# 48# 49# 55 PART NO.
ISUZU 6BD1 — INJ. PUMP COMP. ASSY. INJECTION PUMP COMP. ASSY.
ISUZU 6BD1 — INJ. PUMP COMP. ASSY. INJECTION PUMP COMP. ASSY. NO. 58 59 60 61 62 66 67 75-3 75-4 76 77 82 83 84 PART NO.
ISUZU 6BD1 — INJ. PUMP COMP. ASSY. INJECTION PUMP COMP. ASSY.
ISUZU 6BD1 — INJ. PUMP COMP. ASSY. INJECTION PUMP COMP. ASSY. NO. 87 88 89 93 95 108 150 162 163 164 180 181 182 183 PART NO. 1156190330 9884100660 9812250430 1156290470 1156192820 5835390240 5156191360 9091606100 9091506100 5156390020 1156192660 1156290490 9041010300 1156290480 PART NAME BEARING SCREW WASHER COVER BOLT WOODRUFF KEY PLUB WASHER WASHER NUT BRACKET PACKING STUD GASKET QTY.
ISUZU 6BD1 — GOVERNOR COMP. ASSY. GOVERNOR COMP. ASSY.
ISUZU 6BD1 — GOVERNOR COMP. ASSY. GOVERNOR COMP. ASSY. NO. 5 12# 13# 14# 15# 16# 18# 19# 50# 26# 27# 30# 31# 32# 34# 35# 36# 37# 38# 40# 42# 44# 46# 47# 48# 50# 52# 53# 54# 57# 58# 60# 63# 64# 67# 68# 69# 73# 74# 77# 80# 81# 82# PART NO.
ISUZU 6BD1 — GOVERNOR COMP. ASSY. GOVERNOR COMP. ASSY.
ISUZU 6BD1 — GOVERNOR COMP. ASSY. GOVERNOR COMP. ASSY. NO. PART NO. PART NAME QTY.
ISUZU 6BD1 —FEED PUMP ASSY. FEED PUMP ASSY.
ISUZU 6BD1 — FEED PUMP ASSY. FEED PUMP ASSY. NO. PART NO. 1157500480 5# 5157510120 9# 9813512050 10# 9813513020 11# 9813550230 12# 9813550350 15# 5157540010 16#% 9813514030 17#% 9813514100 18#% 1157590020 26# 9813516020 27# 1196230160 28# 9813517020 31# 1096750630 32# 1157590110 33# 1157590120 35# 1157590030 40# 1196230160 42# 9813550250 44# 8941311300 PART NAME QTY. REMARKS FEED PUMP ASSY. ....................... 1 .................. INCL. ITEMS W# HOUSING 1 PISTON 1 SPRING 1 PLUG 1 GASKET 1 TAPPET ASSY.
ISUZU 6BD1 — NOZZLE ASSY. NOZZLE ASSY.
ISUZU 6BD1 — NOZZLE ASSY. NOZZLE ASSY. NO. 1 2 PART NO. 5153110191 5153300191 5# 6# 7# 8# 9# 10# 12# 21# 22# 23# 31# 32# 5153410010 9153470030 9153430130 5153450010 9153390570 5153340010 9153390560 5153320020 5153390030 5153490020 5153490010 9095714080 PART NAME QTY. REMARKS NOZZLE ASSY. ......................... 6 ................ REPLACES 5153110190 HOLDER ASSY. ........................ 6 ................ REPLACES 5153300190; INCL.
ISUZU 6BD1 — STARTER ASSY, STARTER ASSY.
ISUZU 6BD1 — STARTER ASSY. STARTER ASSY. NO. PART NO.
ISUZU 6BD1 — ALTERNATOR ASSY. ALTERNATOR ASSY.
ISUZU 6BD1 — ALTERNATOR ASSY. ALTERNATOR ASSY. NO. 5# 7# 8# 9# 10# 11# 12# 13# 14# 15# 16# 16-1# 17# 18# 19# 20# 25# 26#@ 27#@ 33#@ 40#@ 41#@ 43#@ 45#@ 51# 52# 55# 56# 60# 61# 62# 63# 75# 90# 95# 97# 99# PART NO.
ISUZU 6BD1 — ACCESSORIES ACCESSORIES PAGE 148 — DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01)
ISUZU 6BD1 — ACCESSORIES ACCESSORIES NO. 50 55 60 PART NO. 9839101011 1096231800 1096234650 0500408200 PART NAME QTY. REMARKS TACHO DRIVE ELBOW ASSY. . 1 PACKING ................................... 1 ................. UP TO OCT. 87 PACKING ................................... 1 ................. NOV. 87~ BOLT ......................................... 2 .................
TERMS AND CONDITIONS OF SALE — PARTS Effective: July 1, 2000 4. PAYMENT TERMS Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier. Freight is at the sender’s expense.
NOTE PAGE DCA-60SSAI — PARTS AND OPERATION MANUAL— FINAL COPY (09/15/01) — PAGE 151
PARTS AND OPERATION MANUAL PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING © COPYRIGHT 2001, MULTIQUIP INC.
