OPERATION AND PARTS MANUAL MODEL MS-70 PLASTER AND MORTAR MIXER (GASOLINE ENGINE/ELECTRIC MOTOR) Revision #3 (03/26/10) THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND Post Office Box 6254 Carson, Ca 90749 888-252-STOW FAX: 800-427-1244 310-537-3700 FAX: 800-672-7877 FAX: 310-637-3284 800-421-1244 310-537-3700 FAX: 310-537-4259 800-478-1244 FAX: 310-631-5032 800-421-1244, EXT. 279 310-537-3700, EXT.
STOW MS-70 PLASTER/MORTAR MIXER — TABLE OF CONTENTS STOW MS-70 — Plaster/Mortar Mixer HONDA GX240K1HA2 ENGINE Terms and Conditions of Sale — Parts .................. 92 Component Drawings NOTE PAGE 4 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ ❒ ❒ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: ✓ FedEx or UPS Ground Note: Unless otherwise indicated by customer, all ✓ FedEx or UPS Second Day or Third Day orders are treated as “Standard Orders”, and will
STOW MS-70 PLASTER/MORTAR MIXER — SPECIFICATIONS TABLE 1. MIXER SPECIFICATIONS Capacity 7.0 cu. ft (198 liters) Bag Capacity 1-1/2 to 2-1/2 bags Weight 788 lbs. (357 kg.) Height W/Dump Handle 73 in. (185 cm.) Discharge Height 21 in. (53 cm.) Drive V-Belt/Gear Dump Action Manual Table 2. Specifications (Engine & Electric Motor) Model Type Engine/Electric Motor 1.5 HP, 115/230, Single Phase Electric Motor N/A Displacement 14.81 cc N/A 8.0 H.P./3600 R.P.M. 1.5 H.P./1725 RPM Approx. 1.
STOW MS-70 PLASTER/MORTAR MIXER — DIMENSIONS TABLE 3. DIMENSIONS Description Dimensions in. (cm) Length (w/ Tow Bar) 67 in. (170 cm) Width 50 in. (127 cm) Height 56 in. (142 cm) Figure 1. Dimensions STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! HAZARD SYMBOLS Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. WARNING This Owner's Manual has been developed to provide complete instructions for the safe and efficient operation of the STOW Model MS-70 mortar and plaster mixer.
STOW MS-70 MIXER — SAFETY MESSAGE ALERT SYMBOLS CAUTION Rotating Parts Hazards CAUTION Equipment Damage Hazards NEVER CAUTION Accidental Starting Hazards ALWAYS ON/OFF OFF CAUTION Eye and Hearing Hazards ALWAYS STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 PLASTER/MORTAR MIXER — RULES FOR SAFE OPERATION DANGER Read this manual! ■ NEVER ■ High Temperatures GENERAL SAFETY ■ DO NOT ■ ■ ■ NEVER ■ ALWAYS ■ NEVER ■ ALWAYS flammable stop the DO NOT ■ NEVER ■ NEVER ■ ALWAYS ■ NEVER ■ ■ ■ NEVER . ■ ■ ■ ■ WARNING Starting the Mixer Engine NEVER PAGE 10 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 PLASTER/MORTAR MIXER — RULES FOR SAFE OPERATION ■ ALWAYS TRANSPORTING ■ NEVER ■ ALWAYS ■ ■ ALWAYS ■ ■ ALWAYS MAINTENANCE ■ NEVER ■ ALWAYS ■ ALWAYS ■ ALWAYS ■ DO NOT ■ ■ ■ CAUTION ■ ■ ■ DO NOT ■ EMERGENCIES ■ ALWAYS ■ first aid kit. ■ ■ ■ NEVER ■ WARNING Stand Clear of the Mixer when in use ■ ■ STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 PLASTER/MORTAR MIXER — TOWING GUIDELINES Towing Safety Precautions CAUTION Regularly Inspect Towing Components ■ ALWAYS OFF ■ torque wrench ■ ■ ■ ■ Tow Bar to Vehicle Connection (Coupler Only) ■ ■ ALWAYS NEVER CAUTION Replacing Towing Components ■ CHECK NEVER ■ ALWAYS Chain Safety ■ ALWAYS ■ ALWAYS ■ 55 10 15 MPH Mixer Tow Bar Vehicle Connection (Pintle and Loop) ■ chocked blocks , ■ ■ PAGE 12 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 PLASTER/MORTAR MIXER — SAFETY CHAIN CONNECTION CAUTION Always Tow with a Safety Chain NEVER! Tow Bar to Mixer Connection Drum Saftey when Towing CAUTION DO NOT right Figure 3. Drum Latch Pin (Tow or Locked Position) Figure 2. Tow Bar and Safety Chain Installation STOW MS-70 MIXER — OPERATION MANUAL — REV.
MS-70 PLASTER/MORTAR MIXER — OPERATION AND SAFETY DECALS Machine Safety Decals The STOW MS-70 mortar and plaster mixer is equipped with a number of safety decals. These decals are provided for operator safety and maintenance information. Figure 4 below illustrates these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer. Figure 4. Mixer Operation and Safety Decals PAGE 14 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 PLASTER/MORTAR MIXER — GENERAL INFORMATION Application The STOW MS-70 series mixers (drum capacity of 7.0 cu. ft./198 liters) are shipped completely assembled and have been factory tested and are ready for use. This mixer is Hardware Power Plants STOW gasoline engine or a 1.5 HP electric motor. Refer to Table 2 for specific engine or electric motor data information. Table 4.
STOW MS-70 PLASTER/MORTAR MIXER — BASIC MIXER COMPONENTS 8. Mixing Paddles — Used in the mixing of material. This unit uses four different types of paddles to provide a fast uniform mix. 9. Bag Cutter— This feature allows compound mixing bags to be opened easily, therefore allowing the contents of the bag to fall directly into the mixing drum. 10. Safety Grill — Provided for operator safety. This safety grill is designed to keep hands and solid objects out of the mixing drum when in use.
STOW MS-70 PLASTER/MORTAR MIXER — BASIC ENGINE COMPONENTS Figure 6. Engine Controls and Components INITIAL SERVICING 5. The engine (Figure 6) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers Engine manual for instructions & details of operation and servicing. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop the flow of fuel. 6. Choke Lever – Used in the starting of a cold engine, or in cold weather conditions.
STOW MS-70 PLASTER/MORTAR MIXER — ELECTRIC MOTOR Electric Motor TABLE 5. ELECTRIC MOTOR WIRING INFORMATION Motor Horsepower Rating Electric Motor Safety CAUTION 115-230 VAC - Single Phase NEMA Plug Connector Mating NEMA Receptacle Connector 1.5 HP (115 VAC) L5-20P P/N EM940537 L5-20R P/N EM940538 1.
STOW MS-70 PLASTER/MORTAR MIXER — ELECTRIC MOTOR The motor supplied is wired for 115 VAC grounded operation. Make certain that the correct size grounded (3-wires) extension cord is used. See Table 6. Motors can burn out when the line voltage falls 10% below the voltage rating of the motor. Failure to use proper voltage will cause the motor to overheat and actuate the overload switch. TABLE 6. RECOMMENDED EXTENSION CORD SIZES Model Motor Voltage WM-70 1.5 HP (Electric) 50 ft. 75 ft. (15.24 m) (22.
STOW MS-70 — PADDLE BLADE ADJUSTMENT (STEEL DRUM) Adjust paddles as shown in Figure 8. Figure 8. Paddle Blade Adjustment, Steel Drum PAGE 20 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 PLASTER/MORTAR MIXER — INSPECTION 3. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. Before Starting 4. If the oil level is low (Figure 10), fill to the edge of the oil filler hole with the recommended oil type (Table 7). Maximum oil capacity is 2.33 qts. (1.09 liters) NOTE CAUTION Eyesight and Hearing Protection ALWAYS CAUTION Inspection & Maintenance Saftey NEVER Figure 10.
STOW MS-70 PLASTER/MORTAR MIXER — INSPECTION V-belt Check Fuel Check DANGER Explosive Fuel Hazard Blade Check DO NOT DO NOT 1. Remove the gasoline cap located on top of fuel tank. 2. Visually inspect to see if fuel level is low. If fuel is low, replenish with unleaded fuel. Controls Start/Stop Switches 3. When refueling, be sure to use a strainer for filtration. DO NOT top-off fuel. Wipe up any spilled fuel. CAUTION Start/Stop Switch NEVER! disable or disconnect the start/stop switch.
STOW MS-70 PLASTER/MORTAR MIXER — START-UP PROCEDURES This section is intended to assist the operator with the initial start-up of the STOW MS-70H (gasoline engine) or STOW MS-70E (electric motor) mixer. It is extremely important that this section be read carefully before attempting to use the mixer in the field. 2. To start a cold engine, move the choke lever (Figure 12) to the CLOSED position. DO NOT use your mixer until this section is thoroughly understood. WARNING General Safety 3.
MS-70 PLASTER/MORTAR MIXER — START-UP PROCEDURES 4. Turn the engine switch (Figure 14) to the ON position. CAUTION Preventing Drum Tipping Make certain the drum lock pin (Figures 17 and 18) is placed to the RIGHT (when viewing the mixer from the towpole end) of the drum stop block which is welded to the front side of the drum. Also make sure lock pin is fully engaged (locked). This will prevent the drum from tipping. Figure 14. Engine ON/OFF Switch 5.
STOW MS-70 PLASTER/MORTAR MIXER — OPERATION/SHUT-DOWN 8. Place the belt slip lever (Figure 20) in the mix position. This will tilt the engine placing tension on the V-belts enabling the shaft to rotate. WARNING Dump Handle Safety Be sure to stand clear of the dump handle (Figure 22) when the mixer is operational. Any binding of material between the mixer blades and the drum will cause the drum handle to move to the discharge position and could cause bodily harm. Figure 20.
STOW MS-70 PLASTER/MORTAR MIXER — MAINTENANCE (ENGINE) Use Table 8 as a general maintenance guideline when servicing your engine. For more detail engine maintenance information, refer to the engine owner's manual supplied with your engine. Table 8. Engine Maintenance Schedule DESCRIPTION (3) OPERATION BEFORE CHECK X FIRST EVERY MONTH 3 MONTHS OR OR 10 HRS. 25 HRS. EVERY 6 MONTHS OR 50 HRS. EVERY YEAR OR 100 HRS. EVERY 2 YEARS OR 200 HRS.
STOW MS-70 PLASTER/MORTAR MIXER — MAINTENANCE (ENGINE) Maintenance Perform the scheduled maintenance procedures as defined by Table 8 and below: DAILY ■ Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. Check the gearbox for oil leaks. Repair or replace as needed. WEEKLY ■ Remove the fuel filter cap and clean the inside of the fuel tank.
STOW MS-70 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER) Ball Socket and Clamp Face Maintenance 1. 2. 3. If the towing vechicle is equipped with a ball socket, smear socket periodically with multi-purpose grease. This will keep the ball socket well lubricated. Periodically oil pivot points and clamp face surfaces of coupler with SAE 30 WT. motor oil. When parking or storing your mixer. Keep the coupler off the ground so dirt will not build up in the ball socket.
STOW MS-70 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER) 2. Fill the wheel hub (Figure 28) with grease to the inside diameter of the outer races and also fill the hub grease cap. Reassemble the hub and mount the wheel. Then tighten the adjusting nut, at the same time turn the wheel in both directions, until there is a slight bind to be sure all the bearing surfaces are in contact.
STOW MS-70 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER) Grease Fittings (Zerk) Maintenance (Electric Motor) 1. 2. There are two grease (Figure 33) fittings at each end of the electric motor that will require lubrication. Lubricate these fittings about every 16 months. Use Poleyrex EM (Exxon Mobil) or equalivant lubricant. Clean grease fitting, apply grease gun to fitting (1/2 shot). Remember too much grease or injecting grease too quickly can cause premature bearing failure.
STOW MS-70 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER) 3. After first road use, retorque all lug nuts in sequence. Check all wheel lug nuts periodically. Lug Nut Torque Requirements 1. Start all wheel lug nuts by hand. 2. Torque all lug nuts in sequence. See Figure 34. DO NOT torque the wheel lug nuts all the way down.Tighten each lug nut in 3 separate passes as defined by Table 10. Table 10.
STOW MS-70 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER) Suspension Keep Hands Clear of Drum! When rotating the mixing drum from the dump position to the upright position, keep hands clear of safety grate. The possibility exists of hands or fingers being crushed (Figure 37). WARNING Figure 35. Axle Support Components Mixer Cleaning 1. ALWAYS disconnect the spark plug wire (gasoline engines) before cleaning the inside of the drum.
STOW MS-70 PLASTER/MORTAR MIXER — TROUBLESHOOTING (ENGINE) TABLE 11. ENGINE TROUBLESHOOTING SYMPTOM Poor star ting Insufficient power output "no compression" Insufficient power output "compression" POSSIBLE PROBLEM SOLUTION Inspect carburetor to see if fuel is reaching it? Check fuel line No Fuel? Add Fuel Water in fuel tank? Flush or replace fuel tank. Fuel filter clogged? Replace fuel filter Stuck carburetor? Check float mechanism. Spark plug is red? Spark plug is fouled.
STOW MS-70 PLASTER/MORTAR MIXER — TROUBLESHOOTING (ENGINE) TABLE 11. ENGINE TROUBLESHOOTING (CONTINUED) SYMPTOM POSSIBLE PROBLEM Insufficient power output "compression" and overheats Burns to much fuel Exhaust color is continiously "WHITE" Exhaust color is continiously "BLACK" SOLUTION Malfunction in cooling fan? Check or replace cooling fan. Air in-take filter clogged? Clean or replace air in-take filter. Over accumulation of exhaust products? Clean and check valves.
STOW MS-70 — TROUBLESHOOTING (MIXER/ELECTRIC MOTOR) TABLE 12. MIXER TROUBLESHOOTING SYMPTOM POSSIBLE PROBLEM SOLUTION Worn or defective V-belt? Replace V-belt. Adjustment lever mis-aligned? Check position of adjustment lever. Adjust if necessary. Worn or defective paddle shaft seals? Replace seals. Defective or worn drum suppor t brackets? Apply grease to bracket or replace. Blades adjusted too tight. Adjust blades until they almost touch side walls of drum. Blades will not rotate.
STOW MS-70 MIXER — WIRING DIAGRAM (ELECTRIC MOTOR) Figure 24. Electric Motor Wiring Diagram PAGE 36 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
NOTE PAGE STOW MS-70 MIXER — OPERATION MANUAL — REV.
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Items Found In the “Remarks” Column NOTE The contents of this parts catalog are subject to change without notice. Items Found In the “Items Number” Column All parts with same symbol in the number column, , #, +, %, or * >, belong to the same assembly or kit. NOTE If more than one of the same reference number is listed, the last one listed indicates newest (or latest) part available.
STOW MS-70 MIXER — SUGGESTED SPARE PARTS MS-70P/S PLASTER AND MORTAR MIXER 1 TO 3 UNITS WITH HONDA GX160K1HX2 AND GX240K1HA2 ENGINES NOTE Qty. ... P/N ...................... Description 6 ....... 07055-034 ........... V-BELT A34 HONDA ENGINE 6 ....... 491112 ................ V-BELT A40 ELECTRIC MOTOR 2 ....... EM914288 ........... OIL SEAL, AXLE 4 ....... EM903113 ........... BEARING, CONE, AXLE 4 ....... EM903112 ........... BEARING, CUP, AXLE 2 ....... 20654-001 ........... SEAL, PADDLE SHAFT (BLACK) 2 ..
STOW MS-70 MIXER — NAMEPLATE AND DECALS PAGE 40 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — NAMEPLATE AND DECALS NO PART NO PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — FRAME ASSY. PAGE 42 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — FRAME ASSY. NO. * 14 * 14 * 14A * 15 16 17 18 PART NO. PART NAME QTY. REMARKS 01004 01004 516580 13363KIT HBC-1 HLC-1 HPC-1 SAFETY CHAIN 1 CONNECTOR LINK ..................................................... 2 .............. BEFORE JANUARY 2006 CONNECTOR LINK ..................................................... 1 .............. AFTER JANUARY 2006 CLEVIS SAFETY HOOK ............................................ 1 .............. AFTER JANUARY 2006 CHAIN AND LINK KIT ................
STOW MS-70 MIXER — PADDLE SHAFT ASSY. PAGE 44 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — PADDLE SHAFT ASSY. NO. PART NO. PART NAME QTY. REMARKS * 11 * 12 * 13 * 14 * 15 * 16 17 * 18 * 19 492367 EM923023 EM202929 EM202899 2105164 EM923343 EM202899 EM202927 EM202926 EM203010 SCREW, HHC 5/16-18 X 1-3/4 G5 14 WASHER, FLAT 5/16" 28 BLADE, SIDE, RUBBER 4 BLADE, SIDE, SCRAPPER 4 NUT, HEX 5/16" NC G5 14 WASHER, LOCK 5/15" 14 PADDLE ARM, TOW END 1 BLADE ,SCRAPPER END 2 BLADE, RUBBER END 2 KIT, WIPERS, SCRAPPERS & HDWARE ................... 1 ...................
STOW MS-70 MIXER — STEEL DRUM ASSY. 24 23 22 20 20 20 29 21 26 25 20 28 27 4 11 5 12 13 6 1 3 15 13 7 9 11 8 17 1 10 5 15 31 9 4 14 30 3 6 7 6 8 10 12 1 2 19 18 18 PART OF REAR FRAME PART OF FRONT FRAME NOTES: SET SCREWS AND BEARING 1 COLLAR ARE INCLUDED WITH BEARING AND CANNOT BE PURCHASED SEPARATELY. PAGE 46 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — STEEL DRUM ASSY. NO. PART NO. PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY. PAGE 48 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY. NO. PART NO. PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — AXLE ASSY. PAGE 50 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — AXLE ASSY. NO # 2# 3 4 5 6 7 8# 9# 10# 11 12 PART NO 3469 8115 3005 8164 491688 EM511159 EM501299 EM903113 EM903012 EM914288 EM941306 514802 PART NAME QTY. REMARK DUST CAP 2 LUG NUTS 8 TIRE AND RIM, CARLISE 2 CASTLE NUT 1" 2 COTTER PIN 1/8" X 1-1/2' 2 WASHER, FLAT, .087" THICKNESS 2 WASHER, FLAT, .135" THICKNESS 1 BEARING CONE 4 BEARING CUP 4 OIL SEAL 2 HUB ASSY., 4-BOLT ....................................................... 2 ...........
STOW MS-70 MIXER — ENGINE ASSY. PAGE 52 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — ENGINE ASSY. NO PART NO PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — ELECTRIC MOTOR ASSY. ELECTRIC MOTOR ASSY. PAGE 54 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — ELECTRIC MOTOR ASSY. ELECTRIC MOTOR ASSY. NO PART NO PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — CABINET ASSY. PAGE 56 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
STOW MS-70 MIXER — CABINET ASSY. NO PART NO PART NAME QTY. REMARKS 2 3 4 5 6 * 7 8 9 10 11 12 13 14 490202 13287 2203 1307 491010 492375 492598 492583 29174-001 29173-001 504135C RAL1003S RAL1003G RUBBER PROTECTOR 4 LOCK NUT 8-32 ........................................... 6 ........... REPLACEMENT PART ONLY WASHER, FLAT #10 .................................... 6 ........... REPLACEMENT PART ONLY SCREW RHMS 8-32 X 1/2" ......................... 6 ........... REPLACEMENT PART ONLY LATCH ASSY.
HONDA GX240K1HA2 ENGINE — AIR CLEANER ASSY. PAGE 58 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — AIR CLEANER ASSY. NO. PART NO. PART NAME QTY. REMARKS 2 3 * 5 6 8# 9# 10 12 13 14 15 17210ZE2515 17218ZE2505 17231ZH9820 17232891000 17238ZE2310 17239ZE1000 17410ZE2020 0037806000 90325044000 90009ZE2003 9405006000 ELEMENT, AIR CLEANER, DUAL 1 FILTER, OUTER 1 COVER, AIR CLEANER 1 GROMMET, AIR CLEANER 1 COLLAR, AIR CLEANER 2 COLLAR B, AIR CLEANER 1 ELBOW COMP., AIR CLEANER ............... 1 .............
HONDA GX240K1HA2 ENGINE — CAMSHAFT ASSY. PAGE 60 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — CAMSHAFT ASSY. NO. PART NO. PART NAME 1 2 3 4 5 6 * 7 8 9 10 11 12 13 14 15 14100ZE2306 14410ZE2013 14431ZE2010 14441ZE2000 14451ZE1013 14568ZE1000 14711ZE2000 14721ZE2000 14751ZE2003 14771ZE2000 14773ZE2000 14781ZE2000 14791ZE2010 90012ZE0010 90206ZE1000 CAMSHAFT ROD PUSH ARM VALVE ROCKER LIFTER VALVE PIVOT ROCKER ARM SPRING, WEIGHT RETURN VALVE, IN. VALVE, EX. SPRING, VALVE RETAINER, IN. VALVE SPRING RETAINER, EX.
HONDA GX240K1HA2 ENGINE — CARBURETOR ASSY. PAGE 62 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — CARBURETOR ASSY. NO. *+ 2 * 3 * 5 * 6 + * 7 + * 8 * 9 * 10 * 11 * 12 * 13 * 14 15 16 17 18 19 * 20 * 21 * 22 * 23 * 24 * 25 26 * 26 * 26 * 27 * 28 * PART NO.
HONDA GX240K1HA2 ENGINE — CONTROL ASSY. PAGE 64 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — CONTROL ASSY. NO. PART NO. PART NAME QTY. REMARKS * * * * * * * * * STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — CRANKCASE COVER ASSY. PAGE 66 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — CRANKCASE COVER ASSY. NO. PART NO. PART NAME QTY. REMARKS * # % 8% 9# 15625ZE1003 GASKET, OIL FILLER CAP 1 WEIGHT, GOVERNOR HOLDER, GOVERNOR WEIGHT PIN, GOVERNOR WEIGHT 2 1 2 + 11 + 16511ZE2000 * 12 + 16512ZE2811 * 13 + 16513ZE2000 * 14 * * * * * * * * STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2ENGINE — CRANKSHAFT ASSY. PAGE 68 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2ENGINE — CRANKSHAFT ASSY. NO. PART NO. PART NAME QTY. REMARKS * * STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — CYLINDER BARREL ASSY. PAGE 70 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — CYLINDER BARREL ASSY. NO. PART NO. PART NAME 2 3 6 7 8 * 9 10 11 12 13 14 * 15 16 15510ZE2043 16541ZE2010 90131896650 90446KE1000 91201890003 91353671003 9405010000 031112230 9425110000 957010601200 961006202000 90013883000 34150ZH7003 SWITCH ASSY., OIL LEVEL SHAFT, GOVERNOR ARM BOLT, DRAIN PLUG WASHER 8.2 X17X0.
HONDA GX240K1HA2 ENGINE — CYLINDER HEAD ASSY. PAGE 72 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — CYLINDER HEAD ASSY. NO. PART NO. PART NAME 2 * 3 * 4 * 5 6 7 8 10 11 12 13 14 15 16 17 17 12204ZE2306 12205ZE2305 12216ZE2300 12251ZE2800 12310ZE2020 12391ZE2020 14775ZE2010 90014ZE2000 90042ZE2000 92900080320E 90441ZE2010 9430112200 950051100130M 957011008000 9807956846 9807956855 GUIDE, VALVE, OS, OPTIONAL GUIDE, EX. VALVE, OS, OPTIONAL CLIP, VALVE GUIDE GASKET, CYLINDER HEAD COVER COMP.
HONDA GX240K1HA2 ENGINE — FAN COVER ASSY. PAGE 74 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — FAN COVER ASSY. NO. PART NO. PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — FLYWHEEL ASSY. PAGE 76 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — FLYWHEEL ASSY. NO. PART NO. PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — MUFFLER ASSY. PAGE 78 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — MUFFLER ASSY. NO. PART NO. PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — FUEL TANK ASSY. PAGE 80 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — FUEL TANK ASSY. NO. PART NO. PART NAME 6 * 8 11 12 13 14 15 17631ZH7003 17672ZE2W01 91353671003 9405008000 950014500360M 9500202080 957010802500 GASKET, FUEL FILLER CAP FILTER, FUEL O-RING 14MM, ARAI NUT, FLANGE 8MM BULK HOSE, FUEL 4.5X3000, 4.5X222 CLIP, TUBE, B8 BOLT, FLANGE 8X25 QTY. REMARKS 1 1 1 2 1 2 2 STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — IGNITION ASSY. PAGE 82 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — IGNITION ASSY. NO. PART NO. PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — PISTON ASSY. PAGE 84 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — PISTON ASSY. NO. PART NO. PART NAME 4 5 * 6 13200ZE2305 90001ZE8000 90551ZE1000 ROD ASSY., CONNECTING, US 0.25, OPT. BOLT, CONNECTING ROD CLIP, PISTON PIN 18MM QTY. REMARKS 1 2 2 STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — RECOIL STARTER ASSY. PAGE 86 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — RECOIL STARTER ASSY. NO. PART NO. PART NAME 2 * 3 * 4 * 5 * 6 * 7 * 8 * 10 * 11 * 13 * 14 28410ZE2W01ZB 28421ZE2W01 28422ZE2W01 28441ZE2W01 28442ZE2W01 28443ZE2W01 28444ZE2W01 28461ZE2W02 28462ZE2W11 90004ZE2W01 90008ZE2003 CASE COMP., RECOIL STARTER *NH1*, BLK PULLEY, RECOIL STARTER RATCHET, STARTER SPRING, FRICTION SPRING, STARTER RETURN SPRING RATCHET RETAINER, SPRING GRIP, STARTER ROPE, RECOIL STARTER SCREW, CENTER BOLT, FLANGE 6X10 QTY.
HONDA GX240K1HA2 ENGINE — GEAR REDUCTION ASSY. PAGE 88 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — GEAR REDUCTION ASSY. NO. PART NO. PART NAME QTY. 2 3 4 5 6 7 8 9 10 * 11 12 13 14 * 15 11521ZE2800 22103ZE2620 23220ZE2621 23710ZE2621 90401ZE2620 90402ZE2620 90473842000 90745ZE2600 91201890003 9430108140 957010802500 957010804000 961006206000 961006302000 GASKET, CHAIN CASE COVER GEAR, PRIMARY DRIVE (17T) COUNTERSHAFT SHAFT, P.T.O. (H- TYPE) SHIM A (OPTIONAL) SHIM B (OPTIONAL) WASHER (8MM) KEY (6.3 X 6.
HONDA GX240K1HA2 ENGINE — LABEL ASSY. PAGE 90 — STOW MS-70 MIXER — OPERATION MANUAL — REV.
HONDA GX240K1HA2 ENGINE — LABEL ASSY. NO. PART NO. PART NAME QTY. REMARKS STOW MS-70 MIXER — OPERATION MANUAL — REV.
Effective: July 15, 2003 TERMS AND CONDITIONS OF SALE — PARTS Terms and Conditions of Sale STOW Construction Equipment PAYMENT TERMS Terms of payment for unit sales are 2% 15 days net 30 days from date of invoice unless otherwise specifically stated on our invoice. Parts invoices have terms of net 10 days. Minimum parts billing is $15.00 net. Applicable discounts will be computed on merchandise value only. Late charges will be assessed at prevailing rates.
NOTE PAGE STOW MS-70 MIXER — OPERATION MANUAL — REV.
OPERATION AND PARTS MANUAL HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 FAX: 800-672-7877 310-537-3700 FAX: 310-637-3284 SERVICE DEPARTMENT 800-478-1244 FAX: 310-537-4259 310-537-3700 TECHNICAL ASSISTANCE ^^^^^*^^^^^^^^^^^^^^^^^^^^^^^^^*^6668 800-478-1244 FAX: 310-631-5032 WARRANTY DEPARTMENT 800-421-1244, EXT. 279 FAX: 310-537-1173 310-537-3700, EXT.
