PARTS AND OPERATION MANUAL © COPYRIGHT 2001, MULTIQUIP INC. WetScreed — K200 Revision #2 (03/12/01) MULTIQUIP INC.. PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT: 310-537-3700 800-421-1244 800-478-1244 FAX: 310-537-3927 FAX: 310-537-4259 E-mail:mq@multiquip.com • www:multiquip.
PAGE 2 — Wet Screed K200 — PARTS & OPERATION MANUAL — REV.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 Wet Screed K200 — PARTS & OPERATION MANUAL — REV.
TABLE OF CONTENTS Here's How To Get Help ........................................ 3 Table Of Contents ................................................. 4 Parts Ordering Procedures ................................... 5 Explanation Of Codes In Remarks Column .......... 6 WET SCREED K200 Safety Instructions ............................................. 7-8 Specifications ........................................................ 9 What is a Wet Screed .....................................10-11 Operation .......
PARTS ORDERING PROCEDURES n n n n n n n Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • • • • UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* • • Airborne Express* Truck or parcel post *Normally shipped the same day the order
EXPLANATION OF CODE IN REMARK COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
SAFETY INSTRUCTIONS The Wet Screed models K 200 have been developed and tested in accordance with strict International Safety Standards. This section contains general advice. Regular maintenance of the Wet Screed promotes safe operation. ■ When in doubt and/or when you are operating the Wet Screed for the first time, always read the necessary instructions in this manual. ■ Wear safety shoes with extra protection (steel caps and anti-slip soles).
SAFETY INSTRUCTIONS Important Safety Checks for the electrical Wet Screed ■ Check the feeder cable and extension cords outer casing before you connect the Wet Screed to the electrical mains. ■ Check the feeder cable’s attachment on the bullfloat, before you connect the Wet Screed to the electrical mains. The cable must be correctly attached to the bullfloat . ■ Ensure that the feeder cable does not graze past any sharp objects.
SPECIFICATIONS K 200 (230VAC) Voltage Capacity Revolutions Centrifugal force Mass Fuel Mixture Sealing Insulation Motor protection Design K 200 (2 stroke gas-engine) 110VAC 1 Phase/50-60Hz 350 W 520 W 12000 r/min 12000 r/min 1800 N (405 lbs.) 1800 N (405 lbs.) 1, 5 m (13Kg) 1, 5 m (13Kg) — 2-stroke (mixture) — 1 : 25 IP 54, splash proof Class II Double Insulated IP 54, splash proof Impact and shock proof — Portable Portable (?? in.) — (?? in.) (??in.
K200 — WHAT IS A WET SCREED Figure 0.1 View of the most important components 1. Aluminium profile 2. Operating handle 6. Drive-unit 110 VAC or 230 VAC0 3. ON/OFF-switch 7. Plug 5. Cable 8. Gas Engine 9. Gas throttle PAGE 10 — Wet Screed K200 — PARTS & OPERATION MANUAL — REV.
K200 — WHAT IS A WET SCREED What is a Wet Screed? A Wet Screed is a strike-off method where the blade rides on concrete rather than form or rails. Level bases are established in long strip parallel to the forms. Once completed the contractor is then free to "wet screed" the concrete in between the two bases. Wet Screed K200 — PARTS & OPERATION MANUAL — REV.
K200 — OPERATION This section describes the operation of the K 200 Wet Screed. Tip: For the location and description of the Wet Screed’s parts, which are mentioned in the text, refer to the illustration figure (page. 9): What is a Wet Screed. How to assemble the K 200 Wet Screed. When delivered the Wet Screed is not ready for use.You only have to carry out the following procedures to assemble them: 1. 2.
K200 — OPERATIONS Operation of the Electric Wet Screed 1. Check that the Wet Screed is properly assembled and that the switch is in the ‘OFF’ position. 2. Put the plug of the drive-unit’s feeder cable in the wall socket. 3. Place the Wet Screed in the direct vicinity of where you are going to smooth the surface of the concrete-floor. 4. Place the Wet Screed on the surface of the freshly poured concrete, and turn the speed regulator slowly to the required revolutions. 5.
K200 — OPERATION Starting Procedure 1. Check that the Wet Screed is properly assembled, and the fuel tank is filled. 2. Place the Wet Screed in the direct vicinity of where your are going to smooth the surface of the concrete. 3. Adjust the throttle-lever (1) to the idle-position.(Fig 2.5) 10. After allowing a three-minute warming-up period set the throttle handle to the desired engine speed. The Wet Screed is now ready for use. Smoothing concrete 11. Adjust the right trowel blade angle.
K200 — TROUBLE SHOOTING Problem: The Wet Screed does not vibrate in the ON position. Cause: Fault in the electrical connections of the feeder cable. Solution: Check the electrical connections to the Wet Screed, switch, plug and feeder cable for breakage. Replace the faulty part(s). Problem: The Wet Screed does not get into the required number of revolutions. Cause: Voltage drop, due to the feeder cable being too long. Problem: Gas engine does not start.
K200 — MAINTENANCE AND REPAIR Maintenance Maintenance after 20 hours of operation Although the Wet Screed has few moving parts, regular maintenance promotes a long and trouble-free life. Warning: Never use a high pressure cleaner to clean a Wet Screed with an electrical or gas drive unit. 4.3 Cleaning and servicing of the electrical drive unit. Warning: Cut off the electrical supply to the Wet Screed before carrying out any maintenance activities to the Wet Screed.
K200 — MAINTENANCE AND REPAIR Maintenance after 50 hours of operation ■ Cleaning of the piston. Remove the carbon from the upper side of the piston, from the exhaust-ports in the cylinder, from the combustion chamber and from the exhaust. ■ Cleaning of the spark plug. Clean off carbon deposits on the spark plug electrode using a plug cleaner or wire brush. Check electrode gap. If necessary adjust it to between: 0.6 to 0.7 mm. Longtime storage 1.
K200 — FRAME PAGE 18 — Wet Screed K200 — PARTS & OPERATION MANUAL — REV.
K200 — FRAME K 200 FRAME NO PART NO PART NAME QTY.
K200 — ELECTRIC DRIVE-UNIT AND SWITCH PAGE 20 — Wet Screed K200 — PARTS & OPERATION MANUAL — REV.
K200 — ELECTRIC DRIVE-UNIT AND SWITCH K 200 ELECTRIC UNIT AND SWITCH NO PART NO PART NAME QTY.
K200 — ELETRIC DRIVE-UNIT COMPONENTS PAGE 22 — Wet Screed K200 — PARTS & OPERATION MANUAL — REV.
K200 — ELETRIC DRIVE-UNIT COMPONENTS K 200 ELECTRIC DRIVE-UNIT COMPONENTS NO PART NO PART NAME QTY.
K200 — GAS DRIVE-UNIT AND GAS THROTTLE PAGE 24 — Wet Screed K200 — PARTS & OPERATION MANUAL — REV.
K200 — GAS DRIVE-UNIT AND GAS THROTTLE K 200 GAS DRIVE-UNIT AND GAS THROTTLE NO PART NO PART NAME QTY.
Effective: July 1, 2000 PAYMENT TERMS TERMS AND CONDITIONS OF SALE — PARTS 4. Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier. Freight is at the sender’s expense.
NOTE PAGE Wet Screed K200 — PARTS & OPERATION MANUAL — REV.
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC.
